Related Manuals for tams elektronik WIB-33.2
Summary of Contents for tams elektronik WIB-33.2
- Page 1 Manual WIB-33.2 Carriage lighting with integrated function decoder Colour of lighting: warm white Item no. 53-01340 tams elektronik n n n...
-
Page 2: Table Of Contents
12. EU declaration of conformity.............21 13. Declarations conforming to the WEEE directive......21 © 11/2016 Tams Elektronik GmbH All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, without prior permission in writing from Tams Elektronik GmbH. -
Page 3: Getting Started
WIB-33.2 English 1. Getting started How to use this manual This manual gives step-by-step instructions for safe and correct fitting and connecting of the module, and operation. Before you start, we advise you to read the whole manual, particularly the chapter on safety instructions and the checklist for trouble shooting. -
Page 4: Safety Instructions
English WIB-33.2 2. Safety instructions Mechanical hazards Cut wires can have sharp ends and can cause serious injuries. Watch out for sharp edges when you pick up the PCB. Visibly damaged parts can cause unpredictable danger. Do not use damaged parts: recycle and replace them with new ones. -
Page 5: Safe And Correct Soldering
WIB-33.2 English 3. Safe and correct soldering Caution: Incorrect soldering can cause dangers through fires and heat. Avoid these dangers by reading and following the directions given in the chapter Safety instructions. Use a small soldering iron with max. 30 Watt. Keep the soldering tip clean so the heat of the soldering iron is applied to the solder point effectively. -
Page 6: Operation Overview
4. Operation overview Possibilities of use The carriage lighting WIB-33.2 can be used in digital layouts driven in DCC or Motorola format as well as in analogue model railroad layouts. For the power supply digital boosters or analogue a.c. or d.c. - Page 7 English Operation in analogue mode The carriage lighting WIB-33.2 can also be used in analogue model railway layouts. When putting the vehicle on the rails the decoder recognizes automatically if it is run in analogue or digital mode and sets the corresponding operation mode.
- Page 8 English WIB-33.2 of 16 V or two goldcaps with a minimal voltage sustaining capability of 5,5 V. In order to supply the three function outputs of the decoder you can connect a second additional external bridging capacitor. It is not possible to use goldcaps here, as the minimal voltage sustaining capability is 25 V or 35 V (when connecting the PCB to analogue a.c.
-
Page 9: Technical Specifications
WIB-33.2 English 5. Technical specifications Data format DCC, Motorola Adress range MM: 1020 DCC: 2040 Hint: The adress range to be used also depends from the control unit. Speed levels (DCC- 14, 28 or 128 Format) Feedback log RailCom Supply voltage Digital voltage of the central unit or analogue d.c. -
Page 10: Mounting The Carriage Lighting
English WIB-33.2 6. Mounting the carriage lighting 6.1. Overall view P1 … power supply E(+) external bridging E(-) capacitor AUX1 decoder outputs AUX3 max. current: 300 mA AUX2 decoder output for therconnection of LEDs (back lighting) max. current: 20 mA... -
Page 11: Connection To The Power Supply
WIB-33.2 English 6.2. Connection to the power supply Solder the connecting wires for the power supply to the connecting points P1, P3 or P5 (from the left rail) and the connecting points P2, P4 or P6 (from the right rail). -
Page 12: Connecting Leds To The Output Aux2
English WIB-33.2 6.5. Connecting LEDs to the output AUX2 The output AUX2 has been designed for the connection of LEDs for the back lighting. The maximum current is 20 mA. The necessary series resistors are integrated on the PCB. Solder the LEDs to the connecting points AUX2 and RL2. -
Page 13: Setting The Leds´ Brightness
WIB-33.2 English 6.8. Setting the LEDs´ brightness Instead of programming with a digital control unit you can set the LEDs´ brightness via a trim-pot (see digram in section 6.1). For setting the trim-pot use a small screw-driver. The brightness programmed via CVs or register remains active, the settings at the trim-pot only alter the brightness with a factor valid for all LEDs. -
Page 14: Configuration Variables And Registers
English WIB-33.2 Programming with the Central Station and the Mobile Station With the Central Station or the Mobile Station of Märklin* you can program the registers, but the value to be set is limited to 80. Select the article no. 29750 from the locomotive database and program the decoder as described for this article in the Central Station´s or Mobile... - Page 15 WIB-33.2 English Auxiliary functions Name of CVs / Reg. Input value Remarks and Tips Registers (Default) Settings Reset 0 ... 255 Any input value restores the settings in state of delivery. Basic settings Name of CVs / Reg. Input value...
- Page 16 English WIB-33.2 Basic settings for the LEDs and the outputs Name of CVs / Reg. Input value Remarks and Tips Registers (Default) Settings Configuration 115 40 1 ... 255 (4) Fluorescent tube data 2 simulation off Fluorescent tube simulation on...
- Page 17 WIB-33.2 English Dependant on the direction of motion of the LEDs and the outputs Name of CVs / Reg. Input value Remarks and Tips Registers (Default) Settings LED1 | LED2 0, 1, 2, 16, LED 1, 3, 5 or 7 off...
- Page 18 English WIB-33.2 Settings for the orientation light Name of CVs / Reg. Input value Value in CV#115 Registers (Default) Function keys 118 41 1 ... 255 for activating orientation light It is possible to activate the function with several function keys.
-
Page 19: Presets
WIB-33.2 English 9. Presets Factory settings Preset 0 (default values) Applications / Control car Switching all functions Examples individually Switching the F1: each 2nd LED all LEDs individually LEDs F2: remaining LEDs with F1 to F8 Dim switch to be switched with F4... -
Page 20: Check List For Troubleshooting
English WIB-33.2 10. Check list for troubleshooting Parts are getting too hot and/or start to smoke. Disconnect the system from the mains immediately! Possible cause: one or more connections are soldered incorrectly. à Check the connections. Possible cause: Short circuit. The module is connected to locomotive or carriage ground. -
Page 21: Guarantee Bond
WIB-33.2 English 11. Guarantee bond For this product we issue voluntarily a guarantee of 2 years from the date of purchase by the first customer, but in maximum 3 years after the end of series production. The first customer is the consumer first... - Page 22 English WIB-33.2 Page 22...
- Page 23 WIB-33.2 English Page 23...
- Page 24 Actuele informatie en tips: http://www.tams-online.de Garantie und Service: Warranty and service: Garantie et service: Garantie en service: Tams Elektronik GmbH Fuhrberger Straße 4 DE-30625 Hannover fon: +49 (0)511 / 55 60 60 fax: +49 (0)511 / 55 61 61 e-mail: modellbahn@tams-online.de...