Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bosch SMS6ECI63E
Summary of Contents for Bosch SMS6ECI63E
- Page 1 Dishwasher SMS6ECI63E [en] Information for Use...
-
Page 2: Table Of Contents
Table of contents Safety .......... 4 Etagere ........... 23 General information...... 4 Folding prongs ....... 23 Intended use........ 4 Extra Clean Zone ...... 23 Restriction on user group.... 4 Basket heights........ 24 Safe installation ........ 4 Before using for the first time .. 25 Safe use ........... 6 Performing the initial configura- Damaged appliance ...... 8 tion.......... 25... - Page 3 Customer Service...... 60 Deactivate button lock.... 34 Product number (E-Nr.), produc- Interrupting programme .... 34 tion number (FD) and consecut- Terminate programme.... 35 ive numbering (Z-Nr.) ..... 61 Switching off appliance .... 35 AQUA-STOP guarantee .... 61 Basic settings........ 36 Technical specifications.... 61 Overview of basic settings ..... 36 Information regarding Free and Changing basic settings.... 38...
-
Page 4: Safety
en Safety Safety Observe the following safety instructions. General information ¡ Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe for future reference or for the next owner. ¡ Do not connect the appliance if it has been damaged in transit. Intended use Only use this appliance: ¡... - Page 5 Safety en WARNING ‒ Risk of electric shock! ¡ Incorrect installation is dangerous. ▶ Connect and operate the appliance only in accordance with the specifications on the rating plate. ▶ Always use the supplied power cable for the new appliance. ▶ Connect the appliance to a power supply with alternating current only via a properly installed socket with earthing.
-
Page 6: Safe Use
en Safety ¡ Contact between the appliance and installation lines may lead to a defect in these lines, e.g. gas pipes and power lines. Gas from a corroded gas pipe can ignite. A damaged power line can cause a short circuit. ▶... - Page 7 Safety en WARNING ‒ Risk of injury! ¡ Leaving the appliance door open may result in injury. ▶ Only open the appliance door to load or unload tableware in order to prevent accidents, e.g. through tripping. ▶ Do not sit or stand on the appliance door when open. ¡...
-
Page 8: Damaged Appliance
en Safety Damaged appliance WARNING ‒ Risk of electric shock! ¡ If the appliance or the power cord is damaged, this is danger- ous. ▶ Never operate a damaged appliance. ▶ Never operate an appliance with a cracked or fractured sur- face. ▶ Never pull on the power cord to unplug the appliance. Al- ways unplug the appliance at the mains. - Page 9 Safety en WARNING ‒ Risk of harm to health! Children can lock themselves in the appliance, thereby putting their lives at risk. ▶ With redundant appliances, unplug the power cord. Then cut through the cord and damage the lock on the appliance door beyond repair so that the appliance door will no longer close.
-
Page 10: Preventing Material Damage
en Preventing material damage pipes supplied for the drinking Preventing material damage Preventing material dam- water and waste water connec- tions are not affected here. ¡ Modified or damaged water hoses may result in material damage and Preventing material damage Safe installation damage to the appliance. -
Page 11: Environmental Protection And Saving Energy
Environmental protection and saving energy en ¡ Unsuitable cleaning agents may AquaSensor damage the appliance. The AquaSensor is an optical meas- Do not use a steam cleaner. ▶ uring device (light barrier) which So as not to scratch the finish ▶ measures the turbidity of the rinsing on the appliance, do not use water. -
Page 12: Efficient Dry
en Installation and connection marks on the appliance. These Sensor setting Description marks will disappear after the first ing low levels of active wash cycle. agents. Energy and water The delivery consists of the following: consumption are adjusted ¡ Dishwasher accordingly. ¡... -
Page 13: Drainage Connection
Installation and connection en Drainage connection Electrical connection Connect your appliance to drainage Connecting the appliance to the connection so dirty water is dis- electricity supply charged via the wash cycle. Notes ¡ Please follow the "Safety instruc- Installing the drainage connection tions"... -
Page 14: Familiarising Yourself With Your Appliance
en Familiarising yourself with your appliance Familiarising yourself with your appliance Familiarising yourself with your appliance Familiarising yourself with your appliance Appliance You can find an overview of the parts of your appliance here. Rating plate Rating plate with "E number and FD number" → Page 61. -
Page 15: Controls
Familiarising yourself with your appliance en "Detergent" → Page 29 is added to the detergent Detergent dispenser dispenser. "Bottom basket" → Page 22 Bottom basket Dispenser for special salt Add special salt to the dispenser for special salt. → "Water softening system", Page 25 Lower spray arm The lower spray arm washes the tableware in the bot- tom basket. - Page 16 en Familiarising yourself with your appliance "Switching on the appliance" → Page 33 ON/OFF button and reset button "Switching off the appliance" → Page 35 "Terminating the programme" → Page 35 "Programmes" → Page 18 Programme buttons Programme sequence display The programme sequence display shows the cur- rent cycle of the appliance, e.g. washing, rinsing or drying.
