Advertisement
System Overview
Front View
448 (SP-6267)
471 (SP-6269)
Right Side View
SP-6267
SP-6269
130.9
128.6
44.3
42
10
10
Quick Setup
Installing Panel Mount
Tighten the screws into the 12 mounting holes
(SP-6267) / 18 mounting holes (SP-6269) of the wall
fixture as shown to mount Panel PC onto the wall
securely. The panel mount installation is applicable for
both SP-6267 and SP-6269 Panel PCs.
Installing Hooks
SP-6267 & SP-6269
Step 1. Install the hooks into the mounting hole
on the four sides of SP-6267 & SP-6269
using 8 pieces M3x5mm screws.
The following messages are reminders for safety on how to protect your system from damages and to extend a long life of the system.
1. Check the Cable Voltage
•
The range of operating voltage should be be within the range of 100V to 240V AC. Otherwise, the system may be damaged.
2. Environmental Conditions
• Place your SP-6267 / SP-6269 on a sturdy, level surface. Be sure to allow enough space to have easy access around the system.
• Avoid extremely hot or cold place to install the system.
• Avoid exposure to sunlight for a long period of time or in an airtight space.
• Avoid the system from any heating device or using SP-6267 / SP-6269 when it's been left outdoors in a cold winter day.
• Bear in mind that the operating ambient temperature is from 0°C ~ 35°C for HDD & 0°C ~ 45°C for SSD.
• Avoid moving the system rapidly from a hot place to a cold place and vice versa because
condensation may come from inside of the system.
• Placing SP-6267 / SP-6269 in strong vigrations may cause hard disk failure.
• Don't place the system close to any radio-active device in case of signal interference.
Rear View (SP-6267)
C.L.100(VESA)
Top View
SP-6267
404
260
CFast
Reset
SIM Card
ANT
ANT
ANT
Bottom I/O View
Remote
DC IN
DVI-I
Switch
Power
Button
DIO
Installing 1st Memory and CPU
DRAM
Installing 2nd Memory and SSD
SSD cable *2
Wall
SP-6267 & SP-6269
Step 2. Mount SP-6267 & SP-6269 Panel
PC equipped with 8 hooks onto
the wall firmly.
Safety Precaution
Rear View (SP-6269)
C.L.100(VESA)
SP-6269
435
260
CFast
Reset
ANT
ANT
COM3
COM1
LAN
USB 3.0 MIC-in
1
Line Out
COM4
COM2
2
Line In
1
POE ON
2
I2C
M3 Screw*6
HEATSINK TOP COVER
CPU
M3 screw *6
Bottom Cover
SSD *2
M3 screw *4
SSD Bracket
SSD screw *8
DRAM
SP-6267 & SP-6269
Step 3. The operation is the same as above.
Wall
3. Handling
• Avoid putting heavy objects on top of the system.
• Don not turn the system upside down. This may cuase the floppy drive and hard drive to mal-function.
• If water or other liquid spills into this product, unplug the power cord immediately.
4. Good Care
• When the outside of the case is stained, remove the stain with a neutral washing agent with a dry cloth.
• Never use strong agents such as benzene and thinner to clean the system.
• If heavy stains are present, moisten a cloth with diluted neutral washing agent or with alcohol and then wipe thoroughly with a dry cloth.
• If dust has been accumulated on the outside, remove it by using a special made vacuum cleaner for computers.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer's instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And therefore we strongly recommend that qualified engineers
can open and disassemble the system. Please handle LCD and Touchscreen with extra care as they are easily breakable.
Wall Mount Cut-out Dimensions
SP-6267
SP-6269
SIM Card
ANT
Remote
DVI-I
COM3
COM1
Switch
Power
Button
DIO
COM4
COM2
DC IN 9~36V
POE ON
Installing VESA Mount
Hook Accessories (option)
Mounting Brackets
M3x5mm screw
x 4 for SP-6267 & SP-6269
M4x35mm screw
1. Install the bracket.
2. Tighten the screw.
(Unit: mm)
421.5
410
138
Wall
449
439
276
92
Wall
LAN
USB 3.0
MIC-in
1
Line Out
2
Line In
1
2
I2C
x 8 for SP-6267
x 8 for SP-6267
Hook
x 8 for SP-6267
x 8 for SP-6267
M4 Nut
All Rights Reserved. Copyright 2017
Advertisement
