Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Champion TMM4 Plus
Summary of Contents for Champion TMM4 Plus
- Page 1 OWNER'S OPERATING AND MAINTENANCE MANUAL Wide Tall Rail on Back Section Scale ENG Headpiece Folding Footrest Battery AC Power TMM4 Plus TMM4 Plus-X TMM4 Plus & TMM4 Plus-X MULTI-PURPOSE PROCEDURE-CHAIR SERIES 1-800-237-3377 CHAMPIONCHAIR.COM Document No. ???????? Rev B...
-
Page 2: Important Notes About This Manual
Champion assumes no responsibility for damage or injury caused by improper assembly, installation, use, or maintenance of these products. No part of this manual may be duplicated in any form without the prior consent of Champion Manufacturing, Inc. Unauthorized duplication/distribution of these materials may result in civil prosecution to the maximum extent allowed by law. -
Page 3: Table Of Contents
Transportation, Storage, Handling & Disposal ................ 4 Preparation: Before You Begin ....................4 Power Cable Requirements ......................5 Safety Precautions ........................5 Labeling Diagrams (TMM4 Plus-B Shown) ................11 Options ............................12 Operating Instructions........................13 Back Section Quick Release ....................13 Caster Brake Operation...................... -
Page 4: Intended Use Statement
The product should be stored in an environment that will inhibit rust/mold formation. • "“A” Model chairs – Champion Manufacturing, Inc. recommends not leaving the product in storage in excess of two (2) months. Permanent battery damage could result. •... -
Page 5: Power/Cable Requirements
POWER/CABLE REQUIREMENTS Only use the power/charging cord that came with your product. See also sections for options A & B for additional details regarding powering this product. SAFETY PRECAUTIONS WARNING IMPORTANT: PLEASE READ WARNINGS CHAIR OPERATION BY QUALIFIED, TRAINED MEDICAL PERSONNEL ONLY The chair is intended to be operated only by qualified, trained medical staff. - Page 6 SAFETY PRECAUTIONS – CONTINUED WARNING IMPORTANT: PLEASE READ USE CAUTION WHEN STORING OXYGEN CYLINDER UNDER CHAIR To prevent severe gas leakage or rupture of compressed gas cylinder, when placing cylinder under chair, ensure adequate clearance between cylinder and its attached gas equipment (i.e. regulator, gauges, fittings, knobs) and all adjustable chair sections and/or features (i.e.
- Page 7 If mounting accessories to back surgical rails, ensure accessory is properly installed and securely engaged prior to transporting patient or chair and prior to use. Only equipment approved by Champion is to be mounted on surgical rails. Champion Manufacturing, Inc. is not responsible for damage and assumes no liability caused by the use of unapproved equipment or accessories.
- Page 8 Prior to operating chair, ensure patient clearance by moving any overhanging equipment or moving chair from under a table to prevent patient injury. For TMM4 PLUS, chair must be at least 20 inches from nearest wall or obstruction to allow for full range of activation.
- Page 9 SAFETY PRECAUTIONS – CONTINUED WARNING IMPORTANT: PLEASE READ EMI CAUTIONS EMI MAY AFFECT CHAIR FUNCTIONALITY Chair may be susceptible to EMI (Electromagnetic Interference) caused by electromagnetic energy emitted from various sources, such as, radio and television stations, amateur radio (HAM) transmitters, citizen band (CB) radios, hand-held “walkie-talkies”, security/police/fire transceivers and other communication devices.
- Page 10 SAFETY PRECAUTIONS – CONTINUED WARNING IMPORTANT: PLEASE READ IMPORTANT MAXIMUM PATIENT WEIGHT IS 500 lbs (227 kg) Maximum patient weight capacity of chair is 500 pounds. If exceeded, damage to chair could occur. CHAIR IS INTENDED FOR INDOOR USE ONLY To ensure proper operation and extend chair life, only use chair in specified environment. ...