- Page 17 Familiarising yourself with your appliance en Rinse aid refill indicator Rinse aid system → "Adding rinse aid", Page 28 Water supply display Display for water supply Special salt refill indicator Water softening system → "Adding special salt", Page 26 Door handle Open the appliance door. Depending on the appliance specifications...
-
Page 18: Programmes
en Programmes Programmes Programmes You can find an overview of the pro- runtime will change if the rinse aid Programmes grammes that can be selected here. system is switched off or rinse aid Different programmes, which can be needs to be added. found on the control panel of your The consumption values can be appliance, are available depending... - Page 19 Programmes en Programme: Programme sequence Additional func- tions Tableware: Reduced noise: → "Additional ¡ Cleaning mixed table- ¡ Pre-Rinse Silence 50 ware and cutlery. functions", ¡ Cleaning 50 °C Level of soiling: Page 20 ¡ Intermediate rinse ¡ Removing common ¡ Final rinse 63 °C household food remnants ¡...
-
Page 20: Information For Test Institutes
en Additional functions Press for 3 seconds. Information for test institutes a The selected programme and the Test institutes are provided with in- additional function will flash. formation for comparability tests, e.g. flashes. according to EN60436. a The programme and the additional These are the conditions for conduct- function are saved. -
Page 21: Features
Features en Additional func- Features Features tion ¡ Switch on with mixed You can find an overview of the pos- Features loads containing table- sible features of your appliance and IntensiveZone ware with different soil- how to use them here. ing levels, e.g. place These features depend on the model very soiled pots and of your appliance. -
Page 22: Bottom Basket
en Features Press in the levers on the right and Bottom basket left on the outside of the basket. Arrange pans and plates in the bot- tom basket. Raise or lower the basket evenly to the right level. Large plates up to a diameter of 31 cm can be arranged in the bottom basket as shown. -
Page 23: Etagere
Features en Arrange cutlery with the points and Folding down prongs sharp edges downwards. If you do not need the prongs, fold them down. Etagere Push the lever forwards and fold Use the cutlery shelf and space un- down the prongs ... -
Page 24: Basket Heights
en Features Set the slider to ON or OFF. Pull the tab on the Extra Clean Zone up and forwards . Push in the top basket. Set the slider to ON. Cleaning Extra Clean Zone Clean under running water. Limescale and soiling from the dish- Place the Extra Clean Zone in the washing water can block the nozzles. -
Page 25: Before Using For The First Time
Before using for the first time en "Set the amount of rinse aid to be Before using for the first time Before using for the dispensed." → Page 28 first time "Add detergent" → Page 29. Start the Programme with the Before using for the first time highest cleaning temperature Performing the initial config- without tableware. -
Page 26: Setting The Water Softening System
en Water softening system Note: Set the water hardness determ- ATTENTION! ined on your appliance. ¡ Detergent may damage the water softening system. → "Setting the water softening sys- tem", Page 26 Only fill the dispenser of the wa- ▶ ter softening system with special With a water hardness of 0 - 8 °E you can dispense with special salt for dishwasher salt. -
Page 27: Switching Off The Water Softening System
Water softening system en Switching off the water Regeneration of the water softening system softening system If you find the special salt refill indic- In order to obtain fault-free function of ator irritating, e.g. when using com- the water softening system, the appli- bined detergents with salt replace- ance performs regeneration of the ment substances, you can switch the... -
Page 28: Rinse Aid System
en Rinse aid system Close the lid of the dispenser for Rinse aid system Rinse aid system rinse aid. a The lid clicks into position. Rinse aid system Rinse aid Setting the amount of rinse For optimum drying results, use rinse aid. -
Page 29: Detergent
Detergent en a The display shows H:xx. Detergent Description a The display shows . Powder deter- Powder detergent is re- Press repeatedly until gent commended for shorter the display shows the value set at "Programmes" → Page 18. the factory r:05. The dosage can be adjus- Press repeatedly until the ted to the level of soiling. -
Page 30: Unsuitable Detergents
en Detergent pletely dispense with certain sub- Combined detergent stances. The cleaning effect may Besides conventional separate deter- be restricted here. gents, a number of products are ¡ Set the rinse aid and the water available with additional functions. softening system to the separate These products contain not only de- detergent or combined detergent tergent but also rinse aid and salt re-... -
Page 31: Tableware
Tableware en Add the detergent to the dry deter- Close the lid of the detergent dis- gent dispenser. penser. 50 ml 25 ml 15 ml a The lid clicks into position. If you are using tablets, one is a The detergent dispenser will open enough. -
Page 32: Damage To Glass And Tableware
en Tableware Damage to glass and table- Cause Recommendation ware The water temperat- Select a programme ure of the programme with lower temperat- Only put glasses and china in the is too high. ures. dishwasher if it is marked as dish- After the programme washer-safe by the manufacturer. -
