Advertisement
Wiring Diagram - VX600/6i
+12 VDC - Positive (+12V) Battery Connection
Ground - Negative (–) Ground Connection
Remote - Positive (+12V) Turn-On Input From Source Unit
JLid-COMM - Optional Network Hub or
Bluetooth® Communicator Connection (Sold Separately)
JLid-CTRL - Optional Digital Remote Controller
(DRC) Connection (Sold Separately)
Input 6 - Ch. 6 Input
Input 5 - Ch. 5 Input
Input 4 - Ch. 4 Input
Input 3 - Ch. 3 Input
Input 2 - Ch. 2 Input
Input 1 - Ch. 1 Input
Pre-Out Right - Analog Preamp Output
Pre-Out Left - Analog Preamp Output
Remote - Turn-On Output (+12V)
Valet - Valet Preset Toggle (–)
Connections
Power Connector
Connection
Wire Capacity
Description
+12 VDC (+)
4 AWG
Positive (+12V) Power Connection to Battery
Ground (–)
4 AWG
Negative (GND) Chassis Ground Connection
Remote
18 to 10 AWG
Positive (+12V) Remote Turn-On Input from Source Unit
Analog Input Harness
Plug/Wire
Label
Description
Color
Input 1
White RCA
Channel 1 Signal Input
Input 2
Red RCA
Channel 2 Signal Input
Input 3
White RCA
Channel 3 Signal Input
Input 4
Red RCA
Channel 4 Signal Input
Input 5
White RCA
Channel 5 Signal Input
Input 6
Red RCA
Channel 6 Signal Input
Pre-Out Left
White RCA
Preamp Signal Output 1
Pre-Out Right
Red RCA
Preamp Signal Output 2
Remote
Blue
Positive (+12V) Turn-On Output (475 mA limit)
Valet
Green
Negative (GND) Ground Input (activates the Valet Mode Preset)
Speaker Output Harness
Label
Wire Color
Description
White
(+) Positive Speaker Output
Ch. 1&2 Bridged (+)
A
Ch. 1
White/Black
(–) Negative Speaker Output
Gray
(+) Positive Speaker Output
B
Ch. 2
Gray/Black
(–) Negative Speaker Output
Ch. 1&2 Bridged (–)
Green
(+) Positive Speaker Output
Ch. 3&4 Bridged (+)
C
Ch. 3
Green/Black
(–) Negative Speaker Output
Purple
(+) Positive Speaker Output
D
Ch. 4
Purple/Black
(–) Negative Speaker Output
Ch. 3&4 Bridged (–)
Cyan
(+) Positive Speaker Output
Ch. 5&6 Bridged (+)
E
Ch. 5
Cyan/Black
(–) Negative Speaker Output
Magenta
(+) Positive Speaker Output
F
Ch. 6
Magenta/Black
(–) Negative Speaker Output
Ch. 5&6 Bridged (–)
Data Connections
Label
Type
Description/Use
JLid-COMM
RJ45 Jack
Optional accessory connections (VXi-BTC, VXi-HUB, etc)
JLid-CTRL
RJ45 Jack
Optional DRC (Digital Remote Controller) connection
USB
USB A/B Port
Computer connection to configure TüN™ Software Interface
2-channel, optical (Toslink) digital input
DIGITAL-In
S/PDIF Port
DIGITAL-Out
S/PDIF Port
2-channel, optical (Toslink) digital output
Reset Buttons
Multifunction use (Reboot/Reset/Device Firmware Update mode)
SD + Reset
Micro SD Slot
Used for future expansion
Standard CAT5 Network Cables
Specifications
Amplifier Specifications
Amplifier Topology
2nd-Gen NexD™ High Speed Class D
Power Supply Type
Unregulated MOSFET Switching
Operating Voltage
10 - 15V DC
Min. Copper Power/GND Wire
4 AWG
Recommended Fuse
50 A
Standby Current Draw
2.4 mA
Input Voltage Range
200 mV - 16 V RMS
Rated RMS Power @ 14.4V,
75W x 6
100W x 6
<1% THD+N
@ 4 Ω
@ 2 Ω
Rated RMS Power @ 12.5V,
60W x 6
90W x 6
<1% THD+N
@ 4 Ω
@ 2 Ω
Frequency Response
12 Hz - 24 kHz (+0, -1dB)
S/N Ratio,
99 dB (Referred to rated power),
(A-weighted, 20 kHz
80 dB (Referred to 1 W)
noise bandwidth)
S/N Ratio,
99 dB (Referred to rated power),
(A-weighted, 20 kHz
80 dB (Referred to 1 W)
noise bandwidth)
Damping Factor
>100 / 50 Hz @ 4 Ω, >50 / 50 Hz @ 2 Ω
DSP Specifications
Processor
AKM AK7738, processing at 24 bit/96 kHz
Type
Line-Level, Differential-Balanced
Number of Channels
6, via harness-mounted female RCA jacks
Type
S/PDIF Optical via chassis-mounted Toslink port
Bit Depth/Sample Rate
Up to 24 bit/192 kHz
Type
2 Line-Level, via harness-mounted female RCA jacks
Max Output Level
4 V RMS
Type
S/PDIF Optical via chassis-mounted Toslink port
Bit Depth/Sample Rate
24 bit/96 kHz
Dimensions
L x W x H
9.81 in x 6.62 in x 2.12 in / 250 mm x 168 mm x 54 mm
ABCDEF
F - To Speaker(s): (+ and –)
E - To Speaker(s): (+ and –)
D - To Speaker(s): (+ and –)
C - To Speaker(s): (+ and –)
B - To Speaker(s): (+ and –)
A - To Speaker(s): (+ and –)
DIGITAL-In - From Optical Digital (S/PDIF) Source
Optical Audio Cables
DIGITAL-Out -
To Optical Digital (S/PDIF) Input on Next Device
USB A/B Cable -
To Computer with TüN™ software installed
Included
Not Included
What is TüN?
