Table of Contents
Advertisement
Owner's Manual
JCRRFTSMRN°J
LAWN TRACTOR
18.5 HP, 42" Mower
Electric Start
Automatic Transmission
Model No.
917.275764
[_
his product has a low emission engine which operates
differently from previously
built engines. Before you start the
engine, read and understand
this Owner's Manual.
IMPORTANT:
Read and follow all Safety
Rules and Instructions before
operating this equipment.
For answers to your questions
about this product, Call:
1-800-659-5917
Sears Craftsman Help Line
5 am - 5 pm, Mon - Sat
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A
Visit our Craftsman
website:www.sears.com/craftsman
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Craftsman 917.275764
Summary of Contents for Craftsman 917.275764
- Page 1 Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A Visit our Craftsman website:www.sears.com/craftsman built engines. Before you start the this Owner's Manual. For answers to your questions about this product, Call: 1-800-659-5917 Sears Craftsman Help Line 5 am - 5 pm, Mon - Sat...
- Page 2 Warranty... 2 Safety Rules... 3 ProductSpecifications... 6 AssemblyPre-Operation ...8 Operation... 11 Maintenance ... 18 LIMITED WARRANTY ON CRAFTSMAN 2-YEAR ON TRACTOR When used and maintained according tor fails due to a defect in material purchase, call 1-800-4-MY-HOME® During the first 30 days of purchase, your home.
- Page 3 IMPORTANT: This cutting machine ing objects. Failure to observe injury or death. _,WARNING: In order to prevent cidental starting when setting porting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact plug. _UkWARNING: Do not coast down neutral, you may lose control...
- Page 4 I1.SLOPE OPERATION Slopes are a major factorrelated to loss of controland tip-over accidents,which can result in severeinjury or death. Opera- tion on all slopes requires extra caution. you cannot back up the slope or if you feel uneasy on it, do not mow it. •...
- Page 5 • Remove gas-powered equipment the truck or trailer and refuel it on the ground. If this is not possible, refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle. • Keep the nozzle in contact of the fuel tank or container all times until fueling is complete.
- Page 6 Sears service section of this manual). 3.5 Pints REPAIR PROTECTION AGREEMENTS RC12YC Congratulations chase. Your new Craftsman@ designed and manufactured dependable ucts, it may require time. That's tion Agreement aggravation. Purchase a Repair now and protect hassle and expense.
- Page 7 Steering Wheel insert Steering Boot (1) Hex Bolt 5/16-18 Slope Sheet Steering Wheel (1) Large Flat Washer Extension Shaft Steering (1) 5/16 Lock Washer Seat (1) Washer 17/32 x 1-3/16 x 12 Gauge _(1) Knob For Future Use Steering Wheel Adapter Keys...
- Page 8 Your new tractor has been assembled unassembled for shipping purposes. all parts and hardware you assemble as necessary to insure proper TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Standard wrench sizes you need are listed below. (1) 3/4"...
- Page 9 Slide seat until a comfortable is reached which allows you to press clutch/brake pedal all the way down. Get off seat without moving justed position. Raise seat and tighten adjustment securely. Seat Seat Flat Washer Adjustment Knob _ CHECK BATTERY Lift seat pan to raised position.
- Page 10 CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Cor- rect tire pressure is importantfor best cutting performance. • Reduce tire pressure to PSI shown "PRODUCT SPECIFICATIONS" of this manual. CHECK DECK LEVELNESS For best cutting results, mower hous-...
- Page 11 These symbols may appear on your tractor Learn and understand their meaning. REVERSE NEUTRAL HIGH ENGINE OFF REVERSE ENGINE ON OPERATION SYSTEM (ROS) FUEL OIL PRESSURE OVER TEMP LIGHT ATTACHMENT ATTACHMENT CLUTCH DISENGAGED CLUTCH ENGAGED LIGHTS ON FREE WHEEL (Automatic Models only) DANGER, KEEP HANDS...
- Page 12 KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL TRACTOR Compare the illustrations with your tractor various controls and adjustments. Attachment Clutch Lever Ligl Throttle/Choke Control Clutch/Brake Pedal Freewheel Control Our tractors conform to the safety standards of the American National Standards ATTACHMENT CLUTCH LEVER...
- Page 13 The operation of any tractor eyes, which can result in severe or eye shields while or repairs. We recommend mask worn over spectacles. HOW TO USE YOUR TRACTOR TO SET PARKING BRAKE Your tractor is equipped with an operator presence sensing switch.
