Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Hokuto Electronic FLASH1
Summary of Contents for Hokuto Electronic FLASH1
- Page 1 Flash memory MCU On-board Programmer FLASH1 User’s Manual Windows95, 98 Please read this carefully before using the product F-ZTAT is a trademark of Renesas Electronics. Windows 95 and Windows 98 are products of Microsoft Corporation. HokutoDenshi Co., Ltd. REV.2.1.0.0...
- Page 2 Contents GENERAL PRECAUTION FLASH1 OUTLINE ⚫ ONTENTS ⚫ HE PROVIDED INCLUDES ⚫ PECIFICATIONS FLASH1 T ⚫ HE IMAGE OF THE CASE ⚫ ATTERY OLDER UIDANCE - CONNECTOR & CABLE – PREPARATION 1 FLASH1 I ⚫ NTERFACE IRCUIT IAGRAM ⚫ EFERENCE...
-
Page 3: General Precaution
LIMITED GUARANTEE Hokuto Denshi Co., Ltd. guarantees that the FLASH1 can be used by the usage described in this manual by Hokuto Denshi Co., Ltd., and guarantees that FLASH1 has been produced correctly and is free of any defects per the products specification. - Page 4 FLASH1 Outline FLASH1 has been designed to program flash memory MCU, made by Renesas Electronics. This FLASH1 circuit management at writing to Boot mode memory is fully automated. Writing to the target Start programming after erasing internal ROM MCU from the user's PC can be carried out without...
- Page 5 Serial seal on front box FALSH1 Back of the case. Inside of the battery box. ⚫ FLASH1 The image of the case ＬＥＤ state USER VCC When power is supplied from From PC target board, this LED lights up. RS232C When VPP （...
- Page 6 (-) of the battery holder could come into contact with positive terminal (+) inside of the flexible insulating label as shown in the diagram below. It causes electrical short-circuit. Please do not use the batteries described above. Electrical short-circuit may cause smoke and fire. User’s Manual HokutoDenshi FLASH1 －5－...
-
Page 7: Connector & Cable
Please note that MD port RESET is supposed to be driven with open collector. Send FLASH1 reset signal to MCU reset port with no delay. Connect manual RESET with AND parallel circuit or Wired-or. TXD, RXD must be transmitted at TTL level. RS232C converted signals may be arranged into reverse. -
Page 8: Target Board
25pins 9pins 25pins Caution! :The no.4 & 5 lines of the programmer side must be connected appropriately, because of the importance for the steady control form “FLASH1 for Windows”. ⚫ Signals Between FLASH1 and Target Board FLASH1 side Target board side... - Page 9 After the completion window, the window below appears when the PC requests reset, appears when all the files for FLASH1 control select “はい” to make installation effective. software are set up appropriately, click the button “Close” to end FLASH1 the installation.
-
Page 10: Select Parameters
Help in FLASH1 for Windows -contents- ●At Beginning●Feature●Specifications●Connections and Advices●Preparation of Target Board ●Basic Operation●Writing Flow of FLASH1●Timing Chart in Start of Boot Mode●Error Messages Lack of Vpp Voltage/Bit Rate Adjustment Error/ Invalid Code Accepted/ Erase Error/Flash Memory Erase Error/Invalid File Format/Data Transmission Error Sample programs are not automatically copy at the installation of the control software. - Page 11 Other Expendable Supplies Expendable Supplies Name Notes AC 100 volt Adapter Verified only in Japan FLASH1 Target Cable Available for FLASH MATE 12V1 Please visit our web site for the latest information. https://www.hokutodenshi.co.jp For technical support: support@hokutodenshi.co.jp USER'S MANUAL FLASH1 –...
Need help?
Do you have a question about the FLASH1 and is the answer not in the manual?
Questions and answers