Table of Contents
Advertisement
Quick Links
TMG-GSB32
PRODUCT MANUAL
v2023.10.04
32" SELF-PROPELLED
ROTARY SNOW BROOM
Please read and understand the product manual completely before assembly
Check against the parts list to make sure all parts are received
Wear proper safety goggles or other protective gears while in assembly
Do not return the product to dealer. They are not equipped to handle your requests.
Missing parts or questions on assembly?
Please call: 1-877-761-2819 or email: cs@tmgindustrial.com
www.tmgindustrial.com
TOLL FREE:1-877-761-2819
Advertisement
Table of Contents
Related Manuals for TMG TMG-GSB32
Summary of Contents for TMG TMG-GSB32
- Page 1 TMG-GSB32 PRODUCT MANUAL v2023.10.04 32” SELF-PROPELLED ROTARY SNOW BROOM Please read and understand the product manual completely before assembly Check against the parts list to make sure all parts are received Wear proper safety goggles or other protective gears while in assembly Do not return the product to dealer.
-
Page 2: Table Of Contents
TABLE OF CONTENTS HAZARD SYMBOLS AND MEAMINGS..............................3 INTRODUCTION..................................4 Safety statements................................4 GENERAL SAFETY PRECAUTIONS..............................5 MAIN COMPONENTS..................................7 PACKAGE CONTENTS..................................8 ASSEMBLY......................................9 ENGINE OPERATION..................................11 OPERATION.......................................12 During use..................................13 SERVICE & REPAIR - GENERAL.................................15 STORAGE......................................15 TROUBLESHOOTING..................................15 MAINTENANCE....................................16 EXPLODED VIEW & PARTS LIST................................17 Exploded view-main frame assembly.........................17 Parts list-main frame assembly...........................18 Exploded view-drive system............................19 Parts list - drive system..............................20... -
Page 3: Hazard Symbols And Meamings
HAZARD SYMBOLS AND MEAMINGS WARNING! WARNING! Read the instructions before operating the machine. DANGER! Ejected objects. Do not turn the brush towards onlookers or animals. DANGER! Keep people, children and animals away from the work area. DANGER! Keep hands and feet away from rotating parts. DANGER! Always use hearing protectors. -
Page 4: Introduction
INTRODUCTION Please read this entire manual prior to operating the equipment. It instructs you how to safely and easily set up, operate and maintain your machine. Please be sure that you , and any other persons who will operate the machine, carefully follow the recommended safety practices at all times.Failure to do so could result in personal injury or property damage. -
Page 5: General Safety Precautions
GENERAL SAFETY PRECAUTIONS WARNING READ MANUAL PRIOR TO INSTALL Improper installation, operation, or maintenance of this equipment could result in serious injury or death. operators and maintenance personnel should read this manual as well as all manuals related to this equipment and the prime mover thoroughly before beginning installation, operation, or maintenance. - Page 6 WARNING SAFELY MAINTAIN AND REPAIR EQUIPMENT • Do not wear loose clothing, or any accessories that can catch in moving parts. If you have long hair, cover or secure it so that it does not become entangled in the equipment. •...
-
Page 7: Main Components
MAIN COMPONENTS A. Chassis B. Engine C. Fuel Tank D. Handle E. Dashboard F. Brush Safety Guard G. Brush H. Caster Wheels I. Wheel J. Fixing accessories equipment www.tmgindustrial.com 7/22 TOLL FREE:1-877-761-2819... -
Page 8: Package Contents
PACKAGE CONTENTS Position Description Handle with pre-installed rods and wires Handle fastening screws Handle fastening bolts Spark plug removal key Nuts and bolts NOTES: 1. Cautiously open the packaging, paying attention not to lose components. 2. Consult the documentation in the box, including these instructions. 3. -
Page 9: Assembly
ASSEMBLY Noted: Please note that during assembly, maybe you’ll need a helper! 1. Forward and brush control cable assembly Couple the cable eyelet to the specific opening (fig. 3). NOTE: The cables are already pre-assembled on the dashboard. 2. Handle assembly The handle is delivered with the dashboard already assembled. - Page 10 3. Installation of the gear control Remove the previously assembled articulated joint (fig. 5.A) on the washer gear control (fig. 5.B) and nut (fig. 5.C). Insert the articulated joint (fig. 5.A) of the gear control in the hole on the lever (fig. 5.D) to connect it to the transmission. Secure the washer (fig.
