Summary of Contents for Backyard Products 03-0031-G
Page 1
5’ Quick Connect Turbo Slide Part Numbers: 03-0031-G 03-0031-B 03-0031-Y 51-1114 REV D 4.27.2023...
Page 2
Please inspect and inventory all parts immediately upon accepting delivery. Use the in- ventory pages in the manual to make sure you have received all necessary parts. The quickest method to get any parts that are missing or damaged is to contact the seller. WARNING CONTINUOUS ADULT SUPERVISION REQUIRED! STRANGULATION HAZARD...
Safety Tips: Observing the following statements and warnings reduces the likelihood of serious or fatal injury. WARNING: On-site adult supervision is required for children of all ages. INSTRUCT CHILDREN: • DO NOT walk close to, in front of, or behind slide. •...
Page 4
PLAYGROUND SURFACING MATERIALS SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK https://www.cpsc.gov/s3fs-public/325.pdf Select Protective Surfacing One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment.
General Info to Review Before Installation • Depending on your experience, assembly of the slide can take as little as 1-1/2 hours up to 2 hours, after inventory of parts; therefore, we recommend you set aside at least 2 hours for assembly. •...
Page 6
Tube Slide Placement QC Turbo for Custom Applications Below is a picture of a generic tower showing placement of the tube slide on all three available sides. You may not overlap safety zones. The slide itself may not occupy the swing beam safety zone.
Page 7
Tube Slide Dimensions 2 " Entry Dimensions (Inside View) 30" 16 " 26" Slide Height (A) 32" Lowest Setting 87-1/2" 16 " Middle Setting 89-3/4" Highest Setting 91-3/4" 16 " 4" This tube slide features an adjustable Exit Assembly that has a Low, Middle and High feature.
Page 8
Custom Framing Dimensions If you purchased a playset that came with this slide then refer to your manual regarding the framing of your playset. This step is intended for those who are constructing a custom playset of their own design. While this may not cover the exact details of your design it may be used as a general guideline for the installation.
Page 9
Custom Framing Dimensions (Exit Setting - LOW) Custom playset builders this is the "inside view" of the slide as if the rider is about to go down the slide from the deck level. Note that the railing in the configuration is about 31" high. By playset safety rules this railing with vertical slats has to be 27"...
Page 10
Custom Framing Dimensions (Exit Setting - Middle) Custom playset builders this is the "inside view" of the slide as if the rider is about to go down the slide from the deck level. Note that the railing in the configuration is about 31" high. By playset safety rules this railing with vertical slats has to be 27"...
Page 11
Custom Framing Dimensions (Exit Setting - High) Custom playset builders this is the "inside view" of the slide as if the rider is about to go down the slide from the deck level. Note that the railing in the configuration is about 31" high. By playset safety rules this railing with vertical slats has to be 27"...
Page 12
11-2016 5' Quick Connect Slide Hardware Kit 4/27/2023 JH REV E 5/16-18 x 9/16" 5/16-18 x 1/2" 5/16-18 x 1-3/8" 5/16-18 x 3/4" Pan Head Bolt Pan Head Bolt Pan Head Bolt Pan Head Bolt Square Drive Square Drive Square Drive Square Drive QTY: 45 QTY: 50...
Page 15
PICTURE DESCRIPTION QTY. Slide Mount Bracket 11-5030 Exit Support Bracket 11-5031 Exit Support Base 2-4-1800-B Exit Support Side Post 2-4-078-SP Exit Support Center Post 2-4-089-CP 11-2016 Slide Hardware (NOT SHOWN - SEE PREVIOUS PAGES IN MANUAL FOR LISTS) 11-2017 Exit Support Hardware 51-1114 Slide Instruction...
Page 16
STEP 1: Entrance Assembly Fasten Entrance Section (Right Side) to Entrance Section (Left Side) with eight 5/16” x 1/2”L Pan Head bolts. Note all 1/2”L bolts will have a blue stripe on the threads. This is a locking compound so the bolts will not come loose. 5/16”...
STEP 2: Elbow Assembly Fasten Elbow Sections together with eight 5/16” x 1/2”L Pan Head bolts. Assemble 3 Elbows total in this step. 5/16” x 1/2”L Pan Head Bolt...
Page 18
STEP 3: Elbow/Slide Mount Bracket Assembly Fasten Elbow Sections together with six 5/16” x 1/2”L Pan Head bolts. Fasten Slide Mount Bracket to Elbow with two 5/16” x 3/4”L Pan Head Bolts. Note all 1/2”L and 3/4”L bolts will have a blue stripe on the threads. This is a locking com- pound so the bolts will not come loose.
