Normal deterioration and wear of the exterior finishes, or product label replacement. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears Brands Management Corporation, Hoffman Estates, IL 60179 PRODUCT SPECIFICATIONS...
SAFETY INSTRUCTIONS WARNING DANGER This machine was built to be operated according to the safe opera- This symbol points out important safety instructions which, if not tion practices in this manual. As with any type of power equipment, followed, could endanger the personal safety and/or property of carelessness or error on the part of the operator can result in serious yourself and others.
Page 4
SAFETY INSTRUCTIONS SLOPE OPERATION • Slow down before turning. Operate the machine smoothly. Avoid erratic operation and excessive speed. Slopes are a major factor related to loss of control and tip-over • Disengage blade(s), set parking brake, stop engine and wait until accidents which can result in severe injury or death.
Page 5
SAFETY INSTRUCTIONS CHILDREN SERVICE Tragic accidents can occur if the operator is not alert to the presence Safe Handling of Gasoline of children. Children are often attracted to the machine and the mowing To avoid personal injury or property damage use extreme care in activity.
Page 6
(O.E.M.) parts only, listed in this manual. Use of parts which do not meet the original equipment specifications may A spark arrestor for the muffler is available through your nearest Sears lead to improper performance and compromise safety! Parts and Repair Service Center.
Page 7
SAFETY INSTRUCTIONS SAFETY SYMBOLS This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate DANGER—...
ASSEMBLY IMPORTANT: Your tractor is shipped with motor oil in the engine. However, Shipping Brace Removal you MUST check the oil level before operating. Refer to the Service & Maintenance WARNING section for instructions on checking the oil level. Make sure the riding mower’s engine is off, remove the ignition key, and NOTE: Any reference in this manual to the RIGHT or LEFT side of the set the parking brake before removing the shipping brace.
Page 10
ASSEMBLY Adjusting the Seat To adjust the position of the seat, pull up and hold the seat adjustment lever. Slide the seat forward or rearward to the desired position; then release the adjustment lever. Make sure seat is locked into position in a seat-stop before operating the tractor.
OPERATION Figure 6 Parking Brake Lever PTO Lever (Blade Engage) Throttle/Choke Control Lever Cup Holder Ignition Switch Module Shift Lever Auto-drive Pedal Seat Adjustment Lever Deck Lift Lever Brake Pedal NOTE: Any reference in this manual to the RIGHT or LEFT side of the tractor is observed from operator’s seat position facing forward towards the front of tractor.
Page 12
OPERATION Parking Brake Lever Seat Adjustment Lever To set the parking brake: Fully depress the brake pedal. Move the The seat adjustment lever is located below the front/left of the seat. The lever parking brake lever into the parking brake position. Release the allows for adjustment of the fore and aft position of the seat.
Page 13
OPERATION Gas and Oil Fill-up IMPORTANT: Your tractor is shipped with motor oil in the engine. However, you MUST check the oil level before operating. Be careful not to overfill. For instructions on how to check the engine oil, refer to Checking The Engine Oil in the Service and Maintenance section of this manual.
Page 14
OPERATION Setting the Cutting Height • The engine will automatically shut off if the PTO (Blade Engage) lever is moved into the engaged (ON) position with the shift lever in Reverse. Select the height position of the cutting deck by placing the deck lift lever in Ignition Switch any of the different cutting height notches on the right side of the fender.
Page 15
OPERATION Driving The Tractor CAUTION Do NOT hold the key in the START position for longer than ten seconds WARNING at a time. Doing so may cause damage to your engine’s electric Avoid sudden starts, excessive speed and sudden stops. starter.
Page 16
The lamps turn OFF when the ignition key is moved to the STOP position. A mulch kit can be purchased through the retail location in which you purchased this tractor. For more information, simply contact Sears at 1-800-659-5917. Using the Deck Lift Lever To raise the cutting deck, move the deck lift lever to the left, then place it in the notch best suited for your application.
SERVICE AND MAINTENANCE MAINTENANCE SCHEDULE WARNING Before performing any type of maintenance/service, disengage all controls Follow the maintenance schedule given below. This chart describes service and stop the engine. Wait until all moving parts have come to a complete guidelines only. Use the Service Log column to keep track of completed stop.