-
Page 11: Engine Operation
ENGINE OPERATION NOTICE: THE MOTOR IS DELIVERED WITHOUT OIL AND GASOLINE. Oil Filling: Place the motor in a horizontal position. Remove the plug and fill with oil right to the edge. (Figure 7) Fuel: Use lowest available octane unleaded fuel. When filling, place the machine in a horizontal position. always replace old fuel. always stop the motor when fueling. -
Page 12: Operation
OPERATION CAUTION A BROOM IS A DEMANDING MACHINE. Only fully trained operators or trainee operators under supervision of a fully trained person should use this machine. Before operating broom: Operate broom controls in an off-road location. Be sure that you are in a safe area, away from traffic or other hazards. ... -
Page 13: During Use
During use Directing Debris Avoid excessive downward pressure on the brush sections to prevent excessive wear. A two to four inch wide pattern is sufficient for most applications. Direct debris by angling the brush head in that direction. Observe wind direction. - Page 14 Heavy Debris Reduce forward speed and work without using the entire machine working width. WARNING SAFELY OPERATE EQUIPMENT Do not operate equipment until you are completely trained by a qualified operator in how to use the controls, know its capabilities, dimensions, and all safety requirements. See your prime movers manual for these instructions.
-
Page 15: Service & Repair - General
SERVICE & REPAIR - GENERAL Repair or adjust the broom in a safe area, away from traffic and other hazards. Before adjusting or servicing remove spark plug wire from spark plug. STORAGE NOTICE: Do not store the broom with weight on the brush. Weight will deform the bristles, destroying the sweeping ... -
Page 16: Maintenance
MAINTENANCE MAINTENANCE SCHEDULE BEFORE EACH PROCEDURES 25 HOURS 100 HOURS AFTER EACH USE Hardware - Inspect & tighten Engine & Air Filter - check & clean if necessary Oil, engine - check level Wash Unit - Remove Grease & Debris Maintenance If you need to change the belts, please contact the distributor or local agent. -
Page 17: Exploded View & Parts List
EXPLODED VIEW & PARTS LIST EXPLODED VIEW-MAIN FRAME ASSEMBLY 1 2 3 4 5 61 60 www.tmgindustrial.com 17/22 TOLL FREE:1-877-761-2819... -
Page 18: Parts List-Main Frame Assembly
PARTS LIST-MAIN FRAME ASSEMBLY PART NO. DESCRIPTION PART NO. DESCRIPTION Connecting rod Output shaft Hexagon lock nuts M6 Hexagon bolts M10x15 Hexagon l nuts M8 Plain washer Ø10 Hole pin Brush washer Hexagon lock nuts M8 Brush Direction plate Hexagon bolts M8x25 (left) B pin Hexagon nut M10 Direction seat... -
Page 19: Exploded View-Drive System
EXPLODED VIEW-DRIVE SYSTEM www.tmgindustrial.com 19/22 TOLL FREE:1-877-761-2819... -
Page 20: Parts List - Drive System
PARTS LIST - DRIVE SYSTEM PART NO. DESCRIPTION PART NO. DESCRIPTION Hexagon lock nuts M6 Hexagon bolts M6x16 Pulley seat Inner bearing seat Hexagon head screw M6x12 Bearing 6000 Short cable Sexi-shaft Pulley Circlip Ø25 Sleeve Shift bearing Hexagon bolts M6x20 Rubber ring seat Transmission box Rubber ring... -
Page 21: Exploded View-Cortnol System
EXPLODED VIEW - CORTNOL SYSTEM B6 B7 www.tmgindustrial.com 21/22 TOLL FREE:1-877-761-2819... -
Page 22: Parts List -Cortnol System
PARTS LIST - CORTNOL SYSTEM PART NO. DESCRIPTION PART NO. DESCRIPTION Hexagon bolts M10x25 Angle handle Hexagon bolts M10x45 Hexagon nut M10 Lower handle Gear handle Hexagon bolts M8x40 Preset spring Washer Ø8 Long cable Hexagon nut M8 Panel Spring washer Ø8 B pin Upper handle left Plain washer Ø8...
Need help?
Do you have a question about the TMG-GSB32 and is the answer not in the manual?
Questions and answers