Page 1
REFILLABLE CARBON FILTER PREMIUM AUSTRALIAN CHARCOAL USER MANUAL...
Page 3
WELCOME Thank you for choosing AC Infinity. We are committed to product quality and friendly customer service. If you have any questions or suggestions, please don’t hesitate to contact us. Visit www. acinfinity.com and click contact for our contact information.
PRODUCT WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Check your local code restrictions for additional safety measures that may be needed for a proper code compliant installation. Check local authority requirements for proper disposal of waste and residues. Read all instructions before installing and using this product.
KEY FEATURES REFILLABLE DESIGN RUST-RESISTANT ACTIVATED CARBON Easy-to-remove flanges Features powder-coated RC412 1200+ IAV Australian with rubber stopper ensure mesh that resists corrosion charcoal with high adsorption convenient disposal and and can withstand high rate to completely block odor refilling of activated carbon. humidity settings.
INSTALLATION STEP 1 Connect your duct tube over your filter. Use duct clamps to secure the connection. You may also apply ducting tape before using the duct clamps for further security. STEP 2 You may also connect your filter directly to your inline duct fan.
OVERHEAD HANGING STRAPS STEP 1 Loop the strap around a hanging pole. STEP 2 Slip the strap through the inner ladder lock slot from the bottom.
Page 11
OVERHEAD HANGING STRAPS STEP 3 Route the strap into the outer ladder lock slot from the top. Adjust the length of the completed loop as needed. STEP 4 Tuck the loose ends through the center gap of the ladder lock to secure the loop.
Page 12
OVERHEAD HANGING STRAPS STEP 5 Connect your filter to your ductwork using your preferred method, as shown on page 9.
Page 13
OVERHEAD HANGING ROPE CLIPS STEP 1 Loop the rope clip hangers around your grow tent's support beams. STEP 2 Hook the carabiners into the steel hooks located on the flanges.
CONFIGURATION SETUP PREFILTER When placing your filter inside your grow space, slip the cloth over your filter to block dust and other particles from passing through. Make sure the entire metal mesh is covered by the cloth. INTERIOR HANGING To use your filter in intake applications, place it inside your grow space.
Page 15
CONFIGURATION SETUP EXTERIOR MOUNTING To use your filter in exhaust applications, place the filter outside of your grow space. Make sure your filter is connected to your inline duct fan's exhaust end before completing the installation. Stuff the prefilter inside of the filter to lengthen the carbon bed's lifespan.
Page 16
CONFIGURATION SETUP OVERSIZED GROW SPACE Use a dual fan and filter combination inside your grow space to completely scrub away odor in larger grow rooms and tents. Set a second filter on the floor and an inline fan on top of it so that the exhaust end points up.
MAINTENANCE REVERSING THE FLANGES To extend your filter's lifespan and utilize its entire carbon bed, remove the flanges from either end, swap them to the other ends, and twist them back into place. Lay the filter horizontally when reversing the flanges.
REPLACING THE CARBON STEP 1 Rotate the port flange from your filter, then remove the rubber stopper from the interior. STEP 2 Dispose of the used carbon. Used carbon can be composted.
Page 19
REPLACING THE CARBON STEP 3 Place and direct the funnel into one of the openings and scoop the carbon refill into your filter. Make sure to evenly distribute and firmly pack the activated carbon as you refill your filter. Do not fill past the plastic barrier. STEP 4 Set the rubber stopper into place, making sure to align the nodes with the corresponding holes.
Page 20
REPLACING THE CARBON STEP 5 Twist the flange back onto your filter.
FREQUENTLY ASKED QUESTIONS How long will the activated carbon last? The included carbon should last between 1-2 grow cycles. This will depend on several factors including fan speed and frequency of use. What is the black dust coming from the activated carbon? Black dust from the carbon may appear due to movement during shipping, but should disappear after first use.
150 lb. weight capacity. Includes a mounting plate to install your AC Infinity controller onto. Inline Fans The CLOUDLINE series is a line of duct fans designed to quietly ventilate AV rooms and closets, as well as various DIY air circulation and exhaust projects.
WARRANTY This warranty program is our commitment to you, the product sold by AC Infinity will be free from defects in manufacturing for a period of two years from the date of purchase. If a product is found to have a defect in material or workmanship, we will take the appropriate actions defined in this warranty to resolve any issues.
Page 25
No part of the materials including graphics or logos available in this booklet may be copied, photocopied, reproduced, translated or reduced to any electronic medium or machine readable form, in whole or in part, without specific permission from AC Infinity Inc.