Page 18
SERVICE AND MAINTENANCE Engine Maintenance Changing Engine Oil The engine oil should be changed in the first 5 hours and then every 50 hours or Checking the Engine Oil once a season. To change the engine oil, proceed as follows: Only use high quality detergent oil rated with API service classification SF, SG, With engine OFF but still warm, disconnect spark plug wire and keep it away SH, or SJ.
Page 19
SERVICE AND MAINTENANCE Fuel Filter Air Cleaner WARNING The air filter system uses a cylindrical cartridge. Remove the fasteners (A) and the air filter cover (B). See Figure 13. Gasoline and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death.
Page 20
SERVICE AND MAINTENANCE Muffler IMPORTANT: If removing the battery for any reason, disconnect the NEGATIVE (Black) wire from its terminal first, followed by the POSITIVE (Red) wire. When WARNING re-installing the battery, always connect the POSITIVE (Red) wire to its terminal first, followed by the NEGATIVE (Black) wire.
Page 21
SERVICE AND MAINTENANCE Move the tractor’s PTO (Blade Engage) into the ON position. Measure the distance from the front of the blade tip to the ground and the rear of the blade tip to the ground. The first measurement taken should Remain in the operator’s position with the cutting deck engaged for a minimum of be between ¼”...
Page 22
Move the deck lift lever into the top notch on the right fender to raise the the brake is in need of adjustment. Contact the nearest Sears Service Center to have deck lift arms up and out of the way.
Page 23
SERVICE AND MAINTENANCE The recommended operating tire pressure is: Remove the bow-tie cotter pin securing the deck stabilizer rod to the deck. Slide the deck lift rod from the mounting bracket on the deck as shown in • Approximately 10 psi for the rear tires Figure 20.
Page 24
SERVICE AND MAINTENANCE If your tractor has not been put into use for an extended period of time, charge the To properly sharpen the cutting blades, remove equal amounts of metal battery as follows: from both ends of the blades along the cutting edges, parallel to the trailing Set your battery charger to deliver a max of 10 amperes.
Page 25
SERVICE AND MAINTENANCE Parking Brake Adjustment To change or replace the deck belt on your tractor, proceed as follows: Remove the deck as instructed earlier in this section. WARNING Remove the belt covers from the spindle pulleys by removing the hex screws Never attempt to adjust the brakes while the engine is running.
OFF-SEASON STORAGE WARNING Never store lawn tractor with fuel in tank indoors or in poorly ventilated areas where fuel fumes may reach an open flame, spark, or pilot light as on a furnace, water heater, clothes dryer, or gas appliance. Preparing The Engine Draining The Fuel IMPORTANT: Fuel left in the fuel tank during warm weather deteriorates and...
TROUBLESHOOTING Problem Cause Remedy Engine fails to start PTO/Blade Engage lever engaged. Place lever in disengaged (OFF) position. Parking brake not engaged. Engage parking brake. Spark plug wire(s) disconnected. Connect wire(s) to spark plug(s). Throttle/Choke control lever not in correct Place Throttle/Choke lever into the FAST position.
951-12179A Fuel Cap 951-12426 Fuel Cap (CA) 777D18559 Parts available at most Sears Retail Stores and Service Centers or call 1-800-366-PART(7278) if you want the part sent directly to your home. X46404 Specific tractor attachments for your Craftsman tractor available at Sears Stores and Service Centers.
Page 29
Notes Page This page intentionally left blank. Use this page to make any notes regarding your tractor.
Page 37
PARTS LIST Craftsman Model 247.288853 Ref. Part No. Description 710-04482 Hex Flange Bolt, 3/8-16 x .875 710-04484 Screw, Hd. Tapp, 5/16-18 x .75 712-3004A Flange Lock Nut, 5/16-18 925-05013 Seat Safety Switch 757-04145 Seat 926-0154 Push Mount Cable Tie 732-04035 Spring, Compress., 1.28 x 3.125 732-04563 Spring, Compress., .68 x 1.065 x .055...
Page 41
PARTS LIST Craftsman Model 247.288853 Ref. Part No. Description Ref. Part No. Description 736-3040 Flat Washer, .406 x 1.920 x .060 918-04566 Transmission Drive Assembly 17962 Plate Switch 936-0185 Flat Washer, .375 X .738 X .063 725-04363 Switch Interlock 647-04266 Shaft Lever Assembly 634-0104 Wheel, 20 x 8 x 8...
