Table of Contents
Advertisement
Quick Links
43" LED TV
Service
Service
Service
Description
Table of Contents........................................................1
Important Safety Notice...............................................2
Revision List........................................................3
1. General Specification..................................................4
2. Operating Instructions.........................................5
2.1 Remote Control..................................................5
2.2 OSD Menus.......................................................7
2.3 Panel Control And Rear Terminal Control............19
3. Input/Output Specification.....................................23
4. Mechanical Instructions........................................26
5. Repair Flow Chart .............................................29
6. PCB Layout .....................................................36
6.1 Main Board .....................................................36
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
Table of Contents
Page Description
6.2 Power Board................................ ...................38
6.3 IR Board..................................................41
6.4 KeyBoard..................................................41
7. Adjustment..............................................................42
7.1 WB Adjustment..............................................42
7.2 Firmware and DDC Instruction..............................43
8. Block Diagram........................................................44
9. Wiring Diagram.......................................................45
10. Schematic Diagram.........................................46
10.1 Main Board...................................................46
10.2 Power Board.................................................54
10.3 IR Board.......................................................58
10.4 KEY Board..................................................59
SAFETY NOTICE
1
LE43B7500
Page
Advertisement
Table of Contents
Related Manuals for Haier LE43B7500
Summary of Contents for Haier LE43B7500
-
Page 1: Table Of Contents
43″ LED TV LE43B7500 Service Service Service Table of Contents Description Page Description Page Table of Contents..……........…..1 6.2 Power Board……..…………………... …..…..38 Important Safety Notice........……..2 6.3 IR Board………….……………..……….…..41 Revision List………………………………………………..3 6.4 KeyBoard……..…………………...…….…..41 1. General Specification........………..4 7. Adjustment..............42 2. Operating Instructions..………………….……...……..5 7.1 WB Adjustment..........42 2.1 Remote Control…………….……...…………...……..5... -
Page 2: Important Safety Notice
Important Safety Notice Proper service and repair is important to the safe, reliable operation of all Haier Company Equipment. The service procedures recommended by Haier and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. -
Page 3: Revision List
Revision List Version Release Date Revision Instructions Customer Model Model Mar.27,2015 Initial release LE43B7500 E43E41NCDL6HNNX... -
Page 4: General Specification
1. General Specification... -
Page 5: Operating Instructions
2. Operating Instructions 2.1 Remote Control... -
Page 7: Osd Menus
2.2 OSD Menus Picture Setup Items Description Personal User can set their favorite setting. Vivid For Enhances picture contrast and sharpness. For standard picture settings. Recommended for home Standard Smart Picture entertainment. Decrease backlight level to save the power For viewing film-based content. Most suitable for Movie viewing in a theater-like environment. - Page 8 Audio Setup Items Description Standard Suitable for spoken dialog. Music Ehance treble and bass Speech Ehance treble and keep the bass at medium level Smart Sound Personal Adjust sound mode as per personal requirement. Sound Mode can also be accessed by pressing the S.MODE button on the remote control.
- Page 9 Features Setup Items Description Select an OSD menu language can be displayed. Default English is selected as menu Menu Language language. Select a Teletext language in TTX mode. West: Western Europe TTX Language East: Eastern Europe Russian: Russian Arabic: Arabic Resize the aspect ratio of the picture for optimum viewing.
- Page 10 On : TV will turn on daily at specified time with specified channel / source. Once : TV will turn on only once at specified time and channel/source and resets to Off. Timer: Set turn on/off time Power On Setting: Select channel/source when turn on TV Power Off Timer : Turn off the TV at the specified time.
- Page 11 Channel Setup This setup is available in TV mode only. Items Description TV automatically searches for the channel in the available frequency band and stores sequentially. Select TV menu. Auto Search Select Auto search and press OK key or ► arrow key to tune channels automatically and store.
- Page 12 Manual search description 1. Select TV menu and select Channels. 2. Select Manual Search and press OK key or ►arrow key to get Manual search sub-menu. 3. Select Start Frequency to input frequency you want to start 4. Select End Frequency to input frequency you want to end 5.
- Page 13 Hotel Model Please press "Menu +100108+ Back " key to enter Hotel menu. Items Decsription Hotel Mode Operation Set Hotel model on/ off. Max Volume Set max volume limited. This option allows you to set Max Vloume level. Volume Default Select default volume for hotel mode reset.
- Page 14 USB Media Center TV USB port can be used to view JPEG photos, play mp3 music and Video files,and read text present in USB devices. Entering to USB Media Press USB key on remote to get USB Media menu as shown above Or Press the Source key and keys on remote and select USB source to get USB Media menu as shown above.
