Carrier AQUASNAP 61AF Operating Instructions Manual

Carrier AQUASNAP 61AF Operating Instructions Manual

Hide thumbs Also See for AQUASNAP 61AF:

Advertisement

61AF
Pro-Dialog+ Control
Operating instructions
\\MAINMENU\STATUS
CAPB_T
0 %
DEM_LIM
100 %
SP
4.2 °C
CTRL_PNT
-28.9 °C
EMSTOP
dsable
Circuit B Total Capacity
START/STOP
ENTER
PRO-DIALOG+

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AQUASNAP 61AF and is the answer not in the manual?

Questions and answers

Summary of Contents for Carrier AQUASNAP 61AF

  • Page 1 61AF Pro-Dialog+ Control \\MAINMENU\STATUS CAPB_T DEM_LIM 100 % 4.2 °C CTRL_PNT -28.9 °C EMSTOP dsable Circuit B Total Capacity START/STOP ENTER PRO-DIALOG+ Operating instructions...
  • Page 2: Table Of Contents

    Contents 1 - SAFETY CONSIDERATIONS ............................... 3 1.1 - General ..................................... .3 1.2 - Avoid electrocution ................................. .3 2 - GENERAL DESCRIPTION ..............................3 2.1 - General ..................................... .3 2.2 - Abbreviations used.................................. .3 3 - HARDWARE DESCRIPTION ............................... 3 3.1 - General .....................................
  • Page 3: Safety Considerations

         2.2 - Abbreviations used 1.1 - General In this manual, the compressors are labelled A1 and A2. Installation, start-up and servicing of equipment can be The following abbreviations are used frequently: hazardous if certain factors particular to the installation are #ARRIER #OMFORT .ETWORK not considered: operating pressures, presence of electrical Light Emitting Diode...
  • Page 4: Electrical Supply To Boards

    Á¿Íʽ ÇÆÌÊÇÄ ºÇ¹Ê¼ Green LED Unit has stopped Unit starts up Contrast control Unit in operation wheel Back to the previous Red LED screen No alarm Warning Circuit or complete unit error È ÇÏÆ Ã½Ñ - Navigation ǼÁ »¹ÌÁÇÆ Æ Ç Ã½Ñ ÆÌ½Ê...
  • Page 5    »ÇÆÌÊÇÄ ºÇ¹Ê¼ ÈÌÁÇÆ¹Ä   ºÇ¹Ê¼ J7A J7B J8 NRCP2-BASE board connections ÇÆÆ½»ÌÇÊ »À¹ÆÆ½Ä ÑȽ ½ÊÅÁÆ¹Ä ½Ë»ÊÁÈÌÁÇÆ CH 08/J4 32-33 ½ÅÇ̽ ÇÆ Ç ËÏÁÌ»À CH 09/J4 ÍËÌÇÅ½Ê Ë¹¾½ÌÑ ÄÇÇÈ ÁÆÈÍÌ ¾¹ÍÄÌ CH 10/J4 73-74 ¹È¹»ÁÌÑ ÄÁÅÁ̹ÌÁÇÆ ˽Ľ»ÌÁÇÆ CH 12/J5 Setpoint selection CH 13/J5...
  • Page 6: Setting Up Pro-Dialog+ Control

    4.        Enter password 4.1 - General features 1_** À½ ÊËÌ ¼Á¿ÁÌ ÁË ÌÀ½ »ÍÊËÇÊ ÁË positioned on the second digit The interface includes different screens that are listed below: º¹ËÁ» ¹»»½ËË $EFAULT SCREENS WITH DIRECT DISPLAY OF THE MAIN parameters, -ENU SCREENS FOR NAVIGATION $ATACONlGURATION SCREENS LISTING THE PARAMETERS BY...
  • Page 7: Operating Mode Screen

    ATTENTION: If the user exits from the current data screen, \\MAINMENU\TEMP Current path in the menu structure THE VALUE IS SAVED ! SAVING CONlRMATION IS DISPLAYED 40°C List of items 4HE %NTER KEY VALIDATES THE PARAMETER MODIlCATION S  46°C Cursor position The Return to the Previous Screen key cancels the current 4°C...
  • Page 8: Menu Tree Structure

