Advertisement
System Overview
Front View
585
Left Side View
Right Side View
Quick Setup
Installing VESA Mount (optional)
VESA Mount Accessories (optional)
VESA Mount (optional)
VESA Mount Screw
x 1
M6x15mm screw
(Round Head with
VESA Mount Kit
spring washer screw)
Installing Hooks (optional)
Step 1. Install the mounting brackets into the mounting holes on
the four sides of SP-S214 using 12 screws (M3x5mm).
Hook Accessories (optional)
x 12
M3x5mm screw
x 12
x 12
Mounting Bracket
M4x35mm screw
The following messages are reminders for safety on how to protect your panel PC from damages and extend the life cycle of SP-S214.
1. Check the Cable Voltage
•
The range of operating voltage should be AC input ATX 250W. Otherwise, the panel PC could be damaged.
2. Environmental Conditions
• Place your SP-S214 on a sturdy, level surface. Be sure to allow enough space to have easy access around the device.
• Avoid extremely hot or cold place to install SP-S214.
• Avoid exposure to sunlight for a long period of time or in an airtight space.
• Avoid the device from any heating device or using SP-S214 when it's been left outdoors in a cold winter day.
• Avoid moving SP-S214 rapidly from a hot place to a cold place and vice versa because condensation may come from inside of the device.
• Don't place SP-S214 close to any radio-active device in case of signal interference.
3. Handling
• Avoid putting heavy objects on top of the device.
• If water or other liquid spills into this product, unplug the power cord immediately.
Rear View
Top View
107.15
44.6
14.8
Bottom View
HDD Easy Maintenance
Step 2. P
ull out the HDD / SSD tray.
HDD Accessories
HDD Tray Screw
x 4
x 4
M4x10mm screw
M3x4.8mm Screw x 8
Step 2. Mount SP-S214 Panel PC equipped with 12 brackets
onto the wall firmly.
Step 3. Install 12 hooks onto the mounting brackets on the four sides
of Panel PC and fasten the mating screws to secure firmly.
x 12
M4 Nut
x 12
Hook
Safety Precaution
Rear I/O View
100(VESA)
55
75(VESA)
42.5
Wall Mount Cut-out Dimensions
527.80
360
Step 1.
Release the screw of the
HDD / SSD tray.
Wall
4. Good Care
• When the outside of the case is stained, remove the stain with a neutral washing agent with a dry cloth.
• Never use strong agents such as benzene and thinner to clean the device.
• If heavy stains are present, moisten a cloth with diluted neutral washing agent or with alcohol and then wipe thoroughly with a dry cloth.
• If dust has been accumulated on the outside, remove it by using a special vacuum cleaner for computers.
• The power cord with the plug shall be connected to a socket-outlet with earthing connections.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer's instructions.
WARNING! Some internal parts of SP-S214 may have high electrical voltage. And therefore we strongly recommend that qualified engineers can open and disassemble the device.
Please handle LCD and Touchscreen with extra care as they are easily breakable.
COM2
LAN1
Line In
COM3
LAN2
USB 2.0
COM1
USB3.0
Line Out
DVI-D
Mic In
549.2
532
368
184
Step 3.
Step 4. P
ush back HDD / SSD tray.
Installing Wall Oring (optional)
Step 1. Place the Wall O-ring into
the back of the front bezel.
Wall O-ring
Step 2. Fasten the 20 screws.
Wall
Wall Oring Accessories (optional)
M3x 28mm screw x 20
All Rights Reserved. Copyright 2017
(Unit: mm)
Remote
Switch
COM4
LPT Power
Button
Place the HDD / SSD and
fasten the four screws.
Step 5.
Fasten the screw of
the HDD / SSD tray.
Washer x 20
Advertisement