- Page 14 TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground mower is at the desired cutting operating position. Gauge wheels keep the deck in proper position prevent scalping in most terrain NOTE: Adjust gauge wheels on a flat level surface.
- Page 15 TO OPERATE ON HILLS _WARNING: Do not drive up or down hills with slopes greater than 15 ° and do not drive across any slope. Use the slope guide at the back of this manual. • Choose the slowest speed ing up or down hills.
- Page 16 TO START ENGINE When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. Be sure freewheel control transmission engaged position.
- Page 17 MOWING TIPS • Mower should be properly leveled best mowing performance. LEVEL MOWER HOUSING" Service and Adjustments section manual. • The left hand side of mower used for trimming. • Drive so that clippings are discharged onto the area that has already cut.
- Page 18 MA,.TE.A.CE SC.EOULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE Check Brake Operation Check Tire Pressure Check Operator Presence ROS Systems Check for Loose Fasteners Sharpen/Replace Mower Blades Lubrication Chart Check Battery Level Clean Battery and Terminals Check Transaxle Cooling Check V-Belts Check Engine...
- Page 19 TRACTOR Alwaysobserve safetyrules when per- formingany maintenance. BRAKE OPERATION If tractor requiresmore than five (5) feet to stop at highest speed in highest gear on a level,dry concrete or paved surface,then brakemust be checkedand adjusted. (See "TOADJUST BRAKE"in the Service and Adjustmentssectionof this manual).
- Page 20 • To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied balancer.) NOTE: Do not use a nail for balancing blade. The lobes of the center appear to be centered, but are not.
- Page 21 Oil Drain Valve Closed Locked Position Yellow CaF Unlock drain valve by pushing slightly and turning counterclockwise. To open, pull out on the drain valve. After oil has drained completely, and lock the drain valve by pushing inward and turning clockwise pin is in the locked position...
- Page 22 MUFFLER Inspect and replace corroded spark arrester (if equipped) as it could cre- ate a fire hazard and/or damage. SPARK PLUG(S) Replace spark plug(s) at the beginning of each mowing season or after every 100 hours of operation, whichever first. Spark plug type and gap setting shown...
- Page 23 WARNING: SERVICE OR ADJUSTMENTS: TO AVOID Depress clutch/brake Place motion control Place attachment Turn ignition key to "STOP" Make sure the blades Disconnect spark come in contact TRACTOR TO REMOVE MOWER Mower will be easier to remove right side of tractor. Place attachment clutch GAGED"...
- Page 24 TO LEVEL MOWER HOUSING Adjust the mower while tractor on level ground or driveway. Make sure tires are properly inflated (See "PRODUCT SPECIFICATIONS" section of this man- ual). If tires are over or underinflated, will not properly adjust your mower. SIDE-TO-SIDE ADJUSTMENT •...
- Page 25 Mandrel Idler Pulley TO CHECK AND ADJUST BRAKE Your tractor is equipped with an adjustable brake system which is mounted right side of the transaxle. If tractor requires more than five (5) feet to stop at highest speed in highest level, dry concrete or paved surface,...
- Page 26 Engine Pulley J Clutching Idler _ _o_1 TrK;;P_srsion _,-,--_ Input Pulley TRANSAXLE MOTION CONTROL VER NEUTRAL ADJUSTMENT The motion control lever has been preset at the factory and adjustment be necessary. Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.
- Page 27 If "jumpercables"are used for emergency starting, follow this procedure: IMPORTANT:Yourtractor is equipped with a 12volt system.The othervehicle must also be a 12volt system.Do not use your tractor battery to start other vehicles. TO ATTACHJUMPERCABLES- 1. Connect one end of the RED cable to the POSITIVE(+) terminal of each battery(A-B),taking care not to short against tractorchassis.
- Page 28 ENGINE Maintenance, repair, or replacement emission control devices and systems, are being done at the customers may be performed by any non-road repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet. TO ADJUST THROTTLE CONTROL CABLE...
- Page 29 Immediately prepare your tractor age at the end of the season tor will not be used for 30 days or more. _,CAUTION: Never store the tractor with gasoline in the tank inside where fumes may reach an open flame or spark. Allow the engine to cool before storing...
- Page 30 TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE Will not start 1. Out of fuel. Engine properly. Engine Bad spark plug. Dirty air filter. Dirty fuel filter. Water 8. Loose or damaged wiring. 9.
- Page 31 TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE Loss of power Faulty spark plug. (cont.) Dirty fuel filter. Stale or dirty fuel. Water 10. Spark 11. Dirty engine 12. Dirty/clogged 13. Loose 14. Carburetor 15.
