Related Manuals for Cortelco 730901-TP2-27F
Summary of Contents for Cortelco 730901-TP2-27F
- Page 1 2.4GHz CORDLESS CALLER ID TELEPHONE WITH CALL WAITING 40 CHANNEL AUTOSCAN 730901-TP2-27F OWNER'S MANUAL INSTALLATION AND OPERATING INSTRUCTIONS PLEASE READ THIS MANUAL CAREFULLY BEFORE USE. KEEP FOR YOUR REFERENCE.
- Page 2 Special Features ongratulations on your selection of a quality CORTELCO product . With proper care and by following the setup and user instructions in this manual, this unit will provide you with years of trouble free service . committed to providing quality products that fit your needs. We would like to have any comments or suggestions you might have on this product .You may mail...
- Page 3 Special Features Luminous LCD Screen - The LCD Screen emits light for 8 seconds every time you press any of the TELEPHONE KEYPAD buttons. HANDSET Ringer Volume Level - Select the ringer volume level (HI, LOW, OFF). HANDSET Volume Control Switch - Select the receiver volume level(HI.MID,LOW). HEADSET JACK - Your telephone can utilize a headset for hands-free communication BELT CLIP- Use the BELT CLIP to hang your HANDSET on your belt.
- Page 4 HANDSET Controls 1. HANDSET ANTENNA 2. NEW CALL/MESSAGE WAITING LED INDICATOR L D C C F CALLS BATT MSG DIR 3. LARGE LCD SCREEN SEC RPT SEC RPT TOTAL TOTAL 4.TALK BUTTON TALK 5. TEMPORARY TONE ( ) BUTTON 6. DIRECTORY BUTTON 7.
-
Page 5: Technical Information
HANDSET. Interference Electronic circuits activate a relay to connect the cordless telephone to your telephone line. These electronic circuits operate in the radio frequency spectrum. While several protection circuits are used to prevent unwanted signals, there may be periods when these unwanted signals enter the BASE UNIT. - Page 6 BASE UNIT CONTROLS 1. TELEPHONE LINE 2. POWER-IN CONNECTION JACK CONNECTION JACK pg.5,28 pg.5 2.4GHz I N U S E / C H A R G E I N U S E / C H A R G E 7.CHARGE TERMINALS Problem Solving Problem Solving section...
-
Page 7: Changing The Battery Pack
Changing the Battery Pack Changing the BATTERY PACK The BATTERY PACK provides power for the HANDSET of your cordless telephone. To Replace the BATTERY PACK: HANDSET 1. Remove the BATTERY COMPARTMENT COVER by sliding it down. 2. Pull out the BATTERY CONNECTOR PLUG and remove the BATTERY PACK. -
Page 8: Table Of Contents
Recharging the Battery Pack Battery Type Use the following type and size of BATTERY PACK: Cordless Telephone BATTERY PACK 3.6V, 600mAh NOTE: During a power interruption, the BASE UNIT does not operate, and a phone conversation cannot be made on the HANDSET. - Page 9 Security System Your cordless telephone uses a digital coding security system to prevent unauthorized use of your telephone line by another nearby cordless telephone. The system has its own identifying signal created by microcomputers in both the BASE UNIT and the HANDSET.
-
Page 10: Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of fire, electric shock and /or injury, always follow these basic safety precautions when using your cordless telephone equipment. 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the telephone. - Page 11 To reduce the risk of fire or personal injury, read and follow these instructions: 1. Use only the following type and size BATTERY PACK: Cordless Telephone BATTERY PACK 3.6V, 600mAh. Ni-MH BATTERY 2. Do not dispose of the BATTERY PACK in a fire. It may explode. Check with local codes for possible special disposal instructions.
-
Page 12: Getting Started
Return it to the place of purchase. 2. Check to be sure you have all items that come with this cordless telephone system. You should have a HANDSET , BASE UNIT, AC ADAPTOR, TELEPHONE LINE CORD, SHORT TELEPHONE LINE CORD ,BELT CLIP and Owner's Manual. -
Page 13: C. Ringer Volume
Caller ID System Operation 6. Press the button to return to the STANDBY mode. / VOICE MAIL NOTE: The date and time will automatically set, if you have subscribed to the Caller ID service from your local telephone company. C. RINGER VOLUME This function enables you to adjust the ringer volume from HI, LOW and OFF as desired. -
Page 14: A. Language
CLIP until the other hook locks Into the slot on the side of the HANDSET. 13. Set the date and time. You are now ready to use your new CORTELCO Cordless Telephone IMPORTANT In order to utilize the Caller ID feature, you must subscribe to Caller ID service from your local telephone company. -
Page 15: Cordless Telephone Operation
Cordless Telephone Operation Preparing for Use Before you can use cordless telephone ,you must charge the HANDSET for 12 hours. Failure to do so will require recharging of the BATTERY PACK more often. (See page 26 for more information on the BATTERY PACK) 1. -
Page 16: Placing Calls
Cordless Telephone Operation Placing Calls 1. Press the button, the Call Timer starts to count. The HANDSET LCD Screen will display "CALLS " and "TALK ", and the BASE UNIT IN USE LED indicator will light 2. Listen for a dial tone. -
Page 17: Using The Headset Feature
NOTE: If the phone company does not supply all ten digits of an incoming caller, you will not be allowed to adjust the format of that number. Cordless Telephone Operation Using the Headset Feature Your telephone can utilize a headset (not included) to be connected to your HANDSET for you to enjoy hands-free communication. -
Page 18: Caller Id System
Caller ID System Operation Caller ID System This telephone automatically displays an incoming caller's name and telephone number together with the date and time of the call. It records up to 80 calls and stores the data in Memory. IMPORTANT: You must subscribe to the Caller ID service from your local telephone company to utilize this feature. -
Page 19: Call Waiting
Caller ID System Operation Saving in the PHONE BOOK 1. Press the button. The LCD screen will display "PHONE BOOK".(a record will be displayed if the phone book is full, the phone book can story up to 64 records) /FLASH EDIT 2. -
Page 20: Viewing The Caller List
Caller ID System Operation Viewing the Caller List 1. Press the SCROLL DOWN button to view the latest Caller ID record, or press the SCROLL UP button to view the first Caller ID record, press the SHIFT RIGHT button if the name has more than 11 digits. 2.