Related Manuals for Perfect-10 VK-1505
Summary of Contents for Perfect-10 VK-1505
- Page 1 Step 1 Order #XXXXX - P10 - VK-1505 Fleur - General Layout 866.652.2100 10’ Plan View Perspective View 10’ WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING © 2014 w w w . c l a s s i c e x h i b i t s . c o m...
- Page 2 Step 1 Order #XXXXX - P10 - Fleur - Backwall Assembly 866.652.2100 Item Qty. Description Steps: Left Leg Assembly NOTE: Assembly may be easiest if assembled face down on floor then lifted upright. Middle Leg Assembly 1) Connect upper curved vertical extrusions [3a,3,6] to leg assemblies [1,2,5]. NOTE: When assembling horizontals they should be Upper Curved Vertical 2) Connect lower and upper horizontal extrusions between vertical assemblies by slightly...
- Page 3 Step 2 Order #XXXXX - P10 - Fleur - Blade Attachment 866.652.2100 Decorative Blade Attachment (if accidently removed) Slide A10 Clamp into groove of square extrusion. When desired location is found, tighten set screw to secure. Attach decorative wing and blades to A10’s attached to Set- Screw...
- Page 4 Step 3 Order #XXXXX - P10 - Fleur - Backwall Attachments 866.652.2100 Accessary Attachment Light Connection Attach header support to backwall Attach lights to and then slide header into groove. backwall where desired and tighten in place. Header Header Cubby Attachment Shelf attaches to section Shelf attaches to back of 5 by setting atop pins...
- Page 5 Step 4 Order #XXXXX - P10 - Workstation Assembly 866.652.2100 Part Number Description Left Leg Assembly Right Leg Assembly Horizontal Extrusion Horiontal Extrusion w/ Door Stopper D (w/ Door Stopper) Knobs face INSIDE of workstation Steps: 1) Connect lower horizontal extrusion [C] between bottom of leg assemblies [A and B] as shown. 2) Insert Laminated infill into grooves of leg assemblies [A and B].
- Page 6 Step 5 Order #XXXXX - P10 - Workstation Assembly (Cont’d) 866.652.2100 Part Number Description Horizontal Extrusion Place internal shelf into Horizontal Extrusion workstation then Steps: place counter atop 1) Attach horizontal extrusion [E] between vertical leg assemblies [A and B] as shown below. assembled workstation.
- Page 7 Case Packing - Case 1 of 3 Order #XXXXX - P10 - 866.652.2100 Vertical Connection Bar A10’s Attached A10’s Attached Level 1 Level 5 Level 4 Level 2 Level 3 Vertical Connection Bar Additional Items: - Setup Hardware - Graphic - (3) Lights WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING ©...
- Page 8 Order #XXXXX - P10 - Case Packing - Case 2 of 3 866.652.2100 Top View Backside Shelf Cubby Level 1 WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING © 2014 w w w . c l a s s i c e x h i b i t s . c o m patent D599,121...
- Page 9 Order #XXXXX - P10 - Case Packing - Case 3 of 3 866.652.2100 Top View of Each Level Horiz. Extrusion E Horiz. Extrusion F Internal Shelf Leg Assembly Leg Assembly Inserts Counter Door Level 4 Level 1 Level 2 Level 3 Level 5 WHEN DISASSEMBLING TIGHTEN ALL KNOBS TO PREVENT LOSS DURING SHIPPING ©...