- Page 32 TROUBLESHOOTING CHART: See appropriate section in manual unless directed to Sears service center PROBLEM CAUSE Mower blades will 1. Obstruction not rotate mechanism• Worn/damaged belt. Frozen idler pulley• Frozen blade Poor grass Engine discharge Travel speed Wet grass• Mower deck not level• Low/uneven Worn, Buildup...
- Page 33 TRACTOR - - MODEL NUMBER 917.275764 SCHEMATIC 02831 193372 YOUR TRACTOR EQUIPPED ALTERNATOR THE LIGHTS ARE NOT CONNECTED BATTERY, OWN ELECTRICAL IGNITION SWITCH BECAUSE BRIGHTNESS POSITION CIRCUIT "MAKE" WILL CHANGE WITH ENGINE SPEED. M+G+A1 WILL DIM. AS THE ENGINE IS...
- Page 34 TRACTOR - - MODEL NUMBER 917.275764 ELECTRICAL 24 X...
- Page 35 TRACTOR - - MODEL NUMBER 917.275764 ELECTRICAL NOTE: All component dimensions given in U.S. inches PART DESCRIPTION 163465 Battery 74760412 Bolt Hex Hd 1/4-20 unc x 3/4 176689 Box Battery 176138 Switch, Interlock 183759 Harness Asm Light W/4152j 4152J Bulb Light #1156 4799J Cable Battery 6 Ga.
- Page 36 TRACTOR - - MODEL NUMBER 917.275764 CHASSIS AND ENCLOSURES chassis-Laser-It.stir...
- Page 37 TRACTOR CHASSIS AND ENCLOSURES NOTE: All component dimensions given in U.S. inches - - MODEL NUMBER 917.275764 PART DESCRIPTION 174619 Chassis 176554 Drawbar 17060612 Screw 3/8-16 x 3/4 155272 Bumper Hood/Dash 193510X012 Dash STD533710 Bolt, Carriage 3/8-16 x 3/4 174996 Panel, Dash, L.H.
- Page 38 TRACTOR - - MODEL NUMBER 917.275764 GROUND DRIVE 16 _ 59 158 82 165 156 _/39 36 35 drive-hydro.stlt...
- Page 39 TRACTOR - - MODEL NUMBER 917.275764 GROUND DRIVE PART DESCRIPTION Transaxle Peerless LTH2000 (See Breakdown) 192502 Rod Shift Fender Adjust STD561210 Pin Cotter 1/8 x 1 CAD 10040400 Washer Lock Hvy Helical 74490544 Bolt Hex FLGHD 5/16-18 Gr.5 STD541431 Nut Lock Hex W/Ins. 5/16-18 unc...
- Page 40 TRACTOR - - MODEL NUMBER 917.275764 STEERING ASSEMBLY \ +_ +-q_+],-+- +] ] r-_--_.42 \ ... 45%. steering plJt...
- Page 41 TRACTOR - - MODEL NUMBER 917.275764 STEERING ASSEMBLY NOTE: All component dimensions given in U.S. inches PART DESCRIPTION 186780 Steering Wheel 184706 Axle Assembly Cast Iron 169840 Spindle Assembly, L.H. 169839 Spindle Assembly, R.H. 6266H Bearing, Race, Thrust, Hardened 121748X Washer 25/32 x 1-5/8 x 16 Ga.
- Page 42 TRACTOR - - MODEL NUMBER 917.275764 ENGINE OPTIONAL EQUIPMENT Spark Arrester KEY PART DESCRIPTION 170545X505 Control, Throttle/Choke 17720408 Screw, Hex Head, Thread Cutting 1/4-20 x 1/2 Engine, Briggs Model 31P777- 0602-E2 (See Breakdown) 137352 Muffler 165291 Gasket 148456 Tube Drain Oil Easy...
- Page 43 TRACTOR - - MODEL NUMBER 917.275764 SEAT ASSEMBLY seat It.knob PART DESCRIPTION 188716 Seat 180166 Bracket Pnt Pivot Seat (blk) 71110616 Bolt Fin Hex 3/8-16 unc x 1 19131610 Washer 13/32 x 3/4 x 10 Ga. 145006 Clip Push In Hinged...
- Page 44 TRACTOR - - MODEL NUMBER 917.275764 DECALS PART DESCRIPTION 193307 Decal Oper. Instr. 193563 Decal Replacement 186280 Decal Hood, R.H. 186281 Decal Hood, L.H. 138047 Decal Battery 133644 Decal Customer Maintenance 191777 Decal HP Engine 172331 Decal Mower Srs 186282...