Page 43
PARTS LIST Craftsman Model 247.288853 Ref. Part Number Description Ref. Part Number Description 738-04278 Shoulder Screw, 1/4-20 x 0.50 918-04865A Spindle Assembly, Pul 6.93 Dia 736-0262 Washer, Flat, .385 x .870 x .092 683-0254B Bracket Assembly, Deck Hanger, LH 738-04091A Shoulder Spacer, .43 x .29, 5/16-18 631-04288 Chute Deflector Assembly...
Page 44
PARTS LIST Craftsman Engine Model 331877-0869-G5 For Model 247.288853 1330 REPAIR MANUAL 48 SHORT BLOCK 1058 OPERATOR’S MANUAL 1329 REPLACEMENT ENGINE 1264 1263 1270 1017 1027 1024...
Page 45
PARTS LIST Craftsman Engine Model 331877-0869-G5 For Model 247.288853 415A 186A 1022 1034 1029 1023 1022 1026...
Page 46
PARTS LIST Craftsman Engine Model 331877-0869-G5 For Model 247.288853 1091 1127 1266...
Page 47
PARTS LIST Craftsman Engine Model 331877-0869-G5 For Model 247.288853 1036 EMISSIONS LABEL 1040 1279 1265 305A 305B 187A 187B 1139 1005 1044 1051...
Page 48
PARTS LIST Craftsman Engine Model 331877-0869-G5 For Model 247.288853 1059 1119 1051 1090...
Page 49
PARTS LIST Craftsman Engine Model 331877-0869-G5 For Model 247.288853 121 CARBURETOR OVERHAUL KIT 1266 358 ENGINE GASKET SET 1022 1266 1095 VALVE GASKET SET 1022...
Page 50
PARTS LIST Craftsman Engine Model 331877-0869-G5 For Model 247.288853 Ref. Ref. Part No. Description Part No. Description 794128 Cylinder Assembly 695408 Kit-Idle Speed 399265 Bushing/Seal Kit (Magneto Side) 694918 Pin-Float Hinge 391086s Seal-Oil (Magneto Side) 696136 Valve-Float Needle 697188 Sump-Engine 695419 Valve-Choke 796026...
Page 51
PARTS LIST Craftsman Engine Model 331877-0869-G5 For Model 247.288853 Ref. Ref. Part No. Description Part No. Description 690323 Screw (Starter Motor) 697392 Pin-Counterweight 497608 Brush Set 796448 Retainer (Fuel Pump) 796309 Screen/Cup Assembly 693713 Gear-Pinion 795315 Armature-Magneto 698329 Harness-Wiring 691061 Screw (Magneto Armature) 693167 Nut (Brush Retainer)
Page 52
PARTS LIST Craftsman Engine Model 331877-0869-G5 For Model 247.288853 Ref. Part No. Description 1091 691333 Cap-Limiter 1095 794152 Gasket Set-Valve 1119 691183 Screw (Alternator) 1127 695407 Screw (Float Bowl) 1139 796449 Washer (Fuel Pump) 1263 697124 Reed-Breather 1264 697104 Screw (Breather Reed) 1265 794151 Support-Blower Housing...
Page 53
After July 1, 2000, Look For Emissions Compliance Period On Engine Emissions Compliance Label After July 1, 2000 certain Sears Brands Management Corporation engines will be certified to meet the United States Environmental Protection Agency (USEPA) Phase 2 emission standards. For Phase 2 certified engines, the Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements.
Page 54
Sears Emission Control Defects Warranty Provisions The following are specific provisions relative to your Emission Control Defects Warranty Coverage. It is in addition to the Sears engine warranty for non-regulated engines found in the Operating and Maintenance Instructions.
Page 55
FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS MTD Consumer Group Inc, the United States Environmental Protection Agency (EPA), and, for those products certified for sale in the state of California, the California Air Resources Board (CARB) are pleased to explain the emission (evaporative and/or exhaust) control system (ECS) warranty on your outdoor 2006 and later small off-road spark-ignited engine and equipment (outdoor equipment engine) In California, new outdoor equipment engines must be designed, built and equipped to meet the State’s stringent anti-smog standards (in other states, 1997 and later model year equipment must be designed, built, and equipped to meet the U.S.
Page 56
Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on or modified parts by the ultimate purchaser will be grounds for disallowing a warranty claims. MTD Consumer Group Inc will not be liable to warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.
Page 57
Discount of 25% from regular price of service and related installed parts not covered by the agreement; also, 25% off regular price of preventive maintenance check Fast help by phone – we call it Rapid Resolution – phone support from a Sears representative. Think of us as a “talking owner’s manual.”...
