Sealey CP20VIW Instructions

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instructions protection
1. safety
1.1. General safety.
maintain the impact Wrench and battery in good condition. check moving parts alignment on a regular basis.
9
replace or repair damaged parts. use an authorised service agent and recommended parts only. unauthorised parts may be
9
dangerous and will invalidate the warranty.
ensure the impact Wrench is switched off before installing the battery pack.
9
Keep the impact Wrench and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the Impact Wrench; e.g. ceilings, floors and enclosures may contain electrical items or
9
water piping
ensure battery pack is correctly inserted into the impact Wrench handle and latched in place before attempting to switch on impact
9
Wrench.
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-skid shoes.
9
Keep direction switch in the locked position until the impact Wrench is required for use.
9
Keep children and unauthorised persons away from the working area.
9
Do not use the Impact Wrench where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
Do not allow children to operate the impact Wrench.
8
Do not operate the impact Wrench if any parts are missing as this may cause failure and/or personal injury.
8
Do not hold unsecured work piece in your hand.
8
Do not leave the impact Wrench operating unattended.
8
Do not carry the impact Wrench with your finger on the power switch. Keep direction switch in the locked position.
8
Do not use the impact Wrench for a task it is not designed to perform.
8
Do not operate the impact Wrench when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
Do not get the impact Wrench or battery charger wet or use in damp or wet locations.
8
2. introDuction
the 20V series has been designed to suit users from the DIY enthusiast to the professional. These body only tools offer a one battery fits all
solution with a choice of 20V lithium batteries ranging from 2Ah to 4Ah, meaning costs can be kept down whilst quality remains high. Quality,
stylish, lightweight tools with composite housing and a soft grip making them comfortable and easy to use.
3. specification
model no.. .............................................................. cP20ViW
Batteries ..........................20V 2Ah - 4Ah Li-ion (not supplied)
2Ah ..................................................................... cP20VBP2
3Ah ........................................................................ cP20VBP
4Ah ...................................................................... cP20VBP4
mains charger ...............................CP20VMC (not supplied)
drive ......................................................................... 1/2" Sq.
impact rate ........................................................... 0-3000bpm
no load speed ......................................................0-2200rpm
maximum Torque ............................................ 230Nm(58lb.ft)
Weight ........................................................................... 1.4kg
Vibration ................................................................. 15.87m/s²
uncertainty ................................................................. 1.5m/s²
noise power .................................................................106dB
noise pressure ...............................................................95dB
© Jack sealey limited
instructions for
impact wrench 20V 1/2"sq DriVe 230nm
- boDy only
model no:
Wear protective
Wear ear
gloves
protection
Original Language Version
cp20Viw
fig.1
cP20ViW | issue 1 04/04/18