Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Sound Storm D1000.2
Summary of Contents for Sound Storm D1000.2
- Page 1 ' s m a n u a l s e r i e s D400.2 D650.2 D1000.2 D350.4 D500.4...
-
Page 2: Table Of Contents
D - SERIES USER'S MANUAL Bridged Speaker Wiring With a Two Channel Amplifier Tri-Mode Speaker Wiring With a Two Channel Amplifier Bridged Speaker Wiring With a Four Channel Amplifier Dual Tri-Mode Speaker Wiring With a Four Channel Amplifier Specifications Features About Built-In Crossovers About Protection Circuitry Amplifier and 2 Ohm Operation... -
Page 3: Specifications
USA to the highest level of quality, and will afford you years of listening enjoyment. All D-SERIES amplifiers utilize regulated MOSFET power supplies, which assure that switching response is extremely fast and output power is clean. SOUND STORM Thank you for making MODEL RMS Watts / CH at 4 Ohms... -
Page 4: Features
Two Channel Amplifiers: D400.2, D650.2 and D1000.2 Amplifiers Two Channel Bridgeable Amplifier Tri-Mode Operation Heavy Duty Aluminum Alloy Heatsink Class A-B Operation Variable Low And High Pass Crossovers Variable Input Gain Control Variable Treble And Bass (0dB ~ +12dB) Line Output... -
Page 5: About Built-In Crossovers
Built-in Crossovers All D-SERIES amplifiers feature built-in electronic crossovers. The 2 Channel amplifiers(D400.2/D650.2/D1000.2) feature an adjustable low pass and high pass cross -overs and +12dB variable Bass Boost. The 4 Channel amplifiers(D350.4/D500.4) feature a pair of individually adjustable low pass crossovers and high pass crossovers, as well as and +12dB variable Bass Boost. -
Page 6: Electrical Wiring
Electrical Wiring All SOUND STORM LABORATORIES D-SERIES amplifiers are equipped with easy top access screw terminals. These terminals are Nickel Plated in order to ensure excellent electrical contact, and to resist corrosion. When making electrical connections to the amplifier, please observe the following: Use at least 8 gauge or heavier wires for power and ground connections. -
Page 7: Low Input And Line Output Wiring
If the HIGH LEVEL INPUTS are used, do not use the LOW LEVEL RCA inputs at the same time. The 2-Channel amplifiers use ONE High Level input for both channels and the 4-Channel amplifier use TWO of these connectors-one for each pair of channels. Two Channel Amplifiers: D400.2, D650.2 and D1000.2 Amplifiers Remote To OUTPUT Subwoofer Level... -
Page 8: Two Channel Speaker Wiring
TWO Channel Speaker Wiring Two Channel Amplifiers: D400.2, D650.2 and D1000.2 Amplifiers GROUND To REMOTE OUTPUT from HEAD UNIT To BATTERY Bridged Speaker Wiring Two Channel Amplifiers: D400.2, D650.2 and D1000.2 Amplifiers GROUND To REMOTE OUTPUT from HEAD UNIT To BATTERY... -
Page 9: Tri-Mode Speaker Wiring With A Two Channel Amplifier
Crossover (Subwoofer) as shown in the figure below. Please review the table below for inductor and capacitor component values to determine the desired crossover frequencies. Two Channel Amplifiers: D400.2, D650.2 and D1000.2 Amplifiers LOW PASS FILTER INDUCTOR HIGH PASS FILTER CAPACITORS... -
Page 10: Four Channel Speaker Wiring
Four Channel Speaker Wiring Four Channel Amplifiers: D350.4 and D500.4 Amplifiers GROUND To REMOTE OUTPUT from HEAD UNIT To BATTERY SPEAKER Bridged Speaker Wiring Four Channel Amplifiers: D350.4 and D500.4 Amplifiers GROUND To REMOTE OUTPUT from HEAD UNIT To BATTERY SPEAKER SPEAKER SUBWOOFER... -
Page 11: Dual Tri-Mode Speaker Wiring With A Four Channel Amplifier
Dual Tri-Mode Speaker Wiring Tri-Mode Operational Output is a unique feature which allows a Crossover (Subwoofer) to Be operated in MONO mode, while the main speakers are playing in STEREO. To engage the amplifier in this mode, place the Crossover (Subwoofer) switch in the "OUT" position. Use a 100v non-polar capacitor for a high pass crossover and a wire coil inductor to block high frequencies from the Crossover (Subwoofer) as shown in the figure below.Please review the table below for inductor and capacitor component values to determine the desired crossover frequencies. -
Page 12: Precautions
Precautions Before you drill or cut any holes, investigate your car's layout very carefully. Take care when you work near the gas tank, fuel lines, hydraulic line and electrical wiring. Do not operate the amplifier when it is un mounted. Attach all audio system components securely within the automobile to prevent damage, especially in an accident. -
Page 13: Troubleshooting
Troubleshooting Before removing your amplifier, refer to the list below and follow the suggested procedures, Always test the speakers and their wires first. No Output Confirm that all terminal strip connections are secure and tight. Check both in-line and built-in fuses. Both the "+12v" and the "REMOTE" terminals must have +12v referenced to chassis ground. - Page 14 MADE IN KOREA...