Advertisement
3.1.4.
Switch on main supply to charger and the Green lED (fig.2) will light. Press "SET" to begin charging and the Red lED will light.
3.1.5.
When the fast charge is complete the red lED will go out and the green lED will light to indicate trickle charging. The battery pack
is now ready for use.
NOTE: When new, It will take longer to charge initially, and several subsequent charges may also take a little longer then when the
battery pack reaches its optimum performance, the charge time is approximately 1 hour.
3.1.6.
After removing the battery, disconnect the charger from the mains supply and store in the carry case.
WARNING! Ensure you read, understand and apply safety instructions before use.
3.2.
USING ThE WRENCh
3.2.1. Use only impact sockets which are specifically designed for use with an impact wrench. The use of normal Chrome Vanadium sockets
is dangerous since these are more brittle and are liable to shatter.
3.2.2. Fit the socket to the wrench by snapping it onto the square drive (fig.1.1).
3.2.3. Fit the battery pack to the wrench by aligning the tongue on the battery with the groove in the housing and slide into place. Ensure
that the battery pack is firmly located, there is an audible click when it has locked into position.
3.2.4. Select the required direction of rotation. To change direction, push switch (fig.1.3) to the left or right as required. Familiarise yourself
with this operation before use. DO NOT attempt to change the direction of rotation whilst trigger (fig.1.6) is depressed.
When the wrench is not in use, use the same switch to lock off the trigger by placing the switch in the middle position.
3.2.5. When tightening, release the trigger as soon as the impact sound is heard. Take care not to over-torque small fixings.
Note: On critical fixings always check the torque, using a torque wrench, according to the product or vehicle manufacturer's
guidelines.
3.2.6. To affix the side handle, unscrew the lubrication screw (fig.1.2) and screw the handle tightly into the hole, To remove it, reverse
the procedure.
3.2.7. To operate the impact wrench with the side handle attached to the right hand side of the wrench it will be necessary to rotate the front
housing through 180°. To achieve this, remove the four screws from the front housing fig.1.A, rotate the housing 180° and replace the
screws.
4. MAINTENANCE
4.1.
CLEANING
Keep the outer case of the wrench clean and free from grease. DO NOT wash with water or use solvents or abrasives. Use a slightly
dampened cloth.
4.2.
LUBRICATION
Periodically or if the wrench has not been used for some time, remove the lubrication screw (fig.1.2) and inject grease into the
impact mechanism.
For any other service or maintenance, contact your authorised Sealey service agent.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging
should be sorted, taken to a recycle centre and disposed of in a manner which is
compatible with the environment.
When the product is no longer required, it must be disposed of in an environmentally protective way.
1. Remove battery - see section 3.1.1.
2. Dispose of spent battery pack correctly as it contains nickel-Cadmium (niCad).
Dispose of batteries according to local authority guidelines.
ni-Cd
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak's registered compliance scheme. Jack
Sealey ltd's Batteries Producer Registration number (BPRn) is BPRn00705
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
© Jack Sealey limited
Environmental Protection
Battery Removal
Parts support is available for this product. To obtain a parts listing and/or diagram,
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business
Park, Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
www.sealey.co.uk
01284 757500
W e b
sales@sealey.co.uk
01284 703534
email
CP2450.V2
Issue: 1 - 20/02/14
Advertisement