TüN™ is software that you use to configure, tune and control your VXi
amplifier, and other JL Audio DSP products. TüN™ automatically recognizes
what it is connected to, and allows you to make adjustments with a
clear interface specifically set up for that product. TüN™ is available for
download for free in a variety of applications, for computers and most
handheld devices. For more information, visit: jlaudio.com/tun
200W x 3
@ 4 Ω Bridged
180W x 3
For Windows® PC or Mac® computers, TüN™ connects via
@ 4 Ω Bridged
USB and offers complete control and command of the entire
VXi feature set from the comfort of your desk or driver's seat.
Software also runs in demo mode, without connected amplifiers,
for offline setup or demo purposes. Test drive it for free!
For iPad or Android tablets. Enjoy the full-featured TüN™ software
experience on your tablet, with the freedom of a wireless connection
via Bluetooth®. Requires VXi-BTC Bluetooth® Communicator.
Wireless connection and streamlined options, for fast and simple
amplifier setup. Download TüN™ Express for iPhone, iPad and Android
phones & tablets. Requires VXi-BTC Bluetooth® Communicator.
LED Status/Condition Reporting
LEDs located on the chassis top and connection panel are used to
communicate amplifier status and condition. Refer to the table below for
the location and meaning for each behavior.
LED / Location
Behavior
Flashing Blue
LED Ring /
Flashing Red
Amplifier Top
Flashing Yellow
Green
Upper Left LED /
Blue
JLid-COMM Port
and
Yellow
JLid-CTRL Port
Flashing Red
Upper Right LED /
Flashing Red
JLid-COMM Port
Upper Right LED /
Green
JLid-CTRL Port
SPEAKER
OUTPUTS
Limited Warranty – Amplifiers (USA)
JL Audio warrants this product to be free of defects in materials and workmanship
for a period of two (2) years from the original date of purchase. This warranty is
not transferable and applies only to the original purchaser from an authorized
JL Audio dealer. Should service be necessary under this warranty for any reason due
to manufacturing defect or malfunction, JL Audio will (at its discretion), repair or
replace the defective product with new or remanufactured product at no charge.
Damage caused by the following is not covered under warranty: accident, misuse,
abuse, product modification or neglect, failure to follow installation instructions,
unauthorized repair attempts, misrepresentations by the seller. This warranty does
not cover incidental or consequential damages and does not cover the cost of
removing or reinstalling the unit(s). Cosmetic damage due to accident or normal
wear and tear is not covered under warranty.
Warranty is void if the product's serial number has been removed or defaced.
Any applicable implied warranties are limited in duration to the period of the
express warranty as provided herein beginning with the date of the original
purchase at retail, and no warranties, whether express or implied, shall apply to
this product thereafter. Some states do not allow limitations on implied warranties,
therefore these exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights, which vary from state to state.
If you need service on your JL AUDIO product:
All warranty returns should be sent to JL Audio 's Amplifier Service Facility
freight-prepaid through an authorized JL Audio dealer and must be accompanied
by proof of purchase (a copy of the original sales receipt). Direct returns from
consumers or non-authorized dealers will be refused unless specifically authorized
by JL Audio with a valid return authorization number. Warranty expiration on
products returned without proof of purchase will be determined from the
manufacturing date code. Coverage may be invalidated as this date is previous
to purchase date. Non-defective items received will be returned freight-collect.
Customer is responsible for shipping charges and insurance in sending the
product to JL Audio. Freight damage on returns is not covered under warranty.
For Service Information in the U.S.A. please call
JL Audio Customer Service:
(954) 443-1100 9:00 AM – 5:30 PM (Eastern Time Zone)
JL Audio, Inc.
10369 North Commerce Pkwy. Miramar, FL 33025
(Do not send product for repair to this address)
International Warranties:
Products purchased outside the United States of America are covered
only by that country's distributor and not by JL Audio, Inc.
Status/Condition›
Critical Voltage
Critical Temperature
Excessive Current
Detecting JLid™ Device
JLid™ Connection Success
Invalid JLid™ Device
Excessive Current
Critical Voltage/Temperature
Excessive Remote Output Current
Active TüN™ Connection
VX600/6i_MAN_050219
Advertisement
