Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Fieldmann Manuals
  4. Planer
  5. FDH 200801-E
  6. Manual

Fieldmann FDH 200801-E Manual

Hide thumbs Also See for FDH 200801-E:

Advertisement

Quick Links

Download this manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the FDH 200801-E and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Fieldmann FDH 200801-E

Summary of Contents for Fieldmann FDH 200801-E

  • Page 6: Table Of Contents

    Contents Electric Hand-held Planer INSTRUCTION MANUAL Thank you for your purchase of the electric hand-held planer. For your personal safety, read and understand the Instruction Manual before using. Keep the Instruction Manual in a safe place for future reference. CONTENTS 1.

  • Page 7: General Safety Instructions

    General safety instructions GENERAL SAFETY INSTRUCTIONS WARNING! Carefully read the instruction manual before use. Important safety warnings Unpack the product carefully and be sure not to throw away any part of the package before having found all components of the product. Keep the product in a dry place out of reach of children.
  • Page 8 General safety instructions Carefully read, remember and keep these safety instructions WARNING! In the use of electric machines and power tools, it is necessary to respect and follow the following safety instructions for the reasons of protection against electric shock, personal injury and danger of fire. The term “power tool” in the instructions below refers both to mains-operated (corded) power tool or battery-operated (cordless) power tool.
  • Page 9 General safety instructions If an extension cord is used, always check whether its technical parameters match the information specified in the type label of the power tool. When operating a power tool outdoors, use an extension cord suitable for outdoor use. If extension drums are used, these must be rolled out to prevent overheating of the cord.
  • Page 10 General safety instructions Power Tool Use and Maintenance Always disconnect the power tool from the mains in case of any problem during the work, before cleaning the power tool or its maintenance, during each transportation and after the completion of the work! Never operate a power tool if it is damaged in any way. Immediately stop working if the power tool generates abnormal noise or smell.

  • Page 11: Symbols

    Symbols SYMBOLS The product complies with the applicable standards and regulations. Read the Instruction Manual attentively prior to use. Double-insulated. Use eyes protective equipment Use ears protectiove equipment Wear a breathing mask. Subjected to recycling FDH 200 1-E...

  • Page 12: Proper Use

    Layout | Propeer Use | Before starting the equipment (Figs. 1/2/3) 1. Setting knob for the chip depth 2. Dust bag 3. Safety lock-off 4. ON/OFF switch 5. Rear base plate 6. Belt cover 7. Chip ejector 8. Front base plate 10.

  • Page 13: Operation

    Before starting the equipmen | Operation Turn the setting knob for the chip depth (1) in a counter-clockwise direction to set a lower chip depth: Lower chip depth After finishing work, set the chip depth so that the knives are lowered and thus protected from damage. Turn the setting knob for the chip depth to position “0”...
  • Page 14 Operation 6.2.2 Chamfering edges (Fig. 9-10) There is a V-shaped groove (a) in the front base plate that enables you to planer edges at an angle of 45° for a smooth finish. Switch on the tool and wait until it reaches full speed. Place the V-shaped groove (a) on the edge of the workpiece at an angle of 45°.

  • Page 15: Cleaning, Maintenance And Ordering Of Spare Parts

    Cleaning, maintanance and ordering of spare parts CLEANING, MAINTENANCE AND ORDERING OF SPARE PARTS Always pull out the mains power plug before starting any cleaning work. Cleaning Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipent with a clean cloth or blow it with compressed air at low pressure.
  • Page 16 Cleaning, maintanance and ordering of spare parts 1. Correct adjustment Result: Smooth planed surfaces 2. Notches in the surface Problem: The cutting edge on the planing knife (or both planing knives) is not parallel to the height ofthe rear base plate. 3.

  • Page 17: Technical Specifications

    Technical specifications TECHNICAL SPECIFICATIONS Electric hand-held planer: Mains voltage: 230V/50Hz Power input: Idling speed: Chip depth: 0-2mm Rebate depth: 0-6mm Planer width: 82mm Protection class: Weight: LpA sound pressure level dB(A) LWA sound power level dB(A) Vibration emission value ah = . Important ! The vibration value changes according to the area of application of the electric tool and may exceed the speci ied value in exceptional circumstances.
  • Page 18 Technical specifications ELECTRIC HAND-HELD PLANER OPERATING INSTRUCTIONS...

  • Page 19: Disposal

    Disposal INSTRUCTIONS AND INFORMATION ON DISPOSAL OF USED PACKAGING Put any used package material to the place determined by the municipality for waste disposal. DISPOSAL OF USED ELECTRIC AND ELECTRONIC EQUIPMEN This symbol on products or accompanying documents means that used electric or electronic products must not be put to ordinary municipal waste.