Table of Contents
Advertisement
Safety Information, General Notes & Lead Free Requirements
1
Safety Instructions
1.1
General Safety
Safety regulations require that during a repair:
Connect the unit to the mains via an isolation transformer.
Replace safety components, indicated by the symbol
only by components identical to the original ones. Any
other component substitution (other than original type)
Safety regulations require that after a repair, you must return
the unit in its original condition. Pay, in particular, attention to
the following points:
Route the wires/cables correctly
mounted cable clamps.
damage.
Check the electrical DC resistance between the mains
plug and the secondary side:
1. Unplug the mains cord, and connect a wire between
the two pins of the mains plug.
2. Set the mains switch to the 'on' position (keep the
mains cord unplugged!).
3. Measure the resistance value between the mains
plug and the front panel, controls, and chassis
bottom.
4. Repair or correct unit when the resistance
5. Verify this, before you return the unit to the customer/
user (ref. UL-standard no. 1492).
6. Switch the unit 'off', and remove the wire between the
two pins of the mains plug.
1.2
Laser Safety
This unit employs a laser
may remove the cover, or attempt to service this device (due
to possible eye injury).
Laser Device Unit
T
y
p
e
Wavelength
Output Power
Beam divergence
LASER PRODUCT
Note: Use of controls or adjustments or performance of
procedure other than those speci ed herein, may result in
:AIGalnN(BD)
:AIGalnP(DVD)
: AIGalnP(CD)
: 650 nm (DVD)
:
7
8
0
n
m
V (
C
D
C /
D
)
:
405nm(BD)
: 20 mW
(
D
V
D
+
R
W
w
t i r
n i
) g
:
0
8 .
m
W
(
D
V
D
e r
a
d
n i
) g
:
0
3 .
m
W
V (
C
D
C /
D
e r
a
d
n i
) g
: 60 degree
CLASS 1
F
g i
u
e r
2
1 -
A
2
Warnings
2.1
General
All ICs and many other semiconductors are susceptible to
electrostatic discharges (ESD,
,
during repair can reduce life drastically. Make sure that,
during repair, you are at the same potential as the mass
of the set by a wristband with resistance. Keep
components and tools at this same potential.
Available ESD protection equipment:
–
Complete kit ESD3 (small tablemat, wristband,
4822 310 10671.
–
Wristband tester 4822 344 13999.
Be careful during measurements in the live voltage
section. The primary side of the power supply, including
the heatsink, carries live mains voltage when you
connect the player to the mains (even when the
player is 'off'!). It is possible to touch copper tracks and/
or components in this unshielded primary area, when
you service the player. Service personnel must take
precautions to prevent touching this area or components
in this area. A 'lightning stroke' and a stripe-marked
printing on the printed wiring board, indicate the primary
side of the power supply.
Never replace modules, or components, while the unit is
'on'.
2.2
Laser
The use of optical instruments with this product, will
Only quali ed service personnel may remove the cover or
attempt to service this device, due to possible eye injury.
Repair handling should take place as much as possible
with a disc loaded inside the player.
T
shield:
CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING UNDGÅ UDSÆTTELSE FOR STRÅLING
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES UNNGÅ EKSPONERING FOR STRÅLEN
VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN
VARO! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN
VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN
DANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM
ATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D'OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU
5-1
). Careless handling
Figure 2-2
Advertisement
Table of Contents