-
Page 11: Labeling Diagrams (Tmm4 Plus-B Shown)
Champion Customer Service at 1-800-237-3377. Item No. Part No. Description TMM-2449-10 TMM4 X Plus Bse Cover Label (Side) TMM-2446-10 TMM4 Plus Base cover label (side) TMM-2448-10 Label Base Cover TMM-2247-10 Label, Qr Code TMM Videos TMM-1216-10 Blank Serial Number Label TMM-754-10... -
Page 12: Options
OPTIONS BATTERY OPTION UPPER SIDE RAIL OPTION DESIGNATOR. “B” DESIGNATOR. “R” TMM-311-03 Mobillette Battery Pack TMM-214-10 Product Label – Small TMA57-15 Universal Charger Assembly TMM-214-10 Product Label – Small ITEM NO. PART NO. DESCRIPTION QTY. ITEM NO. PART NO. DESCRIPTION QTY. -
Page 13: Operating Instructions
OPERATING INSTRUCTIONS QUICK RELEASE BACK SECTION FIG. 1 1. LOCATE RELEASE LEVER Back section quick release (red) lever is located under seat on patient’s right side. (Fig. 1) 2. ACTIVATE RELEASE LEVER To activate back section quick release, pull red lever out towards the arm rail. ... -
Page 14: Caster Brake Operation
CASTER BRAKE OPERATION BRAKE MODE FIG. 1 Activate braking system by pressing down on red end of either brake pedal located at base of chair.(Fig. 1) NOTE: This mode prevents all four casters from swiveling and all wheels from spinning. NEUTRAL MODE FIG. -
Page 15: Side Rail Operation
SIDE RAIL OPERATION LOWERING SIDE RAIL Grasp top of side rail and push inward slightly, while pulling out red rail release tab. Once released, lower rail. (Fig. 1) FIG. 1 STOWING SIDE RAIL To stow side rail, lower rail into “down” position below seat (or back section depending on rail location). -
Page 16: Adjusting Side Rail Angle
ADJUSTING SIDE RAIL ANGLE FIG. 1 1. Remove seat cushion to expose access holes in seat pan. 2. Loosen top jam nut found in access holes. (Seat pan is not shown in image for instruction purposes only and to allow visibility of jam nut). 3. -
Page 17: Pendant (Controller)
PENDANT (CONTROLLER) PENDANT IS NOT INTENDED FOR PATIENT’S USE WARNING To prevent damage, pendant can be stored at various locations on the chair when not in use. ENSURE AREA IS CLEAR OF OBSTRUCTIONS PRIOR TO PENDANT USE WARNING To prevent property damage or injury to patient, survey area for possible obstructions prior to pendant use. - Page 18 PENDANT (CONTROLLER) – CONTINUED BACK SECTION ADJUSTMENT First row of pendant buttons adjusts angle of back section. a. Press left button to raise chair back. b. Press right button to lower chair back. LEG SECTION ADJUSTMENT Second row of pendant buttons adjusts angle of leg section. a.
-
Page 19: Patient Ingress/Egress
PATIENT INGRESS/EGRESS PATIENT SHOULD NEVER BE PERMITTED TO ENTER / EXIT FROM ENDS OF WARNING PROCEDURE CHAIR WHEN IN AN UPRIGHT, PARTIALLY, OR TOTALLY RECLINED POSITION. EXCESSIVE WEIGHT ON ENDS COULD CAUSE CHAIR TO TILT, RESULTING IN POSSIBLE PATIENT INJURY. IMPORTANT: Follow these instructions for safe and proper patient ingress (entry onto chair) and egress (exit from chair). -
Page 20: Patient Transfer
PATIENT TRANSFER PATIENT’S BODY WEIGHT SHOULD NEVER BE SHIFTED TOWARDS EITHER END OF CHAIR WHEN IN A PARTIALLY, OR TOTALLY, RECLINED POSITION. SERIOUS WARNING PATIENT INJURY MAY OCCUR. ALL PATIENT TRANSFERS MUST BE MADE FROM SIDE OF CHAIR, NOT CHAIR ENDS. IMPORTANT: Follow these instructions for safe and proper patient transfer between chair (in stretcher orientation) and another horizontal surface. -
Page 21: Options
OPTIONS “W” OPTION: WIDE WIDTH For “W” option, patient surface width is 28”. Standard width is 24”. 24” standard 28” “W” option “T” OPTION: TALL HEIGHT & “L” OPTION: LOW HEIGHT For “T” option, chair height travel is 16”. Standard travel is 8”. NOTE: To prevent chair damage, ensure ground clearance is at least 1.75”... -
Page 22: R" Option: Rails On Back Section (Near Patient's Head)
“R” OPTION: RAILS ON BACK SECTION (NEAR PATIENT’S HEAD) Rails located on back section operate and adjust same as side rails. BE AWARE OF PINCH POINTS WARNING BETWEEN PARTS WHEN RAISING OR LOWERING BACK. “R” option doesn’t have push handles. Page 22 of 35 manual Document No.: ??????? - Revision: B... -
Page 23: Q" Option: Scale
“Q” OPTION: SCALE TO MEASURE PATIENT’S WEIGHT WITH SCALE: 1. Ensure chair base is level. 2. Ensure chair is not contacting nearby objects. 3. Activate chair’s caster brakes. 4. To tare scale, press and hold the “ZERO” button for approximately 3 seconds until “ZERO” appears on the display, release button and the display will read 0.0. ... -
