Advertisement
Quick Links
BEFORE YOU BEGIN
BEFORE YOU BEGIN
!
Please read these instructions carefully to
familiarize yourself with the required tools, materials,
and installation sequences. Follow the sections that
pertain to your particular installation. This will help
you avoid costly mistakes. In addition to proper
installation, read all operating and safety instructions
!
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
NOTES
!
Observe all local plumbing and plumbing codes.
!
Inspect waste and supply tubing; replace if
necessary.
!
The drain has removable parts.
!
Drain T is reversible for vertical or horizontal
" "
drainage.
!
Do not use sharp and hard objects when taking out
the drain plug to avoid scratching it.
Tools Required
!
Assorted screwdrivers
!
Adjustable or open end wrench
!
Pipe wrenches
!
Pliers
!
Manual hacksaw
!
Long flat nose pliers
FENG XIAN DISTRICT, SHANGHAI, CHINA
1260255-T01-D
SHANGHAI KOHLER LTD.,
!
!
!
!
!
!
T
!
!
!
!
!
!
!
NO.368, MIN LE ROAD,
POST CODE 201419
368
201419
©
Copyright Kohler China Investment Co., Ltd. 2017
-1-
©
VOLUTE
INSTALLATION INSTRUCTIONS
FILLER DRAIN
K-18669T/K-20609T
2017
Advertisement
Related Manuals for Kohler VOLUTE K-18669T
Summary of Contents for Kohler VOLUTE K-18669T
- Page 1 All information is based on the latest product information available at the time of publication. Kohler China Ltd. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice.
-
Page 2: Installation Preparations
X+Y=718 For K-18669T/ K-18669T X+Y=778 For K-20609T/ K-20609T OD41.5 OD38 Fig.#1 Kohler reserves the right to change marked dimensions without prior notice. INSTALLATION PREPARATIONS INSTALLATION PREPARATIONS Un-Assemble the spout from the overflow base. Plastic Barcket Metal Barcket Spout Kit Clamp Kit Screw Fig.#2a... -
Page 3: Installation
Assemble the overflow pipe, drain body and drain pipe together. For vertical drainage installations: Assemble parts as shown. Align the parts with the drain base. Align and tighten the nuts. Fig.#4 For horizontal drainage installations: Assemble parts as shown. Align the parts with the drain base. Align and tighten the nus. - Page 4 Insert Screw Here Plastic Barcket Assemble the plastic/metal bracket back to the overflow base from the inside of bath tub as shown. Metal Barcket Lower Edge of Important: The arc edge of the plastic bracket Overflow Hole should not lower than the lower edge of overflow Screw Arc Edge of hole, otherwise the button could not function well.
- Page 5 Please align the snap-fit. After insert all the control wire, push the push-botton base in to the base until a "Click”. Fig.#14 Pull Out Pull the tail of control wire from the drain hole. Fig.#15 Remove the rubber cover from the wire as shown, then fasten the control wire with the trigger kit.
- Page 6 Seal Apply Silicon Glue Pipe on Floor Fig.#19 Fasten the hose to the water outlet of the faucet Option1 Fasten the hose to the water outlet of the Cold faucet 72681T-ZX-CP 72681T-ZX-CP Fig.#20 Option2 Fasten the hose to the water outlet of the faucet 72681T-ZY-CP 72681T-ZY-CP Cold...
-
Page 7: Maintenance
Attention: After install, push the button repeatedly, make sure the plug could open and close normally. Run water into the bath, check the drain connections for leaks. MAINTENANCE Pull off the plug, unscrew the trigger kit, pull the control wire out to clean the hair on the wire. The accessories should be washed with warm water and a soft cloth or sponge.