    4.8 - Menu tree structure...
  • Page 9: Detailed Menu Description

    ½Ì¹ÁĽ¼ ŽÆÍ ¼½Ë»ÊÁÈÌÁÇÆ ATTENTION: Depending on the unit characteristics, certain menu items are not used. 4.9.1 - GENUNIT menu         CTRL_TYP 0/1/2 ÇÆÌÊÇÄ ÅǼ½ ÌÑȽ STATUS Operating status min_left 0-15 ̹ÊÌ ÍÈ ¼½Ä¹Ñ LSP_SEL 0/1/2 Setpoint selection via the interface...
  • Page 10 4.9.5 - INPUTS menu        ONOFF_SW Open/Close Remote start/stop contact SETP_SW Open/Close Remote setpoint contact LIM_SW1 Open/Close ½ÅÇ̽ »¹È¹»ÁÌÑ ÄÁÅÁ̹ÌÁÇÆ »ÇÆÌ¹»Ì FLOW_SW Open/Close ¹Ì½Ê ÇÏ Ê¹Ì½ »ÍËÌÇÅ½Ê Ë¹¾½ÌÑ ÄÇÇÈ »ÇÆÌ¹»Ì leak_v nn.n Volt Leak detector value Lock_sw2 Open/Close ÍËÌÇŽÊ...
  • Page 11 4.9.11 - ALARMRST menu        RST_ALM Yes/No Alarm reset Normal Alarm status alarm_1c nnnnn Current alarm 1 alarm_2c nnnnn Current alarm 2 alarm_3c nnnnn Current alarm 3 alarm_4c nnnnn Current alarm 4 alarm_5c nnnnn Current alarm 5 alarm_1 nnnnn...
  • Page 12 4.9.17 - GENCONF menu         ramp_sel Yes/No Ramp loading sequence Ç ÇÆ ¼ 1 to 15 ̹ÊÌ ÍÈ ¼½Ä¹Ñ nh_start 00:00 to 24:00 00:00 Night mode start hour nh_end 00:00 to 24:00 00:00 Night mode stop hour bas_menu 0 to 3...
  • Page 13 Time schedule type: 4.9.24 - OCC1PSX menu The control provides two timer programs: MON: ÇÆ¼¹Ñ Time 4HE lRST TIMER PROGRAM .O  PROVIDES A MEANS TO AUTO TUE: ͽ˼¹Ñ matically switch the unit from an occupied mode to an WED: ½¼Æ½Ë¼¹Ñ...
  • Page 14 ÇÆ ¿ÍʹÌÁÇÆ ŽÆÍ ¾ÇÊ Ç»»ÍÈÁ½¼ ¹Æ¼ ÍÆÇ»»ÍÈÁ½¼ ȽÊÁÇ¼Ë         OVR_EXT hours Occupied schedule override DOW1 11111111 ½ÊÁǼ ¼¹Ñ Ǿ ÌÀ½ Ͻ½Ã   ÇÆ¼¹Ñ ͽ˼¹Ñ ½¼Æ½Ë¼¹Ñ ÀÍÊ˼¹Ñ ÊÁ¼¹Ñ ¹ÌÍʼ¹Ñ ÍÆ¼¹Ñ ÇÄÁ¼¹Ñ OCCTOD1 0:00-24:00 00:00 Occupied from UNOCTOD1 0:00-24:00...
  • Page 15: Pro-Dialog Plus Control Operation

           Command set to Stop: the unit is halted. Command set to Start: the unit runs in accordance ̹ÊÌ ËÌÇÈ »ÇÆÌÊÇÄ with schedule 1. Start/Stop schedule: occupied or unoccupied status of The table below summarises the unit control type and stop the unit as determined by the unit start/stop program or go status with regard to the following parameters.
  • Page 16: Capacity Limitation