Page 24: G" Option: Eng Headpiece
“Q” OPTION: SCALE – CONTINUED CHANGING PENDANT BATTERY Follow these instructions if pendant does not wake up when “WEIGH” button is pressed. 1. Remove battery cover on back of pendant by sliding it downwards. 2. Take out battery and replace it with a new 9V Industrial battery. -
Page 25: F" Option: Folding Footrest
“F” OPTION: FOLDING FOOTREST WHEN POSITIONING FOOTREST, WARNING BE AWARE OF PINCH POINTS. To stow footrest, place both hands on red handles and lift. NOTE: For patient comfort, stow footrest prior to Extended articulating chair into supine (stretcher) position. Footrest AVAILABLE PLUG CONFIGURATIONS FOR EXPORT “A”... -
Page 26: B" Option: Battery Pack
“B” OPTION: BATTERY PACK REMOVING BATTERY PACK FROM CHAIR Grasp integrated handle on battery pack and lift up until cam locks disengage. Pull battery away from mounting bracket. INSTALLING BATTERY PACK ONTO CHAIR Place two round, cam locks on back of battery into square openings of mounting bracket. ... -
Page 27: A" Option: Ac Power (For On-Board Batteries And Charger)
“A” OPTION: AC POWER (FOR ON-BOARD BATTERIES AND CHARGER) AC power cord for charging batteries is attached to chair base, and may be stowed by wrapping around storage bracket. Fig. 1 TO CHARGE ON-BOARD BATTERIES: 1. Insert AC plug into wall outlet (Fig. 1). NOTE: To prevent insufficient power, plug chair in to charge batteries overnight (i.e. -
Page 28: Cleaning Instructions
Check for damage facility policies air dry disinfectants & water As required/in Wipe with damp Facility approved Champion accordance with cloth and allow to detergents, Check for damage Accessories facility policies air dry disinfectants & water... - Page 29 GENERAL CARE & CLEANING Proper care is essential in ensuring the durability and reliability of Champion upholstery. In general, all products should be: 1. Cleaned 2. Disinfected (per facility policy) 3. Rinsed 4. Allowed to air dry It is important to note that the terms “disinfecting” and “cleaning” should not be used interchangeably.
-
Page 30: Pad Removal Instructions
• Inspect for tattered, torn, Every three All Labels Customer Service for months missing, and illegible labels. new labels. Call Champion • Test function of each button Every three Service if pendant Pendants • Inspect pendant label to ensure... -
Page 31: Battery Safety & Charging Information
BATTERY SAFETY INFORMATION TO PREVENT PERSONAL INJURY TO PATIENT AND / OR MEDICAL PERSONNEL, WARNING ENSURE BATTERY REPLACEMENT IS PROPERLY INSTALLED AND SECURELY ENGAGED PRIOR TO USE OF ACCESSORY. TO PREVENT PERSONAL INJURY TO PATIENT AND / OR MEDICAL PERSONNEL, WARNING ENSURE BATTERY REPLACEMENT IS INSTALLED BY PERSONNEL WHO HAVE THOROUGHLY READ INSTALLATION INSTRUCTIONS. - Page 32 BATTERY LIFE NOTE: Battery capacity diminishes over time. Charge batteries regularly to maintain healthy battery life. Recommended to replace battery every two (2) years or as required. WARNING Use of batteries that are NOT factory approved will void any and all warranties. SUGGESTED PROTOCOL FOR CHARGING YOUR TMM BATTERY: 1.
-
Page 33: Specifications
SPECIFICATIONS TMM4 Plus TMM4 Plus-X Procedure Chairs TMM4 Plus-B TMM4 Plus-LB TMM4 Plus-TB TMM4 Plus-WB TMM4 Plus-TLB TMM4 Plus-WTB Maximum Patient Weight 500 lb. (227 kg) 500 lb. (227 kg) 500 lb. (227 kg) 500 lb. -
Page 34: Service & Contact Information
We reserve the right to add or delete products at any time and without prior notice. Always provide your product's specific serial number when ordering any replacement parts. When in doubt, contact a Champion representative (352-854-2929 or 1-800-237-3377) for further information. - Page 35 Information contained in this document is based on the latest product data available at the time of printing. Photography, artwork, text and specifications are subject to change. Photographs may show optional items. Champion Manufacturing Inc. reserves the right to make changes to products, materials, options, and/or specification at any time without notice or obligation. Always provide your product's specific serial number when ordering replacement parts.