Download Print this page
Würth W-CBC.EC Manual
Würth W-CBC.EC Manual

Würth W-CBC.EC Manual

Portable edge bander

Advertisement

Quick Links

W-CBC.EC
Portable Edge Bander Manual
Attention: Read this manual before using your machine.

Advertisement

loading
Need help?

Need help?

Do you have a question about the W-CBC.EC and is the answer not in the manual?

Questions and answers

Summary of Contents for Würth W-CBC.EC

  • Page 1 W-CBC.EC Portable Edge Bander Manual Attention: Read this manual before using your machine.
  • Page 2: Grounding Instructions

    Max. Tape Width: 80 mm (3’’) or if in doubt as to whether the W-CBC.EC edge bander is Min. Workpiece Length: 120 mm (4 3/4’’) properly grounded. Use only 3-wire extension cords that have Feeder Speed: 5.5 m/min (18 ft/min)
  • Page 3 8 nuts (included), as shown below: 1. GLUE The glue to be used in your W-CBC.EC edge bander is a pellet type of glue. Before each use, check glue levels in the glue pot. The W-CBC.EC edge bander is tested to function with adequate glue levels.
  • Page 4 2. TAPE ADJUSTMENT OPERATIONS The W-CBC.EC edge bander is designed to work with PVC tape, ABS, paper and wood that do not have glue (only straight parts). The operations made by the W-CBC.EC edge bander, as well Use tapes approximately 4mm wider than the wood panel.
  • Page 5 To change the working temperature, press the LEFT ARROW key, making it possible to change parameters (press Note: You will notice that the W-CBC.EC edge bander can cut this button until you reach the desired temperature). Then the tape close to the wood panel, allowing better finished edges.
  • Page 6: Maintenance

    OFF and unplugged from the outlet to prevent or not even applying any glue on the wood. accidental discharges. If the glue axis of your W-CBC.EC edge bander is out of the GENERAL bracket, you can regulate it easily by following these steps: Periodic maintenance on your W-CBC.EC edge bander will...
  • Page 7 • Keep hands away from moving or sharp parts. • Check for damaged parts. Before continuing the use of the W-CBC.EC edge bander, a guard or other part that is • Turn off the machine and unplug the power cord before damaged should be examined carefully to determine its proper maintenance or adjustments of the tool.
  • Page 8: Warranty Terms

    The W-CBC.EC edge bander has engine 1-phase 110V. To avoid 9. The warranty does not cover problems caused by mistreatment, burning risk, check the voltage of your outlet before starting the carelessness, misuse or inappropriate use of the functions machine.
  • Page 9 SOLUTION GUIDE PROBLEM CAUSE SOLUTION Check the connection and the voltage of your Plug disconnected or connected improperly. power supply. Main switch off. Turn on the Main switch. Machine is not turn on ON switch off. Turn on the ON switch (green). Emergency switch activated.
  • Page 10 ELETRICAL DIAGRAMS & INFORMATION ENABLE HEAT AND CONTROL...
  • Page 11 ENABLE HEAT AND CONTROL POWER AND CONTROL HEATING/FEEDER...
  • Page 12 W-CBC.EC EDGE BANDER EXPLODED VIEW Description Qty. EDGEBANDER TABLE EDGEBANDER BODY...
  • Page 13 W-CBC.EC EDGE BANDER BODY EXPLODED VIEW Description Description TABLE BASE TAP BOLT M6X10 ZINC PLATED STEEL PITCH 1,0 CONTROL PANEL PLATE FOOT LEVEL 4013 M8X30 PANEL CONTROL BOARD HEX NUT M8 ZINC PLATED STEEL PITCH 1,25 POTENTIOMETER TAP BOLT M6X20 ZINC PLATED STEEL PITCH 1,0...
  • Page 14 W-CBC.EC EDGE BANDER TABLE EXPLODED VIEW Description Description EDGEBANDER TABLE TAP BOLT M5X25 ZINC PLATED STEEL PITCH 0,8 FLAT WASHER M6 ZINC PLATED STEEL ELASTIC SHAFT 3MMX25MM FLAT WASHER 1/4 ZINC PLATED STEEL DRIVING ROLL TAP BOLT M6X10 ZINC PLATED PITCH 1,0...
  • Page 15 NOTES:...
  • Page 16 Wurth Baer Supply Wurth Wood Group Wurth Louis & Co mpany McFadden’s 909 Forest Edge Dri v e 4250 Golf Acr e s Dri v e 895 Columbia Str e et 1-2323 Winston Park Dri v e Vernon Hills, IL 60061 Charlotte, NC 28208 Brea, CA 92821 Oakville, ON Canada L6H 6R 7...