Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Excel 11790
Summary of Contents for Excel 11790
- Page 1 MODEL:11790...
-
Page 2: Scope Of Delivery
carefully follow its information. The machine can only 1. Introduction operated persons were instructed concerning Dear Customer, the operation of the machine and who are informed We hope your new tool brings you much enjoyment and about the associated dangers. The minimum age success. - Page 3 • Switch the chainsaw off before releasing the chain • If the chainsaw is not being used for a while, it must brake. be set aside in such a way that no other person is • To prevent injury, wear tight-fitting clothes and safety endangered.
-
Page 4: Transporting The Chainsaw
• Always set the claw stop before cross-cutting. Only • The chainsaw should not be used for forest work, i.e. then switch on the chainsaw and start sawing into the for felling and lopping off branches in the forest. wood. Pull the chainsaw upwards at the rear and lead Because of the cable connection the saw operator the direction with the front grip. -
Page 5: Intended Use
5. Intended Use 7. Technical Data The power tool is intended for sawing wood such as Specifications: wooden beams, planks, branches, tree trunks, etc., Voltage - 230-240V / 50Hz and for sawing of trees. Cuts can be sawed with or Power - 2400W across the grain. - Page 9 When warm, the saw chain will expand and slacken 9. Assembly and there is a danger of it jumping off the rail altogether. Re-tension if necessary. If the saw chain is Assembling the guide bar and saw chain(Fig1,2,3) The chainsaw must be unplugged. re-tensioned when hot, it must be loosened again when Important:The front finger guard (3) must always the sawing work has been completed.
- Page 10 Checking the automatic lubrication Releasing the chain brake (Fig 5) Before commencing work, check the automatic chain To be able to use your chain saw again, you must lubrication and oil gauge. Switch on the chain saw and release the saw chain again. First switch off the hold it above the ground.
- Page 11 After working with the chainsaw, you should Tips on chain saw use always: Clean the saw chain and guide bar and replace Sawing up wood (Fig 7a, 7b) the chain guard. To saw up wood, please observe the safety regulations and proceed as follows: Make sure the wood to be Chainsaw protection sawed cannot slip.
-
Page 12: Maintenance And Cleaning
Remember: To switch off: Pull the plug out of the power socket. Danger zone: Falling trees can bring down other trees To fell the tree, you must drive a wedge into the back with them. The danger zone is therefore twice the length cut. -
Page 13: Troubleshooting
12.Trouble Shooting The following table shows the types of breakdowns and indicates how you can correct it if your machine does not function correctly. If in spite of this, you do not manage to locate the problem and solve it, contact your after-sales service. -
Page 14: Parts Diagram And Parts List
Parts Diagram and Parts List... - Page 15 Parts Diagram and Parts List Description Description Front Handle Right Housing Label 2 Carbon Brush Insert Front Finger Guard Field Insert Washer1 Inner Connecting Wire4 Left Housing Capacitor Swicth Trigger Inner Connecting Wire2 Brake Block Inner Connecting Wire1 Screw Inner Connecting Wire3 Rivet Spring Adjust Board...
- Page 16 Parts Diagram and Parts List Description Description Output Bearing Oil Tank Bearing O Type Ring Cover Board Rubber Sheath On Oil Tank Screw Oil Tank Cap Rubber Ring Micro switch Sheath On Oil Tank Screw Ring Rubber Cork Spring Brake Belt Filter Screen Stopper Spring Washer Shaft Sleeve...
Need help?
Do you have a question about the 11790 and is the answer not in the manual?
Questions and answers
Hoy do i adjunto the Chano tension
To adjust the chain tension on the Excel 11790:
1. Locate the adjust board (part 10) and the saw chain (part 11) on the tool.
2. Loosen the screws or fasteners securing the guide bar (part 12).
3. Use the adjust board to either tighten or loosen the chain tension.
4. Once the desired tension is set, re-tighten the screws to secure the guide bar.
Ensure the chain is not too tight or too loose to avoid it jumping off or overheating.
This answer is automatically generated