- Page 15 Viewing Photos 1. Thumbnail of the available images will be displayed on the screen. If no images are displayed then select the folder containing the Photos. 2. Select particular image and press OK key to display it in full screen. Slide show starts automatically when image is viewed in full screen.
- Page 16 USB menu settings for Music play Press Menu key to get following Menu setup shown above. 1. [Play/Pause]: Play/Pause music play. 2. [Repeat]: Select the repeat mode as None, Repeat One, Repeat All. 3. [Random]: Select Shuffle mode as Shuffle Off, Shuffle On. 4.
- Page 17 4. [Smart Picture]: Select the picture mode as Vivid, Standard, Movie, Personal, Eco. 5. [Screen Mode]: Select the screen mode as 4:3, Zoom1, Zoom2, 16:9. 6. [Subtitle Display]: Select the subtitle mode of the movie. 7. [Track]: Select the track mode of the audio. Reading Text files 1.
- Page 18 Format File Extension Codec Data Rate Real media .RM/.RMVB RealVideo 8/9 20Mbit/sec Movie MPEG1/2 .DAT/.MPG MPEG-1/2 Video 20Mbit/sec MPEG4 .AVI /.MP4 H.264 20Mbit/sec Format Note Text Remarks: 1. USB interface of digital multimedia player is not all-purpose. So when some USB devices could not be recognized, the problem is usually not the performance failure but due to device driver.
-
Page 19: Panel Control And Rear Terminal Control
2.3 Panel Control and Rear Terminal Control... -
Page 23: Input/Output Specification
3. Input/Output Specification 3.1 Input Signal Connector D-SUB Pin No. Description Pin No. Description Red Video No Pin Green Video Sync Ground Blue Video Serial Data for DDC Ground H. Sync Red Ground V. Sync Green Ground Serial Clock for DDC Blue Ground HDMI Pin No. - Page 24 3.2 Input Signal Timing PC Input Signal Reference Table Connect a computer to your TV set and set up the computer output signal in accordance with table below. Default computer mode Item Resolution Horizontal Frequency (kHz) Vertical Frequency(Hz) 640 × 480 31.469 59.94 720 ×...
- Page 25 Video Input Signal Reference Table Connect the component signal or HDMI port of video device to your TV set and set up the output signal of the video device in accordance with table below. If your computer display card supports signals of video format then you can set up following output signal. Default Component or HDMI Mode Standard Resolution...
-
Page 26: Mechanical Instructions
4. Mechanical Instructions Step1. Remove the BASE. Step2. Remove the REAR COVER. - Page 27 Step3. Remove the MAIN BOARD、POWER BOARD、BKT IO、SPEAKER. Step4. Remove the BKT_STAND. Step5. Remove the DECO.
- Page 28 Step6. PANEL.
-
Page 29: Repair Flow Chart
5. Repair Flow Chart 1. No power No power (LED “Off”) Check the AC input and Power “On” the power is “ON”? Power board output=5V? Replace the power board Check the IR board and LED Replace the IR board Replace the main board... - Page 30 2. Can’t start Can’t start（LED Blue） Replace the power board Power board output＝12V? Replace the key board Check the power key is under control? Replace the IR board Check the IR receiver is normal? Replace the main board Replace the Power board...
- Page 31 3. Abnormal Display Abnormal Display Reset the source Check the source Enter factory mode to do “EEPROM initial”&“Reset” Replace the main board Check the main board Check the LVDS cable Replace the LVDS cable Check the panel Replace the panel...
- Page 32 4. No display No display (LED Red) Check TV is under control and power Replace the main board on/off by remote control and power key? Check the backlight is “On”? Check the LVDS cable Check the B/L signal is available? Reinsert or replace the LVDS cable Replace main board...
- Page 33 5. Sound problem No sound or sound abnormal Check the audio source connection and the TV system are correct? Reinsert the audio cable or change the TV system Check the TV is muted, adjust the volume or enter the menu to reset? Enter factory mode to do “Reset”...
- Page 34 6. Remote control malfunction Remote Control malfunction Check the remote control battery is Replace the battery not properly placed or no power? Use the other remote controls Replace the remote control Whether the IR board is Replace the IR board abnormal? Replace the main board...
- Page 35 7. OSD is unstable or can’t work normally OSD is unstable or can’t work normally Reconnect the key board Key board connected properly? Replace the button function Buttons are OK? Replace the key board Key board is OK? Enter factory mode to do “Reset” Replace the main board...