Page 19
STEP 4: Exit Elbow Assembly Fasten Elbow Section and Exit Elbow Section together with eight 5/16” x 1/2”L Pan Head bolts. Assemble 1 Elbow in this step. 5/16” x 1/2”L Pan Head Bolt...
Page 20
STEP 5: Exit Section/Exit Support Bracket Fasten the tab on the bottom of the Exit Section to the Exit Support Bracket with two 5/16” x 9/16” L Pan Head bolts and two 5/16” lock nuts. 5/16” Lock Nut Exit Support Bracket 5/16”...
Page 21
STEP 6: Entrance to 1st Elbow Fasten the Entrance to the Elbow with six 5/16” x 9/16” L Pan Head bolts and six 5/16” lock nuts. Tip: hold the bolt with the wrench provided. Use a 5/8” wrench to tighten nut. Note: Align Arrows.
Page 22
STEP 7: 1st Clamp Ring Fasten three Clamp Ring sections together over the intersection with three 5/16” x 1-3/8” L Pan Head bolts. Partially thread each bolt into the next clamp ring. When all bolts are par- tially installed tighten all three bolts. Note all 1-3/8”L bolts will have a blue stripe on the threads.
Page 23
STEP 8: 1st Elbow to 2nd Elbow Fasten the Elbows together with six 5/16” x 9/16” L Pan Head bolts and six 5/16” lock nuts. Note: Align Arrows. ALIGN ARROWS 5/16” Lock Nut 5/16” x 9/16”L Pan Head Bolt...
Page 24
STEP 9: 2nd Clamp Ring Fasten three Clamp Ring sections together over the intersection with three 5/16” x 1-3/8” L Pan Head bolts. 5/16” x 1-3/8”L Pan Head Bolt...
Page 25
STEP 10: 2nd Elbow to 3rd Elbow Fasten the Elbows together with six 5/16” x 9/16” L Pan Head bolts and six 5/16” lock nuts. Note: Align Arrows. 5/16” Lock Nut 5/16” x 9/16”L Pan Head Bolt...
Page 26
STEP 11: 3rd Clamp Ring Fasten three Clamp Ring sections together over the intersection with three 5/16” x 1-3/8” L Pan Head bolts. Clamp Ring section 5/16” x 1-3/8”L Pan Head Bolt...
Page 27
STEP 12: 3rd Elbow to 4th Elbow/Bracket Fasten the Elbows together with six 5/16” x 9/16” L Pan Head bolts and six 5/16” lock nuts. Note: Align Arrows. Slide 5/16” Mount Lock Nut Bracket Elbow with 5/16” x 9/16”L Slide Mount Pan Head Bolt Bracket...
Page 28
STEP 13: 4th Clamp Ring Fasten three Clamp Ring sections together over the intersection with three 5/16” x 1-3/8” L Pan Head bolts. Clamp Ring section 5/16” x 1-3/8”L Pan Head Bolt...
Page 29
STEP 14: 4th Elbow/Bracket to Exit Elbow Fasten the Elbows together with six 5/16” x 9/16” L Pan Head bolts and six 5/16” lock nuts. Note: Align Arrows. Exit Elbow 5/16” x 9/16”L Pan Head Bolt 5/16” Lock Nut...
Page 30
STEP 15: 5th (FINAL) Clamp Ring Fasten three Clamp Ring sections together over the intersection with three 5/16” x 1-3/8” L Pan Head bolts. Clamp Ring section 5/16” x 1-3/8”L Pan Head Bolt...
Page 31
STEP 16A: Exit Assembly (Low setting) Fasten the Exit Section to the Exit Base with four 5/16” x 9/16” L Pan Head bolts and four 5/16” Lock Nuts. Only use this setting for a play set deck height that is 57-7/16” Exit Section Exit...
Page 32
STEP 16B: Exit Assembly (Middle setting) Fasten the Exit Section to the Exit Base with four 5/16” x 9/16” L Pan Head bolts and four 5/16” Lock Nuts. Only use this setting for a play set deck height that is 59-9/16” Exit Section Exit...
Page 33
STEP 16C: Exit Assembly (High setting) Fasten the Exit Section to the Exit Base with four 5/16” x 9/16” L Pan Head bolts and four 5/16” Lock Nuts. Only use this setting for a play set deck height that is 61-3/4” Exit Section Exit...
