Mitsubishi Heavy Industries FDF71VNXWVH Service Manual page 27

(35) Motion sensor control (Option, RC-EX3A and RCN-E2 only)
The sensor determines the presence of people and the amount of activity, and the following controls are done by the motion sensor.
Following settings are necessary to activate motion sensor control.
(a) Infrared (motion) sensor setting: Installation setting of remote control
Installed wired remote control
The indoor unit which is set to "Enable" become valid.
TOP screen Menu _ Service setting _ Installation settings _ Service password
(b) Infrared (motion) sensor control: Energy-saving setting of remote control
The function which is set to "Enable" become valid.
Installed wired remote control
16:14 (Mon)
Cooling Set temp
TOP screen Menu _ Service setting _ Installation settings _ Service password
Timer
Now stopping.
F1: High power F2: Energy-saving
16:14 (Mon)
Cooling Set temp
Timer
Now stopping.
F1: High power F2: Energy-saving
TOP screen Menu _ Energy-saving setting
The Motion sensor control screen and contents of the current settings are displayed.
Infrared sensor control
TOP screen Menu _ Energy-saving setting
Power control
Auto-off
Infrared sensor control
Power control
Auto-off
Select the item.
Select the item.
RCN-E2
1. Set indoor functions
①
Press the ON/OFF button to stop the unit.
②
Press the desired one of the buttons shown item 2. while holding down the
FUNCTION SETTING switch.
③
RCN-E2 Use the selection buttons, ▲ and ▼, to change the setting.
④
Press the SET button.
1. Set indoor functions
The buzzer on the remote control signal receiver beeps twice, and the LED
①
Press the ON/OFF button to stop the unit.
②
Press the desired one of the buttons shown item 2. while holding down the
FUNCTION SETTING switch.
2. Setting details
③
Use the selection buttons, ▲ and ▼, to change the setting.
④
Press the SET button.
Number
The buzzer on the remote control signal receiver beeps twice, and the LED
Button
indicator
00
2. Setting details
SILENT
01
00
Number
Button
indicator
01
HI POWER
00
02
SILENT
01
03
00
01
HI POWER
02
03
Installation settings menu #2
Menu
Installation settings
Direction
Address setting of main IU
IU back-up function
Infrared sensor setting
Installation settings menu #2
Menu
Installation settings
Direction
Address setting of main IU
Previous
IU back-up function
Select the item.
Infrared sensor setting
Previous
Select the item.
e S e l t c n E
Enable, the set temperature is gradually adjusted to ±3.0 based
Disable Enable
on the amount of activities.
Disable Enable
Tap Set temp in cool/heat
1
Disable Enable
2
Disable Enable
Set Back
1
s U t e e h
2
tap the
3
temperature. The allowable range is as follows:
Set Back
Cooling: 25 to 35°C (in unit of 1°C, Initial setting 33°C)
Heating: 10 to 20°C (in unit of 1°C, Initial setting 15°C)
3
If the amount of activities continues to be small, Set temp is
changed to the set temperature and the power of the air
conditioner is suppressed. "Power control ON" is displayed
when power is being controlled. Also, Set temp displays the
adjusted temperature.
e S e l t c n E
judges that there is no one around based on the amount of
activities. After one hour, the unit will be in the "Operation wait"
state.
Infrared sensor setting (Motion sensor setting) : Disable
Infrared sensor setting (Motion sensor setting) : Enable
Tap
Infrared sensor control (Motion sensor control) : Disable
Infrared sensor control (Motion sensor control) : Power control only
Infrared sensor setting (Motion sensor setting) : Disable
Infrared sensor control (Motion sensor control) : Auto OFF only
Infrared sensor setting (Motion sensor setting) : Enable
Infrared sensor control (Motion sensor control) : Power control and Auto OFF
Infrared sensor control (Motion sensor control) : Disable
Infrared sensor control (Motion sensor control) : Power control only
Infrared sensor control (Motion sensor control) : Auto OFF only
Infrared sensor control (Motion sensor control) : Power control and Auto OFF
Infrared (motion) sensor setting
Infrared sensor setting
Disable
Enable
Infrared (motion) sensor setting
Infrared sensor setting
Back
Disable
Select the item.
Enable
Back
Select the item.
Infrared sensor control
_
The Infrared sensor control screen and contents of the
current settings are displayed.
b a e l D / s i b a e l o f P r w o r e o c r t n . l o
①
Enable/disable power control.
Infrared sensor control
_
②
Enable/disable auto-off.
The Infrared sensor control screen and contents of the
③ .
After you set each item, tap the
current settings are displayed.
The display returns to the Energy-saving setting
①
Enable/disable power control.
menu screen.
②
Enable/disable auto-off.
③
After you set each item, tap the
The display returns to the Energy-saving setting
menu screen.
button to set the temperature, and
p q
Set button. Temporarily determine the set
b a e l D / s i b a e l r o f u A o t f o - I . f y f u o
Function setting
Standby time .
Function setting
26
- -
'22 • PAC-SM-426
Back
Back
or Motion sensor control
W h n e y u o e s e l t c
Motion sensor control
or
Set
button.
Set
button.
①
②
②
④
③
①
②
②
②
e s e l t c n E b a e l t , e h u t i n
④
③
②