El deterioro normal y el desgaste de los acabados exteriores, o reemplazo de la etiqueta del producto. Esta garantía le otorga derechos legales específicos, y usted también puede tener otros derechos que varían de estado a estado. Sears Brands Management Corporation, Hoffman Estates, IL 60179 ESPECIFICACIONES DEL NÚMERO DE MODELO...
Page 59
INSTRUCCIONES DE SEGURIDAD ADVERTENCIA PELIGRO Esta máquina fue construida para ser operada de acuerdo con La presencia de este símbolo indica que se trata de instrucciones las reglas de seguridad contenidas en este manual. Al igual que importantes de seguridad que se deben respetar para evitar con cualquier tipo de equipo motorizado, un descuido o error por poner en peligro su seguridad personal y/o material y la de otras parte del operador puede producir lesiones graves.
Page 60
INSTRUCCIONES DE SEGURIDAD • Nunca deje la máquina en funcionamiento sin vigilancia. Apague • Vaya a baja velocidad. Elija una velocidad lo suficientemente baja, siempre las cuchillas, coloque el freno de mano, detenga el motor y de modo que no tenga que detenerse o hacer cambios mientras retire la llave antes de bajarse del vehículo.
Page 61
INSTRUCCIONES DE SEGURIDAD • Para evitar accidentes al operar en marcha atrás, siempre desengan- • Apague todos los cigarrillos, cigarros, pipas y otras fuentes de che las cuchillas antes de colocar marcha atrás. Si está instalado, combustión. el “Modo Precaución Marcha Atrás” (hojas de operar la máquina, •...
Page 62
útil media de siete (7) años, ó 270 horas de funcionamiento. Al finalizar la vida útil media, adquiera una máquina nueva o haga inspeccionar anualmente ésta Sears por uno u otro distribuidor de servicios para cerciorarse de que todos los sistemas mecánicos y de seguridad funcionan correctamente y no tienen excesivo desgaste.
Page 63
INSTRUCCIONES DE SEGURIDAD SÍMBOLOS DE SEGURIDAD Esta página representa y describe la seguridad los símbolos que pueden parecer en este producto. Lea, comprenda, y siga todas instrucciones en la máquina antes procurar para reunir y operar. Symbol Description LEA EL MANUAL(S) DEL OPERADOR leído, entienda, y siga todas las instrucciones en el manual(s) antes de procurar montar y funcionar PELIGRO—...
Page 65
ASAMBLEA ENVÍO BRACE ELIMINACIÓN IMPORTANTE: Su tractor se entrega con aceite de motor en el motor. Sin embargo, debe comprobar el nivel de aceite antes de ADVERTENCIA operar. Consulte la sección de Servicio y Mantenimiento para obtener Asegúrese de que el motor del tractor cortacésped es, retire la llave instrucciones sobre la comprobación del nivel de aceite.
Page 66
ASAMBLEA Coloque la arandela (con la parte ahuecada hacia abajo) sobre el Conecte el mazo de cables en el interruptor de seguridad del asiento volante y segura con el tornillo hexagonal. Véase la figura. 3. en la parte inferior del asiento, como se muestra en B de la Figura NOTA: El tractor no funciona con el cable de alimentación desconectado.
Page 67
OPERACIÓN Figure 6 Palanca del freno de estacionamiento Toma de fuerza de palanca (Blade Engage) Acelerador y palanca de control de Choke Portavasos Ignition Switch Module De Velocidad Auto-disco pedal Palanca de ajuste del asiento Levante la palanca de la cubierta Pedal de freno NOTA: Cualquier referencia hecha en este manual al lado DERECHO o IZQUIERDO del tractor debe entenderse tal como se observa desde la posición del operador.
Page 68
OPERACIÓN FRENO DE ESTACIONAMIENTO PALANCA DE AJUSTE DEL ASIENTO Para ajustar el freno de estacionamiento: completa- La palanca de ajuste del asiento se encuentra debajo de la parte mente el pedal de freno. Mover la palanca del freno de frontal / izquierda del asiento. La palanca permite el ajuste de la parte estacionamiento en la posición del freno de estaciona- delantera y la posición longitudinal del asiento.
Page 69
OPERACIÓN LA PALANCA DE CAMBIO se enfríe por lo menos dos minutos antes de volver a cargar combustible. La palanca de cambios está situada en • Limpie el combustible que se haya derramado sobre el motor y el el lado izquierdo de la defensa y tiene equipo.
