Bosch Professional GTA 600 Original Instructions Manual page 8

8 | English
cessories. Accidents can occur when power tools are
started unintentionally.
Assemble the saw stand properly before mounting the
u
power tool. Correct assembly is important to prevent the
risk of collapsing.
Firmly secure the power tool to the saw stand before
u
using it. You may lose control of the power tool if it slips
on the saw stand.
Place the saw stand on a firm, flat, horizontal surface.
u
If there is a chance that the saw stand will slip or wobble,
the safe and steady machining of the workpiece cannot
be guaranteed.
Do not overload the saw stand or climb or stand on it.
u
Overloading or standing on the saw stand can raise its
centre of gravity, causing it to tip over.
Do not force the workpiece into the saw blade. Exert-
u
ing excessive pressure on the power tool can cause the
saw stand to tip over.
Ensure that all screws and connecting pieces are
u
tightly fastened when carrying out work. Loose con-
nections can cause instability and inaccurate sawing.
Ensure that long and heavy workpieces do not unbal-
u
ance the saw stand. The free end of long and heavy
workpieces must have something placed underneath it or
be supported.
When pushing together or pulling apart the saw stand,
u
do not put your fingers near the points of articulation.
There is a risk of fingers being crushed.
Symbols
The following symbols may provide you with important in-
formation about the use of your saw stand. Please take note
of these symbols and their meaning. Knowing what these
symbols mean will help you to use your saw stand more ef-
fectively and more safely.
Symbols and their meaning
The maximum load bearing capacity
(power tool + workpiece) of the saw
stand is 60 kg.
Product description and
specifications
Intended Use
The saw stand is intended for holding the following Bosch
benchtop saws (stand 2023.07):
– GTS 10 J ( 3 601 M30 5.. )
The saw stand and power tool are intended for cutting
boards and profiles.
1 609 92A 8YH | (19.07.2023)
Product Features
The numbering of the components shown refers to the illus-
trations on the graphics pages at the beginning of the
manual.
(1) Swing latch
(2) Clip
(3) Base frame
(4) Saw stand leg
(5) Fastening set
(6) Housing frame of the power tool
(7) Fixing clip on the power tool
Technical Data
Saw stand
Article number
Base frame dimensions
Saw stand height
Max. load bearing capacity
(power tool + workpiece)
Weight according to EPTA-Pro-
cedure 01:2014
Values can vary depending upon the product and are subject to ap-
plication and environmental conditions. For further information
www.bosch-professional.com/wac.
Assembly
Items included
Check to ensure that all the parts listed below have been
supplied before assembling the saw stand:
– Base frame (3)
– Saw stand legs (4) (4 pieces)
– Fastening set (5) consisting of:
Cross-head screws M8 x 45 (4 pieces),
lock nuts M8 (4 pieces)
Extra tools required (not included in the delivery):
– Cross-headed screwdriver
– Open-end spanner (13 mm)
Assembling the saw stand (see figures A1−A2)
– Carefully remove all parts included in the delivery from
their packaging.
– Remove all packing material.
– Open the swing latch (1) and extend the base frame (3).
– Insert the saw stand legs (4) into the square pipes in the
base frame (3) until they are aligned with the assembly
holes.
The saw stand legs must point outwards here.
– Screw together the saw stand legs and the base frame us-
ing the nuts and bolts in the fastening set (5).
GTA 600
3 601 M22 0..
mm 450 x 520
mm 602
kg 60
kg 6.3
Bosch Power Tools