Page 33: Removing Tableware
Basic operation en To save resources, do not pre- Removing tableware rinse tableware under running wa- ter. WARNING Observe the following when arran- Risk of injury! ging tableware: Hot tableware can cause burns to the – Put heavily soiled tableware in skin. -
Page 34: Setting A Programme
en Basic operation Setting a programme Starting the programme To adjust the wash cycle to the soil- Press ▶ ing level of the tableware, select a a The programme has ended when suitable programme. the display shows "00h:00m". Press the right programme button. ▶... -
Page 35: Terminate Programme
Basic operation en few minutes and then close it. This will help prevent excess pressure building up in the appliance and stop the appliance door bursting open. Press . a The programme is saved and the appliance switches off. Press to resume the pro- gramme. -
Page 36: Basic Settings
en Basic settings Basic settings Basic settings You can configure the basic settings for your appliance to meet your needs. Basic settings Overview of basic settings The basic settings depend on the features of your appliance. Basic setting Display text Selection Description Water hardness H:04... - Page 37 Basic settings en Basic setting Display text Selection Description Start programme SP:01 SP:00 - SP:01 Set a default programme for when the appliance is switched on. ¡ With the setting "SP:00", the last programme selected is set by de- fault when the appliance is switched on.
-
Page 38: Changing Basic Settings
en Home Connect Basic setting Display text Selection Description Remote Start rc:01 rc:00 - rc:02 Activate or deactivate → "Remote Start ", Page 39. The following settings are possible: ¡ With the setting "rc:00", the func- tion is permanently deactivated. ¡ With the setting "rc:01", the func- tion can be selected via the button. -
Page 39: Home Connect Quick Start
Home Connect en The Home Connect app guides you With the help of the Home Connect through the entire login process. Fol- app scan the QR code. low the instructions in the Home Con- nect app to configure the settings. Tips ¡ Please consult the documents sup- plied by Home Connect. -
Page 40: Remote Diagnostics
en Cleaning and servicing Press . ¡ Security certificate of the Wi-Fi ▶ communication module (to ensure If you open the appliance door, the a secure data connection). function is automatically deactiv- ¡ The current software and hardware ated. version of your appliance. button lights up. -
Page 41: Cleaning Products
Wipe the door seals, This ensures the parts chine Cleaner for Dishwashers online the front of the dish- of the appliance will at https://www.bosch-home.com/ washer and the con- remain clean and hy- store or from customer service. trol panel regularly us- gienic. -
Page 42: Filter System
en Cleaning and servicing Running Machine Care Filter system Notes The filter system removes coarse ¡ Run the Machine Care programme soiling from the dishwashing cycle. without any tableware in the dish- washer. ¡ Only use machine care products and machine cleaners specially designed for dishwashers. -
Page 43: Cleaning Spray Arms
Cleaning and servicing en Pull down the micro filter to re- Insert the filter system into the ap- move. pliance and turn the coarse filter clockwise. Make sure that the arrow mark- ‒ ings match up. Press the locking catches gether and lift the coarse filter out ... - Page 44 en Cleaning and servicing Pull up the lower spray arm to re- move. Check the outlet nozzles on the spray arms for blockages under running water and remove any for- eign bodies. Insert the lower spray arm. a The spray arm clicks into position. Insert the upper spray arm and screw it firmly in place.
-
Page 45: Troubleshooting
Troubleshooting en Troubleshooting Troubleshooting You can rectify minor faults on your appliance yourself. Read the troubleshoot- Troubleshooting ing information before contacting after-sales service. This will avoid unneces- sary costs. WARNING Risk of electric shock! Incorrect repairs are dangerous. Repairs to the appliance should only be carried out by trained specialist ▶... -
Page 46: Error Code / Fault Display / Signal
en Troubleshooting Fault Cause Troubleshooting Appliance door opens too Door is not correctly adjus- Adjust the appliance door as de- ▶ wide at the end of the pro- ted. scribed in the installation instruc- gramme. tions. The door gap must be at least 70 mm - 100 mm. - Page 47 Troubleshooting en Fault Cause Troubleshooting E:32-00 will light up altern- Remove the filter from the supply ately or indicator for water hose supply lights up. Clean the filter. Re-insert the filter in the supply hose. Screw the water connection back Check the water connection for leaks.
-
Page 48: Washing Results
en Troubleshooting Fault Cause Troubleshooting E:90-01 will light up altern- Mains voltage is too low. This is not a fault on the appliance. ately. Contact an electrician. Have the mains voltage and elec- trical installation checked by an electrician. E:92-40 will light up altern- Filters are soiled or blocked. - Page 49 Troubleshooting en Fault Cause Troubleshooting Tableware is not dry. Water collects in recesses of Position tableware at an angle ▶ the tableware or cutlery. where possible. The combined detergent Use rinse aid to improve drying per- used has a poor drying per- formance.