Page 70
(ON) la posición. segura del tractor. Si este sistema nunca deja de funcionar correcta- Suelte el pedal del freno para que el freno de estacionamiento a mente, no opere el tractor, contacte inmediatamente con su Sears participar. Parts & Repair Service Center.
Page 71
OPERACIÓN PARO DEL MOTOR ADVERTENCIA Si se golpea un objeto extraño, detenga el motor, desconecte el cable de la bujía (s) y tierra contra el motor. Inspeccionar cuidadosa- mente el equipo de los daños. Reparación de los daños antes de reiniciar y de funcionamiento.
Page 72
OPERACIÓN CONDUCCIÓN EN LAS LADERAS INVOLUCRAR A LOS BLADES Participación de la toma de fuerza (Blade Engage) las transferencias de Refieren al ancho de la pendiente en la seguridad de las prácticas de energía a la plataforma de corte o de otro tipo (disponible por separado) operación importante sección del manual para ayudar a determinar los archivos adjuntos.
Page 73
OPERACIÓN CORTAR FAROS ADVERTENCIA • Las lámparas están ON cuando el motor del tractor se está ejecutando. Para ayudar a evitar el contacto con la cuchilla o una lesión en • Las luces se apaga cuando la llave de contacto se mueve a la el objeto lanzado, Mantenga a los espectadores, los ayudantes, posición STOP.
Page 74
SERVICIO Y MANTENIMIENTO LISTA DE MANTENIMIENTO ADVERTENCIA Antes de realizar cualquier tipo del mantenimiento/servicio, suelte Siga la lista de mantenimiento dada abajo. Esta carta describe pautas todos los mandos y pare el motor. Espere hasta que todas las partes de servicio sólo. Use la columna de Tronco de Servicio para guardar la de movimiento hayan venido a una parada completa.
Page 75
El aceite usado es un producto de residuos peligrosos. Deseche el aceite usado correctamente. No desechar con los residuos domésti- Full cos. Consulte con las autoridades locales o Sears Centro de Servicio para la eliminación segura / instalaciones de reciclaje. PRECAUCIÓN El aceite usado es un producto de residuos peligrosos.
Page 76
SERVICIO Y MANTENIMIENTO Fuel Filter Reemplace el filtro de combustible con un original filtro de reemplazo de equipo. Contacto Sear’s al 1-800-4-MY-HOME ® • Mantenga la gasolina lejos de chispas, llamas, luces piloto, el para comprar el original de filtro de reemplazo del equipo. calor, y otras fuentes de ignición.
Page 77
SERVICIO Y MANTENIMIENTO Bujía Puntos de pivote y Vinculación Limpie el área alrededor de la base de la bujía. No chorro de Lubricar todos los puntos de giro en el sistema de tracción, freno de arena de la bujía. La bujía debe limpiarse por raspado o cepillo estacionamiento y la vinculación levantar al menos una vez al año con de alambre y el lavado con un disolvente comercial de aceite de la luz.
Page 78
SERVICIO Y MANTENIMIENTO LIMPIEZA DEL TRACTOR corte enganchada durante dos minutos como mínimo, permi- tiendo que la parte inferior de la plataforma de corte se lave a Si se derrama combustible o aceite sobre la máquina, debe limpiarse fondo. de inmediato. NO permita que se acumulen desechos alrededor de las Mueva la potencia de arranque (enganche de cuchilla) del tractor aletas de refrigeración del motor, el ventilador de refrigeración de la a la posición OFF (apagado).
Page 79
Si la plataforma de corte parece ser la siega de forma desigual, un lado a lado de ajuste puede ser realizado. Ajuste si es necesario lo Para ubicar el Centro de Servicio más cercano Sears o para pro- gramar el servicio, simplemente póngase en contacto con Sears siguiente: al 1-800-4-MY-HOME ®.
Page 80
SERVICIO Y MANTENIMIENTO Retire la correa (C) de alrededor de la polea del motor del tractor. Retire con cuidado el cable de toma de fuerza de la parte trasera Véase la figura. 19. de la plataforma de corte al eliminar el clip de horquilla que lo sujeta.
