Download Print this page
Martha Stewart ZG-ZP-09-WH-GLD-MS Instruction Manual

Martha Stewart ZG-ZP-09-WH-GLD-MS Instruction Manual

Home office desk

Advertisement

Quick Links

Instruction Manual
Home Office Desk
SKU: ZG-ZP-09-WH-GLD-MS
SKU: ZG-ZP-09-GY-MS
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly
Required. DO NOT ALLOW CHILDREN TO CLIMB
ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware
(where included) to help prevent the unit from tipping and causing accidental injury, instability, death or
damage. The tipping restraint is intended only as a safety measure, it is not a substitute for proper adult
supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Customer Service Email: CustomerExperience@theubiquegroup.com | Phone: 866-552-2810

Advertisement

loading
Need help?

Need help?

Do you have a question about the ZG-ZP-09-WH-GLD-MS and is the answer not in the manual?

Questions and answers

Summary of Contents for Martha Stewart ZG-ZP-09-WH-GLD-MS

  • Page 1 Instruction Manual Home Office Desk SKU: ZG-ZP-09-WH-GLD-MS SKU: ZG-ZP-09-GY-MS ASSEMBLY INSTRUCTIONS Before You Begin: Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching during assembly.
  • Page 2 Safety and Care Advice Important – Please read these instructions fully before starting assembly • Check you have all the • During assembly do not stand • To reduce the components and tools listed on or put weight on the product, likelihood of the following pages.
  • Page 3 Hardware Please check you have all the parts listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more hardware may be supplied than is required. Male Camlock x 54 Female Camlock x 54 Dowel x 26 4*30mm Screw x 9 Drawer slider 14"...
  • Page 4 Using Camlocks Step 1 Step 2 DO NOT OVER TIGHTEN. Connect the male camlock Push the male camlock as directed in the assembly into the entry hole. instructions using a screwdriver . Step 3 Step 4 Insert the female camlock Turn the female camlock as shown in the clockwise with a...
  • Page 5 Parts...
  • Page 6 Assembly Instructions Step 1 Step 2...
  • Page 7 Assembly Instructions Step 3 Step 4 Ball Bearing Slide Slider Runner Ball Bearing Slide Slider Runner...
  • Page 8 Assembly Instructions Step 5 Step 6...
  • Page 9 Assembly Instructions Step 7 Step 8...
  • Page 10 Assembly Instructions Step 9 Step 10...
  • Page 11 Assembly Instructions Step 11 Step 12...
  • Page 12 Assembly Instructions Step 13 Step 14...
  • Page 13 Assembly Instructions Step 15 Step 16...
  • Page 14 Assembly Instructions Step 17 Step 18...
  • Page 15 Assembly Instructions Step 19 Step 20...
  • Page 16 Assembly Instructions Step 21 Step 22...
  • Page 17 Assembly Instructions Step 23 Step 24...
  • Page 18 Assembly Instructions Step 25 Step 26...
  • Page 19 Assembly Instructions Step 27 Step 28...
  • Page 20 Assembly Instructions Step 29 Step 30...
  • Page 21 Assembly Instructions Step 31 Step 32...
  • Page 22 Assembly Instructions Step 33 Step 34...
  • Page 23 Assembly Instructions Step 35 Step 36...
  • Page 24 Assembly Instructions Step 37 Secondary Slider bracket Step 38...
  • Page 25 Assembly Instructions Step 39 Hinge adjustment instructions are on page 3 Step 40...
  • Page 26 Quality and Safety Guidelines • Please follow the static and dynamic weight capacity limits provided on this item. If you are unsure of the weight capacities for this product, email us at customerexperience@theubiquegroup.com or call 866-552-2810. • Please use this item on a stable, level surface only. All table legs should contact the flooring surface when in use.

This manual is also suitable for:

Zg-zp-09-gy-ms