- Page 50 en Troubleshooting Fault Cause Troubleshooting Appliance interior still wet Not a fault. The condensa- No action required. after wash cycle. tion drying principle causes water droplets in the tub – they are indeed desirable here. The moisture in the air condenses on the inside walls, runs off and is pumped out.
- Page 51 Troubleshooting en Fault Cause Troubleshooting Detergent residue in the ap- Lid of the detergent dis- Arrange tableware in the top basket pliance penser is blocked by items tableware so the tab collecting tray of tableware parts and will is not obstructed by tableware. → "Arrange tableware", Page 32 not open.
- Page 52 en Troubleshooting Fault Cause Troubleshooting Stubborn white coatings are Detergent substances are Change your "detergent" ▶ → Page 29. present on tableware, inside deposited there. These coat- the appliance or the door. ings cannot generally be re- Clean the appliance mechanically. ▶ moved with chemicals. The hardness range is set in- Set the Water softening system to ▶...
- Page 53 Troubleshooting en Fault Cause Troubleshooting Coloured coatings (blue, yel- You can remove deposits with "Mechanical cleaning" → Page 40 low, brown) that are difficult or impossible to remove are or a machine cleaning product. It present inside the appliance may not always be possible to com- or on stainless steel table- pletely remove deposits but they ware.
- Page 54 en Troubleshooting Fault Cause Troubleshooting Removable streaks are Tableware has been pre- Only remove large remnants of food ▶ present on glasses, glass- cleaned too intensely. The and do not prerinse tableware. ware with a metallic appear- sensors chose a weaker pro- Adjust the sensitivity of the sensors.
-
Page 55: Home Connect Problem
Troubleshooting en Fault Cause Troubleshooting Excessive formation of foam Detergent or appliance care Change the brand of detergent. ▶ occurs. product used causes excess- ive foaming. Home Connect problem Fault Cause Troubleshooting Connection to home net- WLAN on router is not act- Check the wireless network con- ▶... - Page 56 en Troubleshooting Fault Cause Troubleshooting → "Terminate programme", Water is left in the appliance ▶ at the end of the pro- Page 35 gramme. Appliance cannot be Software update is taking Wait until the software update has ▶ switched on or operated. place. finished.
-
Page 57: Mechanical Damage
Troubleshooting en Fault Cause Troubleshooting All LEDs lit up or flashing. Electronics have detected a Press the main switch button for ap- fault. prox. 4 seconds. → "Controls", Page 15 The appliance is reset and restar- ted. If the problem occurs again: Switch off the appliance. ‒... - Page 58 en Troubleshooting Fault Cause Troubleshooting Knocking or rattling noise. With a small load the water Distribute the tableware evenly. ▶ jets directly strike against Load the appliance with more table- ▶ the tub. ware. Light items of tableware Position light items of tableware se- ▶...
-
Page 59: Clean Wastewater Pump
Transportation, storage and disposal en Insert the pump cover and press Clean wastewater pump down . Large remnants of food or foreign bodies can block the waste water pump. As soon as the rinsing water no longer drains properly, the waste water pump must be cleaned. -
Page 60: Transporting The Appliance
en Customer Service Unplug the appliance from the Transporting the appliance mains. To avoid damage to the appliance, Cut through the power cord. empty it before transporting. Dispose of the appliance in an en- Note: Always transport the dish- vironmentally friendly manner. washer upright to prevent residual Information about current disposal water getting into the machine's con-... -
Page 61: Product Number (E-Nr.), Produc- Tion Number (Fd) And Consecut- Ive Numbering (Z-Nr.)
Technical specifications en The contact details for Customer Ser- defective supply lines or fittings up vice can be found in the enclosed to the Aqua-Stop connection on Customer Service directory or on our the tap. website. ¡ If your appliance is fitted with Aqua-Stop, you can in principle Product number (E-Nr.), pro- leave your appliance unattended... -
Page 62: Information Regarding Free And Open Source Software
äte GmbH, Carl-Wery-Str. 34, 81739 A detailed Declaration of Conformity Munich, Germany. can be found online at www.bosch- The source code will be made avail- home.co.uk among the additional able to you on request. documents on the product page for Please send your request to oss- your appliance. - Page 63 Declaration of Conformity en 5 GHz WLAN (Wi-Fi): For indoor use only.
- Page 64 Expert advice for your Bosch home appliances, help with problems or a repair from Bosch experts. Find out everything about the many ways Bosch can support you: www.bosch-home.com/service Contact data of all countries are listed in the attached service direct- ory.