Page 81
SERVICIO Y MANTENIMIENTO EL ARRANQUE CARGA ADVERTENCIA ADVERTENCIA Nunca salte iniciar una batería dañada o congelados. Esté seguro de Baterías emiten un gas explosivo durante la carga. Carga de la los vehículos no se tocan, y están fuera de ignición. No permita que batería en un área bien ventilada y mantenerse lejos de una llama las abrazaderas de cable al tacto.
Page 82
SERVICIO Y MANTENIMIENTO CUCHILLAS DE CORTE ADVERTENCIA Apague el motor y quite la llave de encendido antes de retirar la cuchilla de corte (s) para afilar o de sustitución. Proteja sus manos usando guantes gruesos al sujetar la hoja. ADVERTENCIA Inspeccione periódicamente la hoja y / o husillo de grietas o daños, sobre todo después de haber llegado a un objeto extraño.
Page 83
Comuníquese con el Centro de Servicio y alrededor de los guardias de la correa. Después de aflojar más cercano Sears que su correa de transmisión de transmisión de las poleas locas de la plataforma, gire la guía de la correa de la los servicios.
Page 84
ALMACENAMIENTO FUERA DE TEMPORADA ADVERTENCIA Nunca almacene tractor de césped con combustible en el tanque en un espacio cerrado o en áreas con poca ventilación, donde los gases del combustible puedan alcanzar el fuego, chispas o una luz piloto como la que tienen algunos hornos, calentadores de agua, secadores de ropa o algún otro dispositivo a gas.
Page 85
SOLUCIÓN DE PROBLEMAS Problema Causa Remedio El motor no arranca Perilla de potencia de arranque (PTO) Coloque la perilla en la posición de desconexión conectada. (OFF). No está colocado el freno de mano. Coloque el freno de mano. Se ha desconectado el cable de las bujías. Conecte el cable a las bujías.
Page 86
Página de notas Esta página se dejó intencionalmente en blanco. Utilice esta página para tomar notas acerca de su tractor.
Page 87
Los motores cuyo cumplimiento con los estándares de emisión Tier 2 de la Comisión de Recursos Ambientales de California (CARB) esté certificado deben exhibir la información relacionada con el período de duración de las emisiones y la clasificación de aire. Sears Brands Management Corporation ponen esta información a disposición del consumidor en nuestras etiquetas de emisiones.
Page 88
Las siguientes son disposiciones específicas relacionadas con la cobertura de la garantía para defectos en el control de emisiones. Es un añadido a la garantía de motor Sears para motores no regulados que se encuentra en las instrucciones de funcionamiento y mantenimiento.
Page 89
DECLARACIÓN FEDERAL y/o DE CALIFORNIA SOBRE GARANTÍAS EN EL CONTROL DE EMISIONES SUS DERECHOS Y OBLIGACIONES EN CUANTO A LA GARANTÍA MTD Consumer Group Inc, la Agencia de Protección Medioambiental de los Estados Unidos (EPA), y para aquellos productos certificados para su venta en el es- tado de California, el Departamento de los Recursos del Aire de California (CARB) se complacen en explicar la garantía que cubre al sistema de control (ECS) de emisiones (evaporativas y/o de escape) de su equipo y motor (motor de equipos de exteriores) de encendido por chispa para todo terreno, pequeño, de exteriores del año 2006 y años posteriores En California, los nuevos motores de equipos de exteriores deben estar diseñados, construidos y equipados para cumplir con las...
Page 90
8. Durante la totalidad del período de garantía del motor y equipo para todo terreno arriba mencionado, MTD Consumer Group Inc mantendrá un suministro de piezas bajo garantía suficiente para satisfacer la demanda esperada de tales piezas. 9. Cualquier pieza de reemplazo se podrá usar para el cumplimiento del mantenimiento o las reparaciones bajo garantía y se suministrarán sin cargo para el propietario.
Page 91
El *Coverage en Canadá varía en algunos artículos. Para detalles llenos la llamada Chamusca Canadá en 1-800- 361-6665. Servicio de instalación de Sears Si desea solicitar la instalación profesional de Sears de aparatos domésticos, dispositivos para abrir portones, calentado- res de agua y otros artículos domésticos importantes, en los Estados Unidos o Canadá llame al 1-800-4-MY-HOME®.
Page 92
® Registered Trademark / Trademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries ® Marca Registrada / Marca de Fábrica de KCD IP, LLC en Estados Unidos, o Sears Brands, LLC in otros países...
Need help?
Do you have a question about the Craftsman 247.288853 and is the answer not in the manual?
Questions and answers