-
Page 36: Pcb Layout
6. PCB Layout 6.1 Main Board 715G6686M01002004K... -
Page 38: Power Board
6.2 Power Board 715G6679P02001002M... -
Page 41: Ir Board
6.3 IR Board 715G6721R01002004I 6.4 Key Board 715G6715K01002004I... -
Page 42: Adjustment
7. Adjustment It’s no need to do the ADC, do only white balance. 7.1 WB Adjustment White balance adjustment: Turn on the TV, then press “Menu+8893”, it will achieve the factory mode. Current Source is "AV", and then choose Color temp as Warm / Normal / Cool, use remote control to choose “WD Pattern” for 80 .Then choose the Gain bar to adjust the R/G/B value, the temperature adjustment meet to the required specification range. -
Page 43: Firmware And Ddc Instruction
7.2 Firmware and DDC Instruction 1. Copy software to USB flash disk (root directory). 2. Open the TV 3. Insert USB to TV. Choose “Enter”. After USB SW update OK, TV will reboot. 4. Press “Menu +8893”, then TV will enter factory menu. Check SW version, if OK, then do reset. USB SW updates... -
Page 44: Block Diagram
8. Block Diagram IF+/- ATV&DTV HDMI1 HDMI2 LVDS Panel MST6931 YPbPr CVBS_OUT APA2614 SPEAKER Headphone APA2176... -
Page 45: Wiring Diagram
9. Wiring Diagram Panel 12 Pin 16 Pin CN8101 CN8601 CN9101 4 Pin CN601 30 Pin Power Board CN403 16 Pin 9 Pin CN9100 Main Board CN401 MST6931XP CN701 Key Board 4 Pin 5 Pin CN01 IR Board CN201 Speaker R Speaker L... -
Page 46: Schematic Diagram
10. Schematic Diagram 10.1 Main Board 715G6686M01002004K C704 +5V_Normal 22pF 50V R742 0R05 1/16W +5V_Standby Vout = 0.6x(1+100/13.3)=5.11V R702 R726 100K 1% R728 U706 R725 C726 BL_PWM BL_EN BL_EN 13.3K 1% +5V_Standby PS_ON R762 100OHM1/16W R763 NC/100R 0.1uF 50V 3D_EN Q702 R704 FB703... - Page 47 +5V_Standby H/W Reset R403 D401 1M 1/16W BAV99 HDMI_HP1 HOTPLUG1 HDMI1-SCL HDMI1_DDC_SCL HDMI1-SDA RXO0- HDMI1_DDC_SDA R404 RXO0- HDMI1-CLKP RXO0+ C402 HDMI1_CLK+ RXO0+ HDMI1-CLKN RXO1- HDMI1_CLK- RXO1- HDMI1-RX0P 2.2UF 16V RXO1+ HDMI1_D0+ RXO1+ HDMI1-RX0N RXO2- Q402 HDMI1_D0- 4.7K 1/16W RXO2- HDMI1-RX1P RXO2+ MMBT3906 C403...
- Page 48 RXO0- RXO0- RXO0+ R437 0oHM RXO0+ RXO1- P12V RXO1- RXO1+ Panel Power RXO1+ RXO2- R438 RXO2- RXO2+ +5V_Standby RXO2+ RXOC- RXOC- NC/0oHM PANEL_VCC RXOC+ RXOC+ RXO3- RXO3- Q401 RXO3+ C401 RXO3+ AO3407A R439 100K 1/16W 220N 25V RXE0- R473 C437 R440 RXE0- RXE0+...
- Page 49 YPBPR Video/AV2 IN AV1 IN Close IC side R102 CN102 R148 C102 C147 AV1-CVBS0P AV1-CVBS0P 33 OHM 1/16W 47nF 16V 33 OHM 1/16W 47nF 16V R104 C105 47nF 16V ZD102 33 OHM 1/16W R141 AGND ZD103 R106 75 OHM NC/MLVG0402 C106 NC/MLVG0402 ZD104...
- Page 50 From Main Chip CN501 CN502 HDMI0-RX2P HDMI0_D2+ HDMI0-RX2N SHLD0 SHLD0 HDMI0_D2- HDMI0_D2+ HDMI1_D2+ HDMI0-RX1P R515 4.99ohm 1/16W +/-1% R523 4.99ohm 1/16W +/-1% TMDSD2+ TMDSD2+ HDMI0_D1+ HDMI0-RX1N DGND DSHLD0 SHLD2 DSHLD0 SHLD2 HDMI0_D1- HDMI0_D2- R516 4.99ohm 1/16W +/-1% HDMI1_D2- R524 4.99ohm 1/16W +/-1% HDMI0-RX0P TMDSD2- TMDSD2-...
