Installation; Wartung; Maintenance - Grohe ESSENCE NEW 19 408 001 Installation Instructions Manual

Table of Contents

Advertisement

D
Technische Daten
• Durchfluss bei 3 bar Fließdruck:

Installation

Einbauschablone entfernen, siehe Klappseite II, Abb. [1].
Rohrleitungssystem vor und nach der Installation
gründlich spülen (DIN 1988/DIN EN 806 beachten)!
Mengenbegrenzer
Diese Armatur ist mit einer Mengenbegrenzung ausgestattet.
Damit ist eine stufenlose, individuelle Durchflussmengen-
begrenzung möglich. Werkseitig ist der größtmögliche
Durchfluss voreingestellt.
In Verbindung mit hydraulischen Durchlauferhitzern ist
der Einsatz der Durchflussmengenbegrenzung nicht zu
empfehlen.
Zur Aktivierung siehe Klappseite II, Abb. [2].
Kalt- und Warmwasserzufuhr absperren.
I. Rosette und Hebel montieren, siehe Abb. [3], [4] und [5].
1. Kappe (A) aufstecken, siehe Abb. [3].
2. Dichtung (B1) einfetten und Rosette (B) aufschieben,
siehe Abb. [4].
3. Isoliereinsatz (C) aufstecken und mit Schraube (D)
befestigen, siehe Abb. [5].
4. Hebel (E) aufstecken, mit dem lose eingeschraubten
Gewindestift (F) mit Innensechskantschlüssel 3mm
befestigen und Stopfen (G) einsetzen.
Falls sich die Rosette nicht weit genug auf die Kappe schieben
lässt, muss zusätzlich eine Verlängerung eingebaut werden
(siehe Ersatzteile Klappseite I, Best.-Nr.: 46 627 = 25mm).
GB
Technical data
• Flow rate at 3 bar flow pressure:
Installation
Remove the fitting template, see fold-out page II, Fig. [1].
Flush piping system prior and after installation of fitting
thoroughly (Consider EN 806)!
Flow rate limiter
This fitting is equipped with a flow rate limiter, permitting an
infinitely variable individual reduction in flow rate. The highest
possible flow rate is set at the factory before dispatch.
The use of flow rate limiters in combination with hydraulic
instantaneous heaters is not recommended.
For commissioning, see fold-out page II, see Fig. [2].
Shut off hot and cold water supply.
I. Install escutcheon and lever, see Figs. [3], [4] and [5].
1. Attach cap (A), see Fig. [3].
2. Grease seal (B1) and push on escutcheon (B), see Fig. [4].
3. Attach insulating insert (C) and secure with screw (D), see
Fig. [5].
4. Attach lever (E), secure by tightening the loosely fitted set
screw (F) using an 3mm allen key and insert plug (G).
If the escutcheon will not slide far enough onto the cap, you
must additionally install an extension (see replacement parts
fold-out page I, Prod. no.: 46 627 = 25mm).
II. Install spout, see Figs. [6], [7] and [8].
1. Determine dimension "Y" from the leading edge of built-in
fitting housing to face of tiles, see Fig. [6].
1
II. Auslauf montieren, siehe Abb. [6], [7] und [8].
1. Maß „Y" von der Oberkante des Unterputz-Gehäuses bis
zur Fliesenoberkante ermitteln, siehe Abb. [6].
2. Anschlussnippel (H) ablängen, so dass sich ein Gesamtmaß
ca. 5 l/min
von „Y" + 25mm ergibt.
3. Auslauf (I) mit Innensechskantschlüssel 2,5mm an
Rosette (I1) befestigen, siehe Abb. [7].
4. Anschlussnippel (H) mit einem 12mm Innensechskant-
schlüssel so in das Unterputz-Gehäuse einschrauben, dass
sich ein Einbaumaß von 7mm ergibt. Auslauf (I) mit
einem 2,5mm Innensechskantschlüssel von unten
befestigen, siehe Abb. [8].
Kalt- und Warmwasserzufuhr öffnen und Anschlüsse auf
Dichtheit prüfen.
Funktion der Armatur prüfen, siehe Abb. [9].

Wartung

Alle Teile prüfen, reinigen, evtl. austauschen und mit
Spezialarmaturenfett einfetten.
Kalt- und Warmwasserzufuhr absperren.
I. Kartusche, siehe Klappseite II, Abb. [10].
Montage in umgekehrter Reihenfolge.
Einbaulage beachten!
Beim Einbau der Kartusche auf richtigen Sitz der
Dichtungen achten.
Verschraubung (J) einschrauben und fest anziehen.
II. Mousseur (K), siehe Klappseite II, Abb. [10].
Montage in umgekehrter Reihenfolge.
Ersatzteile, siehe Klappseite I (* = Sonderzubehör).
Pflege
Die Hinweise zur Pflege dieser Armatur sind der beiliegenden
Pflegeanleitung zu entnehmen.
2. Cut connection nipple (H) so that the installation dimension
is "Y" + 25mm.
3. Fasten spout (I) to escutcheon (I1) using a 2,5mm allen key,
see Fig. [7].
approx. 5 l/min
4. Using an 12mm allen key, screw connection nipple (H) into
the built-in fitting housing until the installation dimension
is 7mm. Tighten spout (I) from below using an 2,5mm allen
key, see Fig. [8].
Open hot and cold water supply and check connections
for watertightness!
Check fitting for correct operation, see Fig. [9].

Maintenance

Inspect and clean all parts, replace as necessary and lubricate
with special grease.
Shut off hot and cold water supply.
I. Cartridge, see fold-out page II, Fig. [10].
Assemble in reverse order.
Observe the correct installation position!
When installing the cartridge, ensure that the seals are
correctly seated.
Screw in and tighten screwing (J).
II. Flow control (K), see fold-out page II, Fig. [10].
Assemble in reverse order.
Replacement parts, see fold-out page I (* = special
accessories).
Care
For directions on the care of this fitting, refer to the
accompanying Care Instructions.

Advertisement

Table of Contents
loading

This manual is also suitable for:

Essence new 19 967Essence new 19 408

Table of Contents