Briggs & Stratton NAX 400C Manual
  1. Manuals
  2. Brands
  3. Briggs & Stratton Manuals
  4. Chainsaw
  5. NAX 400C
  6. Manual

Briggs & Stratton NAX 400C Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
NAX 400C
1

Advertisement

Table of Contents
loading

Related Manuals for Briggs & Stratton NAX 400C

Summary of Contents for Briggs & Stratton NAX 400C

  • Page 1 NAX 400C...
  • Page 3 CHAIN SAW NAX 400C...

  • Page 4: Chain Saw Construction And Overview Drawings

    CONSTRUCTION OF CHAIN SAW AND PREVIEW DRAWINGS Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5...
  • Page 5 Fig. 6 Fig. 7 Fig. 9 Fig. 8 Fig. 10...
  • Page 6 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 15...
  • Page 7 Fig. 16 Fig. 17 Fig. 18 Fig. 19 Fig. 20 Fig. 21...
  • Page 8 Fig. 22 Fig. 23 Fig. 24 Fig. 25 Fig. 26 Fig. 27...
  • Page 9 Fig. 28 a Fig. 29...
  • Page 10 Fig. 30...

  • Page 11: Table Of Contents

    Original operation manual, edition 1/2020 Translation of the original operation manual from polish language This manual should be treated as an integral part of the device. It should be stored in the place provided for it so that it is easily accessible.

  • Page 12: Technical Data

    TECHNICAL DATA CIRCULAR COMBUSTION SAW Type, model NAX 400C Engine TT-1E46F series BS Fuel mix 40: 1 (4 l of gasoline for every 100 ml of two-stroke oil) Fuel tank capacity 500 cm Mix oil (recommended) Briggs & Stratton for two-stroke engines...

  • Page 13: Description Of Graphic Pages And Pictograms

    DESCRIPTION OF GRAPHIC PAGES AND PICTOGRAMS Pictograms page 2.A Attention! Danger. Exercise special caution. Important! Read the instructions and follow the warnings. Risk of fire or explosion. Gasoline is highly flammable. Keep out of the reach of children. It is prohibited to work in the rain. Note: Exhaust gases are harmful to health.
  • Page 14 SAFETY DURING WORKING WITH FUEL  The internal combustion engine is designed to run on gasoline or a fuel mixture (see type of fuel in the device's technical data).  Gasoline should be stored only in specially prepared containers (canisters). ...

  • Page 15: Detailed Safety Regulations

     Store the unused equipment out of the reach of children. Do not allow people not familiar with the tool or this manual to use the equipment. Internal combustion tools and equipment are dangerous in the hands of untrained users. ...
  • Page 16  Safety devices (e.g. cutting unit cover, housing, handle, engine switch) are in good technical condition and work properly;  Before adjustment, cleaning, maintenance, switch off the engine.  Do not use the device when other people, especially children or pets, are nearby. ...
  • Page 17  When cutting through, always use the buttress as a fulcrum. Holding the chainsaw by the main handle, guide it with the auxiliary handle.  If it is not possible to cut the material at once, pull the saw back slightly, move the buttress and continue cutting by slightly raising the main handle of the saw.

  • Page 18: Safety And Producer's Liability

    SAFETY AND PRODUCER'S LIABILITY Any use of the chain saw, other than described in this manual is considered improper and the manufacturer is not liable for any damage or damages resulting from such a procedure. Proper use also includes respecting the operating, maintenance, storage and repair conditions established by the manufacturer. To prevent accidents, all safety precautions and hazard avoidance must be followed.

  • Page 19: Construction Of A Chainsaw

     Use extreme caution when cutting small branches and trees, as thin material can get stuck in the saw chain and hit the operator or throw him off balance.  When cutting stressed boughs, be careful not to be hit when the stress in the wood fibers is reduced. ...
  • Page 20 Use these guidelines to be careful not to make a mistake. Designations of the symbols. (Fig. 8) Hole for refilling the fuel mixture. Place: fuel tank housing Fig. 1, point 10. Hole for topping up oil to the chain. Place: fuel tank housing Fig. 1, point 11. Switch tip.

  • Page 21: Starting The Saw

    Check chain lubrication system. After starting the engine, use the gas control lever to set the maximum speed and check that the chain is spraying oil as shown on Fig. 9. The oil flow for chain lubrication can be adjusted by inserting a screwdriver into the bottom slot on the clutch side (Fig. 10). The flow should be adjusted according to the operating conditions.

  • Page 22: Operation

    It is extremely important that the brake is checked for proper operation before each use and that the chain is sharp in order to maintain the correct level of protection against the chainsaw bouncing back. Removing protective devices, improper maintenance, or replacing the guide bar or chain with the wrong equivalent can increase the risk or cause serious injury.
  • Page 23 To reach the air filter, unhook the tabs 1 (Fig. 20) and remove the air filter cover 2 (Fig. 20). Then unscrew the wing nut holding the air filter 1 (Fig. 21) and remove the air filter 2 (Fig. 21). The air filter should be disassembled, washed with gasoline and dried, and replaced if necessary.

  • Page 24: Transport

    CHAIN SHARPENING The cutting tool should always be clean and sharp to ensure efficient and safe work. Working with a chain saw with a blunt chain causes faster wear of the guide chain and chain drive wheel, and in extreme cases can lead to chain breakage. That is why it is important to sharpen the chain in time.

  • Page 25: Storage

    STORAGE Keep the chain saw in a dry, ventilated and safe place out of reach of children. If the chain saw is not in use, it should be stored clean, on a flat and dry surface. If the break in operation is longer than 3 months it is necessary to: ...

  • Page 26: Review And Diagnosis Of Problems

    REVIEW AND DIAGNOSIS OF PROBLEMS INSPECTIONS Prior to After work After each Once In case of Inspections Monthly each use or daily refueling a week damage required visually check (condition, leaks) Entire Machine clean Throttle switch and lock, combination test switch test Chain brake...

  • Page 27: Device Assembly Diagrams

    TROUBLESHOOTING Problem Possible cause Solution Difficulties in starting a cold Low fuel. Check the fuel level and add fuel if necessary. engine. Spark plug flooded or damaged. Check, clean or replace the spark plug. No spark on the spark plug. Replace the spark plug with a new one.

  • Page 28: Declaration Of Conformity

    DECLARATION OF CONFORMITY        ...
  • Page 29 WARRANTY Dear Sir or Madam, Thank you for purchasing our product and congratulations on your right choice. The device that you bought was designed and manufactured according to the latest technologies and represents global standards of quality and reliability, while being environmentally friendly. We remind you to carefully read the commissioning and operation procedures before using the device;...

  • Page 30: Warranty Conditions

    WARRANTY CONDITIONS 1. NAX guarantees smooth operation of the device in accordance with the technical and operational conditions described in the User Manual. 2. The device is granted a 36-month warranty to the consumer (i.e. a natural person making a legal transaction with the entrepreneur not directly related to its business or professional activity) and a 12-month warranty when purchased by the entrepreneur (i.e.

  • Page 31: Warranty Card

    Warranty card ………………………………………………………………….. ……………………………………………………………………………………….. Equipment name * Model * …………………………… ………………………………………… ………………………………………… Date of sale * Device serial number * Engine serial number I declare that I have read the User Manual and the Warranty Card. I received the purchased equipment in working order, complete, along with the proof of purchase. Legible signature of the buyer ....................

Table of Contents