- Page 51 Silicon Tuner 1K_100MHz/400_400MHz 300mA Tuner Power AGND DGND 3.3V_TUNER +5V_Normal 3.3V_TUNER U101 FB101 Main Chip <--> TU101 ST33WS-2-E VOUT 300mA 1000OHM C129 C130 TUN_IF+ VIFP C127 TUN_IF- VIFM 2.2UF 16V Tuner3.3V 3.3V_TUNER 10uF 10V C128 100UF 16V C101 3.3V SCL_CAN 100N 16V 100N 16V SDA_CAN...
- Page 52 AV_L_OUT# 1.2A Max AMP_AUOUTL0 U601 AV_R_OUT# +5V_Normal AMP_AUOUTR0 Thermal Pad R611 +3.3V_Standby PVDD 10K 1/16W 5% PGND AMP_STB R612 PVCCL R630 Q601 AMP_MUTE 4K7 1/16W 5% MMBT3904 C613 100N 50V NC/100UF 35V NC/100UF 35V C614 C615 100N 50V C619 C612 C617 10K 1/16W 5% C618...
- Page 53 From Main Chip KEY 0-SAR0 KEY 0-SAR0 KEY 1-SAR1 KEY 1-SAR1 IRIN IRIN +3.3V_Standby +3.3V_Standby +3.3V_Standby LEDG LEDG LEDR FB409 LEDR +3.3V_Standby CN401 R456 R457 4K7 1/16W 1% 4K7 1/16W 1% R444 120R/6000mA LED-R NC/10K DGND LED-G R458 IRRX1 POWER_KEY KEY 0-SAR0 LEDG 100OHM...
-
Page 54: Power Board
10.2 Power Board 715G6679P02001002M C9913 CN9903 NC/CONN BR F9902 220PF 250V 5A 250V NC/T5AH/250V FB9901 NR9901 F9901 BEAD SG9901 NR9902 T5AL/250V NC/5A 250V NC/DSPL-501N-A21F C9911 47PF 250V L9901 BD9901 CN9901 12mH L9902 KBJ1008G-FUC 12mH CN9902 470NF 275V C9901 SOCKET NC/CONN 620V RV9901 C9912... - Page 55 D9804 D9802 S8KC S8KC FB9801 FB9802 BEAD BEAD D9801 L9801 FMNS-1106S 240uH Vsin C9820 1UF 450V D9803 R9807 Q9801 SS1060FL C9801 C9802 10R 1/8W 5% TK16A60W 68UF 450V 68UF 450V R9817 C9808 47PF R9805 1.1MR 1% 20K 1/4W R9808 33R 1/8W 5% HS9801 R9802 HEAT SINK...
- Page 56 100K 1/8W 1% C9141 CONN Standby ぃ筿溃 э 120R C9142 1uF 50V Standby 筿溃 HS9101 Haier project 需加入5V DC to DC FB9102 Q9402 ZD9107 LMBT3906LT1G BZT52-B5V1_R1_00001 12VS R9401 U9111 12VS R9406 HEAT SINK 10K 1/8W 1% L9102 +VCC1...
- Page 57 CN8601 +VLED COLD CN9201 NC/CONN HS9202 -VLED-1 R8105 +VLED +VLED R8156 0.1R +24V for PSU function C9114 0 OHM +-5% 1/8W +12V 3D_DB BL_ON/OFF -VLED-2 C8104 R8106 R8 117 C8120 2.2NF 82KOHM +-5% 2WS 82KOHM +-5% 2WS +VLED NC/1NF HEAT SINK For PSU function For D8106 For LPB function...
-
Page 58: Ir Board
10.3 IR Board 715G6721R01002004I LED201 LED_R CN201 U201 Vout R201 15K 1/16W 5% TSOP75438TR CONN C201 2.2uF 10V T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Size TPV MODEL 絬 隔 瓜 絪 腹 02-IR&LED Key Component PCB NAME... -
Page 59: Key Board
10.4 Key Board 715G6715K01002004I SW01 MENU 2.411V 27K 1/10W 1% TACT SW FWRD H1.5MM SW02 INPUT 1.985V 15K 1/10W 1% TACT SW FWRD H1.5MM SW03 VOL+ 1.497V 8K2 1/10W 1% TACT SW FWRD H1.5MM SW04 VOL- 1.070V 4K7 1/10W 1% TACT SW FWRD H1.5MM SW05 0.660V...