Front Basket Saddle Rear Cargo Bag Front Light Foldable Li-ion Battery Frame 24 x 4 Fat Tire Controller Front Hub Motor Rear Outer Derailleur 20*4.0 Fat Tire...
UNFOLDING THE PANDA ETRIKE 1. Use two people to prevent scratching the frame. 2. Have one person lift the trike from the bottom frame while another person unfolds it. 3. Fit the frame together and secure the clamp.
Page 5
HANDLE BAR INSTALLMENT Remove the nut on top and slide it up the stem of the handlebars. Take the two chrome pieces for the front basket and place them back-to-back. Insert the stem of the handlebars through them, ensuring they face the front. Slide the stem of the handlebars into the frame and use the provided tool to tighten the screw located straight up from the stem.
Page 6
FRONT WHEEL INSTALLMENT 1. Remove the nut and two washers from both sides of the wheel. 2. Identify the right side of the wheel (as you're sitting on the trike) by locating the side with the black cord. 3. Put the irregular washer on both sides of the wheel with the protruding side towards the wheel. Turn it until it seats into place. 4.
Page 7
FRONT WHEEL INSTALLMENT 1. Put the washer and the nut on both sides and tighten them with a large wrench. 2. Plug in the black cord to the connector found on the right fork. Ensure it is correctly connected and pushed all the way in.
Page 8
FRONT FENDER AND HEAD LIGHT INSTALLMENT 1. Use the existing bolt and nut to attach the front light and fender. Remove the nut using the correct Allen wrench and the smallest box wrench. 2. Remove the bolt, line up the light and fender, then replace the bolt and tighten the nut securely. 3.
Page 9
SADDLE INSTALLMENT 1. Insert the post into the saddle tube at the desired position. 2. Tighten the screw and secure the lever to keep the saddle in place. 3. Align the saddle with the frame to ensure it is straight. 4.
Page 10
CRANK ARM ISTALLMENT 1. Remove the crank arm bolt using an appropriate allen wrench. 2. Take the right crank arm and slide it securely onto the spindle. Tighten the bolt securely. 3. Carefully place the chain and thread it onto the right-side chaining of the crank arm.
Page 11
REAR FENDER & BASKET INSTALLMENT 1. Locate the packet labeled "rear basket" and remove the bolts and nuts. 2. Fit the back rack on the trike, ensuring the holes on the sides for the fenders align with the wheels. 3. Attach the fenders to the fender mount racks first. Bolt the fender racks to the back basket.
Page 12
REAR FENDER & BASKET INSTALLMENT 1. Leave the battery out to provide room for tightening the nuts and removing the insert. 2. Bolt the rack onto the trike and tighten the nuts under the rack.
Page 13
FRONT BASKET & PEDAL INSTALLMENT 1. Use four nuts and bolts from the labeled "front basket" bag to Identify the right and left pedals, ensuring the correct attach the basket to the trike. Use two additional nuts and bolts threading. Look for "R" or "L" markings; if not visible, make for the lid.
Page 14
BATTERY INSERTION & REMOVAL 1. The battery key has three positions. The first position is "On" and is all the way to the right. The second position is "Off" and is in the middle. The third position is the "Unlock" position, which is all the way to the left. Please note that you may need to push the key a little to turn it to the unlock position.Ensure that the key is fully turned and engaged in the unlock position.
Page 15
BATTERY CHARGING 1. Plug the charger into the battery first, then connect it to the wall plug. Remember to unplug it from the wall before disconnecting it from the battery. Charge for approximately 8-10 hours for the initial charge. 2. The battery can be charged either on or off the trike. When charging with the battery on the trike, turn the key to the off position.
DS103 DISPLAY USER MANUAL LCD Display Information "'. CD Headlight: display when the headlight is turned on; when the Time headlight is turned off or without this function, the icon will not be displayed; 07:07 Headlight 48.2V @ Speed: display the current speed value, KM/H: kilometers per hour, MPH: miles per hour;...
Page 17
DS103 DISPLAY USER MANUAL LCD Display Operation On/Off Keep the instrument and the controller in the normal connection state, press and hold △ seconds) when the instrument is off, the instrument will display the boot interface in full display, and then enter the basic interface normally and start ▽...
Page 18
DS103 DISPLAY USER MANUAL PAS level selection Press A or V to switch the power-assisted level, change the motor output power, the lowest 1 level, the highest 5 level, the default 1 level when the meter is turned on, and when it displays it is in neutral and no boost.
Page 19
DISPLAY SETTING DS103 DISPLAY USER MANUAL Speed and mileage display switch Press and hold V , after 2 seconds, the meter enters the walk- " , Short press cycling display: TRIP TIME/DISTANCE/ODO/ assisted push state, the PAS display area will display as" RANGE->...
Page 20
DISPLAY DS103 DISPLAY USER MANUAL SETTING Headlight switch Long press for 1 second, the headlights will be turned on, the meter display interface will switch to night mode, the headlight indicator icon will light up, and at the same time, long press again.
Page 21
DISPLAY DS103 DISPLAY USER MANUAL SETTING Power display When the battery power is normal, according to the battery capacity change, the battery power percentage is displayed in real time and 1-5 bars are disp layed. When the battery level is less than 5%, 0 bars will be displayed and the battery icon will flash. Prompt that it needs to be charged immediately.
Page 22
DISPLAY DS103 DISPLAY USER MANUAL SETTING Power display During riding, the meter displays the real-time power value and five-level indication of the power level, from low to high respectively, from level O to level 5, and level O means that the motor has no output assist.
Page 27
DS103 DISPLAY USER MANUAL Description Recommendatoin Description Recommendatoin Description Recommendatoin Battery under Charge the battery 12 V voltage drop Charge the battery Measured current Reduce the load on pack using the voltage (<27 V). detected ( < 11 V). pack using the oversteps the the motor by battery charger...
Page 28
DS103 DISPLAY USER MANUAL Description Recommendatoin Description Recommendatoin Description Recommendatoin Temperature Reduce the load on Cadence sens Switch off the sys 12 V out Switch off the sys short circuit tem completely. If overcurrent tem completely. If oversteps the the motor by the problem per...
FRONT SUSPENTION SETTING Please inflate the tire with the following instruction Front Suspention setting Step 2: Tilt the whole to the left until the tire is off the ground and adjust the safety line to fit the edge of the rim evenly.
PANDA ETRIKE DIAGNOSTIC Symptoms Most common solutions Possible causes ( l)lnsufficient battery power (l)Charge the battery It doesn't work (2)Faulty connections (2)Clean the connections (3)Key in wrong position (3)Turn the key into the correct position (l)lnsufficient battery power (l)Charge the battery Irregular acceleration and/or (2)Loose throttle magneto (2)Weld and adjust...
• Off-road riding requires close attention and specific skills and • Your bicycle comes with additional documents and manuals the present variable conditions and hazards which accompany the manufacturers of the system components. These documents must conditions. Wear appropriate safety gear and do not ride alone in also be read before using this product.
Page 36
NEED ASSISTANCE ? PLEASE CALL / TEXT 949-414-8003 or email info@perraroelectricbike.com Register your bike at www.perraroelectricbike.com Address : 2229 S Right St. Santa Ana CA 92705...