PCB Piezotronics ICP M102B06 Installation And Operating Manual page 9

Model Number
102B06
Performance
Measurement Range(for ±5V output)
Useful Overrange(for ± 10V output)
Sensitivity(± 10 %)
Maximum Pressure(static)
Resolution
Resonant Frequency
Rise Time(Reflected)
Low Frequency Response(- 5 %)
Non-Linearity
Environmental
Acceleration Sensitivity
Temperature Range(Operating)
Temperature Coefficient of Sensitivity
Maximum Flash Temperature
Maximum Shock
Electrical
Output Polarity(Positive Pressure)
Discharge Time Constant(at room temp)
Excitation Voltage
Constant Current Excitation
Output Impedance
Output Bias Voltage
Electrical Isolation
Physical
Sensing Geometry
Sensing Element
Housing Material
Diaphragm
Sealing
Electrical Connector 10-32 Coaxial Jack
Weight
[4]
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
®
ICP is a registered trademark of PCB Piezotronics, Inc.
ICP® PRESSURE SENSOR
EN GLISH SI
500 psi 3,450 kPa
1,000 psi 6,895 kPa
10 mV/psi 1.45 mV/kPa
10,000 psi 68,950 kPa
2 mpsi 0.014 kPa
≥ 500 kHz ≥ 500 kHz
≤ 1.0 µ sec ≤ 1.0 µ sec
0.01 Hz 0.01 Hz
≤ 1.0 % FS ≤ 1.0 % FS
≤ 0.002 psi/g ≤ 0.0014 kPa/(m/s²)
-100 to +275 °F -73 to +135 °C
≤ 0.03 %/°F ≤ 0.054 %/°C
3,000 °F 1,650 °C
20,000 g pk 196,000 m/s² pk
Positive Positive
≥ 50 sec ≥ 50 sec
20 to 30 VDC 20 to 30 VDC
2 to 20 mA 2 to 20 mA
< 100 Ohm < 100 Ohm
8 to 14 VDC 8 to 14 VDC
8 8
10 Ohm 10 Ohm
Compression Compression
Quartz Quartz
Stainless Steel Stainless Steel
Invar Invar
Welded Hermetic Welded Hermetic
10-32 Coaxial Jack
0.41 oz 11.6 gm
Optional versions have identical specifications and accessories as listed for the standard model except
where noted below. More than one option may be used.
[1]
- Ablative Coating
CA
M - Metric Mount
[2]
Supplied Accessory: Model 065A40 Seal ring 0.435" OD x 0.397" ID x 0.030" thk brass (3) replaces
Model 065A03
N - Negative Output Polarity
[3]
- Stainless Steel Diaphragm
S
Diaphragm
- Water Resistant Cable
W
[2]
N OTES:
[1]For +10 volt output, minimum 24 VDC supply voltage required. Negative 10 volt output may be
limited by output bias.
[2]Typical.
[3]Zero-based, least-squares, straight line method.
[4]See PCB Declaration of Conformance PS023 for details.
SUPPLIED ACCESSORIES:
Model 065A03 Seal ring 0.435" OD x 0.377" ID x 0.030" thk brass (3)
Entered: ND Engineer: RPF
Date: 11/30/2022 Date: 11/30/2022 Date: 11/30/2022 Date: 11/30/2022 40734
3425 Walden Avenue, Depew, NY 14043
Revision: D
ECN #: 53357
OPTION AL VERSION S
316L Stainless Steel 316L Stainless Steel
Sales: RWM Approved: RPF Spec Number:
Phone: 716-684-0001
Fax: 716-684-0987
E-Mail: info@pcb.com