Page 34
STEP 17A: Exit Support Assembly (Low setting) 1. Note the position of the small holes in Exit Support Side Post prior to installing T-nut. 2. Hammer T-nut into Exit Support Side Post. 3. Loosely assemble Side Posts to Center Post with bolt and washers. 4.
Page 35
STEP 17B: Exit Support Assembly (Middle setting) 1. Note the position of the small holes in Exit Support Side Post prior to installing T-nut. 2. Hammer T-nut into Exit Support Side Post. 3. Loosely assemble Side Posts to Center Post with bolt and washers. 4.
Page 36
STEP 17C: Exit Support Assembly (High setting) 1. Note the position of the small holes in Exit Support Side Post prior to installing T-nut. 2. Hammer T-nut into Exit Support Side Post. 3. Loosely assemble Side Posts to Center Post with bolt and washers. 4.
Page 37
STEP 18A: Exit Section to Exit Assembly 1. Place the flange of the Exit Section into the channel of the Exit Assembly. 2. Fasten the parts together with three 5/16” x 9/16” L Pan Head bolts and three 5/16” lock nuts.
Page 38
STEP 18B: Exit Section to Exit Assembly (Continued) 3. Fasten the Exit Elbow Section with cutout area to the Exit Assembly with two 5/16” x 9/16” L Pan Head bolts and two 5/16” lock nuts. Use wrench on inside radius to pre-align holes with nut as shown in Detail A and Detail B below.
STEP 19: Filler Boards 1. Measure in between the Top Rail and the Bottom Panel Board. If you are using our Custom Framing Dimensions from earlier you should get 25-1/4”. If not then record your measure- ment. 2. Cut two 2 x 4 boards to the 25-1/4” or to your measurement and then drill six 1/8” holes into the board as shown below.
Page 40
STEP 20A: Slide to Playset (Low Setting) 1. Make a mark onto the Top Rail at the center of the opening at 87-1/2” from the ground. Have an assistant help you lift the slide. Place the Slide Mount Bracket on top of the Cross Brace that is 27-9/16 from the ground.
Page 41
STEP 20B: Slide to Playset (Middle Setting) 1. Make a mark onto the Top Rail at the center of the opening at 89-11/16” from the ground. Have an assistant help you lift the slide. Place the Slide Mount Bracket on top of the Cross Brace that is 29-3/4 from the ground.
Page 42
STEP 20C: Slide to Playset (High Setting) 1. Make a mark onto the Top Rail at the center of the opening at 91-7/8” from the ground. Have an assistant help you lift the slide. Place the Slide Mount Bracket on top of the Cross Brace that is 31-15/16”...
Page 43
STEP 21A: Exit Support to Exit Bracket (Low Setting) 1. Position the Exit Support against the Exit Bracket as shown. 2. Center the Exit Support on the Exit Bracket holes. 3. Drill two holes 1/8” diameter by 1-1/4” deep at each mark. 4.
Page 44
STEP 21B: Exit Support to Exit Bracket (Middle Setting) 1. Position the Exit Support against the Exit Bracket as shown. 2. Center the Exit Support on the Exit Bracket holes. 3. Drill two holes 1/8” diameter by 1-1/4” deep at each mark. 4.
Page 45
STEP 21C: Exit Support to Exit Bracket (High Setting) 1. Position the Exit Support against the Exit Bracket as shown. 2. Center the Exit Support on the Exit Bracket holes. 3. Drill two holes 1/8” diameter by 1-1/4” deep at each mark. 4.
Page 46
STEP 22: Small Gaps 1. Gaps greater than 1/4” on the sides,top or bottom can be closed by drilling a 1/4” hole through the plastic only. Example shown at top and on side below. 2. Install a 1/4” x 1-1/4” Wafer head lag screw at the hole. "...
Page 47
WARRANTY - 5’ Quick Connect Turbo Slide Backyard Playnation, LLC takes great pride in the quality and durability of our products. Our Manufacturer’s Limited Warranty provides confidence and demonstrates our commitment to providing quality residential playground products. If you have any questions, please call our Customer Service Department at: 770-704-9300 LIMITED LIFETIME WARRANTY...
Page 48
Backyard Playnation, LLC WILL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. This warranty is non-transferable and does not extend to the owners of the product subsequent to the original purchaser. Some states do not allow limitations on implied warranties or exclusion of incidental or consequential damages, so these restrictions may not be applicable to you.