- Page 45 TRACTOR - - MODEL NUMBER 917.275764 LIFT ASSEMBLY 13 _ PART DESCRIPTION 159460 Washer Asm Inner Spring W/ Plunger 159471 Shaft Asm. Lift 105767X Pin Groove 12000002 E Ring #5133-62 19211621 Washer 21/32 x 1 x21 Ga. 120183X Bearing Nylong...
- Page 46 TRACTOR - - MODEL NUMBER 917.275764 MOWER DECK i147 23 24 118_ 42 D man-t-path stlt...
- Page 47 TRACTOR - - MODEL NUMBER 917.275764 MOWER DECK PART DESCRIPTION 165892 Mower Deck Assembly, 42" STD533107 Bolt 138017 Bracket Assembly, Sway Bar, Front 165460 Bracket Sway Bar 38/42" Deck STD624008 Retainer Spring 178024 Bar Sway Deck 850857 Bolt, Hex 3/8-24 x 1.25 Gr. 8...
- Page 48 TRACTOR PEERLESS TRANSAXLE - - MODEL NUMBER LTH2000 .iJ ... 13 • - - MODEL NUMBER 917.275764 " _ ... " _ -191 -190 --208 _ 28 185-- 184--@ 182--_'...
- Page 49 Actuator Rod 774869 Axle 16.812 774688 Axle 11.625 778378 Spur Gear 18T 778379 Spur Gear 81T 780195 Washer .7501D .062W 776440 Brakeshaft - - MODEL NUMBER 917.275764 PART 786196 792201 792154 788088A 792141 792200 792199 792184 792193 792198 780096 786162 792046...
- Page 50 524 @ 1019 LABEL KIT 1058 OWNER'S 1036 EMISSION LABEL 48 SHORT BLOCK 238 ® 1022 - - MODEL NUMBER 917.275764 NUMBER 31P777, TYPE NUMBER 0602-E2 1270 7591 684_11 ___ 584_ 1264I_ MANUAL 126_ ! 1329 REPLACEMENT ENGINE 1095 VALVE GASKET...
- Page 51 462 _ 1266A< 121 CARBURETOR OVERHAUL 104g 1370 276_ 634_ 95_93@ 106117_ 6170 - - MODEL NUMBER 917.275764 NUMBER 31P777, TYPE NUMBER 0602-E2 697 _ _'118 ,_ 74? 240_ 1044_ 997® 1266 0 1266A <_) 3o6 _ 1040 1091 127 O...
- Page 52 Kit-Idle Mixture 691636 Screw (Throttle Valve) 495800 Kit-Idle Speed 690525 OPin-Float Hinge 231855 OValve-Float Needle 690577 OSeat-lnlet - - MODEL NUMBER 917.275764 NUMBER 31P777, TYPE NUMBER 0602-E2 PART 692344 (Magneto Side) 694352 697228 697241 791888 Head 695005 691750 494379 494381...
- Page 53 Dipstick/Tube Assembly 692424 Terminal-Spark Plug 690968 ,+Seal-Valve 393456 Wire/Connector-Alternator 691108 Screw (Rocker Cover) 690589 .SeaI-O Ring (Oil Pump Cover) - - MODEL NUMBER 917.275764 NUMBER 31P777, TYPE NUMBER 0602-E2 PART 694393 499613 697015 699986 495933 690192 691326 1005 699043 1017...
- Page 55 SUGGESTED GUIDE FOR SIGHTING ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL down the face of slopes, never across the face. Do not mow WARNING: To avoid serious injury, operate your tractor up and slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control.
- Page 56 ©Sears Brands, ®Registered Trademark / TMTrademark / SMService Mark of Sears Brands, LLC ® Marca Registrada / TMMarca de Fabrics / SMMarca de Servicio de Sears Brands, LLC MCMarque de commerce / MDMarque deposee de Sears Brands, LLC 401206 09.13.05 Printed in U.S.A.
Need help?
Do you have a question about the 917.275764 and is the answer not in the manual?
Questions and answers
H0w to release the break if you just want to move the mower when it's not running?
To release the brake on a Craftsman mower with part number 917.275764 when it is not running, ensure the engine is off and the parking brake is set. Then, disengage the parking brake manually by slowly releasing the brake pedal. Do not attempt to engage or disengage the freewheel lever while the engine is running.
This answer is automatically generated
Dies when I engage the blades.
Your Craftsman 917.275764 may die when you engage the blades due to a faulty operator-safety control system. This can happen if there is an issue with the wiring, switches, or connections. Check these components, and if the problem continues, contact a qualified service center.
This answer is automatically generated