    ¹È¹»ÁÌÑ ÄÁÅÁ̹ÌÁÇÆ 5.5.1 - Active setpoint 4WO SETPOINTS CAN BE SELECTED FOR THE HEATING MODE 5SUALLY the second setpoint is used for unoccupied periods. Capacity limitation is used to restrict the unit power consumption. The Pro-Dialog control system allows limitation of the unit capacity, using user-controlled volt- Depending on the current operating type, the active setpoint can be selected: free contacts.
  • Page 17: Additional Electric Heater Stage Control

    ¼¼ÁÌÁÇÆ¹Ä ½Ä½»ÌÊÁ» À½¹Ì½Ê Ë̹¿½ »ÇÆÌÊÇÄ ¹ËÌ½Ê ËĹν ¹Ë˽źÄÑ As an option, the heat pump units can control up to four Two Pro-Dialog+ units can be linked to produce a master/ additional electric heating stages. slave assembly. The two machines are interconnected over THE ##.
  • Page 18: Diagnostics - Troubleshooting

           4HE LEAD MACHINE WILL ALWAYS BE STARTED lRST 7HEN THE lead machine is at its full available capacity, start-up delay CONlGURABLE IS INITIALISED ON THE FOLLOWER 7HEN THIS DELAY 6.1 - General has expired, and if the error on the control point is greater The Pro-Dialog+ control system has many fault tracing aid than 1.7°C, the follower unit is authorised to start and the pump is activated.
  • Page 19: Alarm Codes

    ĹÊÅ »Ç¼½Ë ĹÊŠĹÊŠĹÊÅ ¼½Ë»ÊÁÈÌÁÇÆ ½Ë½Ì ÌÑȽ ÊǺ¹ºÄ½ »¹Í˽ »ÌÁÇÆ Ì¹Ã½Æ ºÑ ÌÀ½ »ÇÆÌÊÇÄ Ç code À½ÊÅÁËÌÇÊ ¾¹ÍÄÌË th-01 ½ÆËÇÊ ¾¹ÍÄÌ ÍÁ¼ ½ÆÌ½ÊÁÆ¿ Ï¹Ì½Ê À½¹Ì Automatic when the temperature Defective thermistor Unit is shut down ½Ð»À¹Æ¿½Ê ޹ËÍʽ¼ ºÑ ÌÀ½ ˽ÆËÇÊ Ê½ÌÍÊÆË ÌÇ ÆÇÊÅ¹Ä th-02 ½ÆËÇÊ...
  • Page 20 ĹÊÅ »Ç¼½Ë »ÇÆÌÁÆÍ½¼ ĹÊÅ Ç Ä¹ÊŠĹÊÅ ¼½Ë»ÊÁÈÌÁÇÆ ½Ë½Ì ÌÑȽ ÊǺ¹ºÄ½ »¹Í˽ »ÌÁÇÆ Ì¹Ã½Æ ºÑ ÌÀ½ »ÇÆÌÊÇÄ code ÊÇ»½ËË ¾¹ÍÄÌË »ÇÆÌÁÆÍ½¼ FC-nn ÄĽ¿¹Ä ¾¹»ÌÇÊÑ »ÇÆ ¿ÍʹÌÁÇÆ Manual À½ ÍÆÁÌ ËÁÒ½ À¹Ë º½½Æ »ÇÆ ¿Íʽ¼ Unit is shut down number with the wrong value Sr-nn Maintenance alert Manual...
  • Page 22 Order No. 16112-76, 05.2014. Supersedes order No.: 16112-76, 01.2013. ¹ÆÍ¾¹»ÌÍʽ¼ ºÑ ¹ÊÊÁ½Ê   ÇÆÌÄÍ½Ä Ê¹Æ»½ ¹ÆÍ¾¹»ÌÍÊ½Ê Ê½Ë½ÊÎ½Ë ÌÀ½ ÊÁ¿ÀÌ ÌÇ »À¹Æ¿½ ¹ÆÑ ÈÊÇ¼Í»Ì ËȽ»Á »¹ÌÁÇÆË ÏÁÌÀÇÍÌ ÆÇÌÁ»½ ÊÁÆÌ½¼ ÁÆ ÌÀ½ ÍÊÇȽ¹Æ ÆÁÇÆ...

Table of Contents