Advertisement
•
Keep work area clean and well lit
•
Stay alert; watch what you are doing, use common sense
and do not operate the tool when you are tired
•
Take a secure stance; do not overreach, especially on
ladders and stages
•
Ensure that the tool is switched off, before putting it aside
•
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
AFTER USE:
- set the tool down on its rear in an upright position
•
Switch off the tool and disconnect the plug
•
Allow the tool to cool down for at least 30 minutes before
storage
Do not store/leave the tool outdoors
•
•
Store the tool in a dry and locked-up place, out of reach
of children
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Double insulation (no earth wire required)
5 Do not dispose of the tool together with household waste
material
USE
•
On/off switch with temperature settings 6
! check if switch A 2 is in position "0" before
plugging in
- switch on the tool by pushing switch A in desired
position:
8020
I = 50°C, air flow 350 litres/minute
II = 450°C, air flow 350 litres/minute
III = 600°C, air flow 500 litres/minute
8040
I = 50°C + air flow 250-500 litres/minute
II = 50°C ... 650°C, air flow 250-500 litres/minute
- when using it for the first time, some smoke may emit
from the tool; this is normal and will soon cease
- switch off the tool by pushing switch A in position "0"
•
Temperature setting
! there is a tolerance on the indicated temperatures
50...90°C: max 90°C
less than 300°C: ±20%
more than 300°C: ±10%
8020
- use dial wheel M to select the desired temperature
setting
- use table 6 for reference
8040 7
- set desired target temperature in steps of 10°C by
pressing buttons B briefly
- pressing buttons B constantly increases/decreases
the target temperature continuously until the buttons
are released or the minimum/maximum temperature is
reached
- after the target temperature is set, display D shows
flashing arrows until the desired temperature is reached
(in position "II" only)
- the target temperature will be stored in the memory of
the tool, so that each time after switching on the tool
heats up to the last selected target temperature
•
Air flow setting 8 (8040)
- set desired air flow in steps of 50 l/min by pressing
buttons C briefly
- display D shows the actual air flow setting in a bar
graph
Memory setting 9 (8040)
•
- to select one of the four stored memory settings press
button P
- to store a temperature and air flow setting press
button P to select a memory location, set the desired
temperature and airflow, and press and hold button N
to store the setting
•
General use
- determine the right temperature by testing out on an
inconspicuous part of the workpiece; start with a low
temperature setting
- the temperature drops as the distance between the air
outlet/nozzle and the workpiece increases
- the temperature required depends on the material to
be worked on
•
Stationary use q
- set the tool down on its rear in an upright position
- make sure the surface is clean and dustfree; polluted
air damages the motor
- make sure the air flow is directed away from you
- secure the cord to prevent pulling down the tool
- do not touch the air outlet/nozzle
- make sure nothing drops into the air outlet/nozzle
- carefully hold the tool with one hand while switching it
off with the other hand, and then allow it to cool down
Holding and guiding the tool w
•
- hold the tool with one hand
- keep ventilation slots F 2 uncovered
•
Standard accessories 2
- glass protection nozzle G (for deflecting air flow)
- round nozzle H (for concentrating air flow)
- reflector nozzle J (for reflecting air flow)
- reduction nozzle K (for concentrating air flow)
NOTES:
- all application examples (except removing paint
next to glass) can be performed without accessories;
however, using the appropriate accessory simplifies the
work and significantly improves the quality of the results
- this tool can also be used in combination with
commonly available accessories for heat guns
•
Mounting/removing accessories
- simply fit the accessory onto air outlet L 2
- remove an accessory by pulling it off to the front after it
has cooled down
! mount an accessory only when the air outlet is
cold, when the switch is in position "0" and when
the plug is disconnected
- use nozzle release ring E for easy removing hot nozzles
e
•
Constant heat control (overload protection)
Protects heating element from damage when tool is
overloaded without having to stop it and/or let it cool
down for a period of time
- when the temperature gets too high, the heating
element switches itself off, while the motor continues to
run and produces cold air
- when the temperature has dropped sufficiently (taking
only a few seconds), the heating element will be
switched on automatically
! when the tool is switched off after working at a
high temperature setting, and switched on again
after a short break, it may take a while before the
heating element reaches the desired temperature
8
Advertisement
