Related Manuals for TMG TMG-SFM72
Summary of Contents for TMG TMG-SFM72
- Page 1 TMG-SFM72 PRODUCT MANUAL v.2023.07.04 72“ SKID STEER FLAIL MOWER www.tmgindustrial.com TOLL FREE: 1-877-761-2819...
-
Page 2: Table Of Contents
EASON ................................. 10 YDRAULIC YSTEM ................................... 10 ORQUE SPECIFICATION ..................................11 & C ..............................11 PECIFICATIONS APACITIES PARTS LIST ..................................12 TMG-SFM72 F ..........................12 LAIL OWER SSEMBLY TMG-SFM72 C ............................15 OUPLING SSEMBLY TMG-SFM72 H ..........................16 YDRAULIC COMPONENTS www.tmgindustrial.com... -
Page 3: Important Safety Information
Your Safety YOU are responsible for the SAFE operation and maintenance of your TMG Skid Steer Flail Mower. YOU must ensure that you and anyone else who is going to use, maintain or work around the Skid Steer Flail Mower be familiar with the using and maintenance procedures and related SAFETY information contained in this manual. -
Page 4: Equipment Safety Guidelines
- Wet weather gear - Hearing Protection 6. Install and secure all guards before starting. 7. Wear suitable ear protection for prolonged exposure to excessive noise. 8. Turn machine off, stop and disable engine, remove ignition key and place in your pocket, set park brake and wait for all moving parts to stop before servicing, adjusting, repairing, or unplugging. -
Page 5: Safety Training
10. In addition to the design and configuration of this implement, including Safety Signs and Safety Equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of the machine. Refer also to Safety Messages and operation instruction in each of the appropriate sections of the skid steer and machine manuals. -
Page 6: Safety Decals
Safety Decals Preparation Never use the machine until you have read and completely understand this manual, the skid steer tractor Operator's Manual and each of the Safety Messages found on the safety signs on the skid steer tractor and machine. Personal protection equipment including hard hat, safety glasses, safety shoes, and gloves are recommended during assembly, installation, operation, adjustment, maintaining, repairing, removal, cleaning, or moving the unit. -
Page 7: Hydraulic Safety
Follow good shop practices. Keep service area clean and dry. Be sure electrical outlets and tools are properly grounded. Use adequate light for the job at hand. Make sure there is plenty of ventilation. Never operate the engine of the towing vehicle in a closed building. The exhaust fumes may cause asphyxiation. -
Page 8: Transport Safety
Wear proper hand and eye protection when searching for a high-pressure hydraulic leak. Use a piece of wood or cardboard as a backstop instead of hands to isolate and identify a leak. If injured by a concentrated high-pressure stream of hydraulic fluid, seek medical attention immediately. Serious infection or toxic reaction can develop from hydraulic fluid piercing the skin surface. - Page 9 Drive up to the Flail Mower while aligning the mounting components, and hook up into the mount. Secure the mounting: Drive into the mounting frame. Seat the top of the face plate into the frame of the Flail Mower. Raise the loader and tilt the face plate until it is fully mated. Engage the lock pins to secure the Flail Mower to the loader.
-
Page 10: Maintenance
MAINTENANCE Before Every Use Check that all fasteners (nuts, bolts, pins, keepers) are in their right place and are tight. Inspect and replace any worn, torn or missing safety decals. Investigate the location of any oil leaks and repair. Lubricate all joints with lithium grease. Every Week Check the condition of the blades. -
Page 11: Specification
The tables shown below give correct torque values for various bolts and cap screws. Tighten all bolts to the torques specified in chart unless otherwise noted. Check tightness of bolts periodically, using bolt torque chart as a guide. Replace hardware with the same strength bolt. -
Page 12: Parts List
PARTS LIST TMG-SFM72 Flail Mower Assembly www.tmgindustrial.com 12 / 16 TOLL FREE: 1-877-761-2819... - Page 13 Part No. Ref. Part Description GB/T 5782 Bolt M16*120 GB/T 97.1 Washer 16 LM180.27 Bushing LM180.25 Bushing for wheel LM180.10 Wheel Φ220*75 GB/T 6182 LOCK NUT M16 WLF130.4 Axle adjusting sleeve 02 WLF130.3 Axle adjusting sleeve 01 JB／T 7940.1-1995 Greaser M8 WLF130.2 Wheel arm weldment DIN 11023...
- Page 14 Part No. Ref. Part Description GB/T 5783 Bolt M8*25 WLF130.9 Protection Plate 01 WLF130.26 Bushing M6X1-6X4 Lock nut connector WLF130.25 Pipe for grease Φ6*Φ4 WLF130.24 Tension rollers assemble 46-1 WLF130.24.1 Tension plate weldment 46-2 WLF130.24-2 Tension Roller 46-3 GB/T 276 Bearing 6005-Z 46-4 WLF130.24-3...
-
Page 15: Tmg-Sfm72 Coupling Assembly
TMG-SFM72 Coupling Assembly Part No. Ref. Part Description 58-1 GB/T 1387.1 Oil seal 40*55*8 58-2 LM180.17-1 Coupling housing 58-3 GB/T 276 Bearing 6208-Z 58-4 WLF130.30-1 Coupling shaft 58-5 GB/T 893.1 Circlip 80 58-6 JB／T 7940.1-1995 Greaser M8 www.tmgindustrial.com 15 / 16... - Page 16 TMG-SFM72 Hydraulic components Part No. Ref. Part Description 65-1 LM180.26-1 Connector 01 65-2 AS 568 O RING Φ32.92*3.53 65-3 GB/T 5862 FLAT FACED COUPLERS G1/2 MALE 65-4 GE15LRED Connector 02 65-5 WLF130.27-1 Hydraulic hose: Length:2000mm 65-6 GE10SRED Connector 03 65-7...
Need help?
Do you have a question about the TMG-SFM72 and is the answer not in the manual?
Questions and answers