Advertisement
Quick Links
Models:
WF219ANW/XAA
WF219ANB/XAA
Quick Test Mode
Note: This test erases all faults and memory
To enter press Spin, Soil, & Power
simultaneously with the power off.
1. All LED's light up and the washer beeps as it
enters the Quick Test Mode.
2. The unit displays the software then clears the
EEprom.
3. After the displaying the software version, Jog
dial CCW to display "F4"
If EEEE is displayed the PCB ass'y is defective.
4. When the model version (F4) is displayed. Press
the following keys to test the various components
Press Temp Key to cycle through the Water Valves
circuit test in this order: Cold Main, Bleach, Cold Main
& Bleach for Fabric Softener, Hot, then off.
Press Spin Key to test the motor
Press Soil Level to test Door Lock/Unlock circuit.
Press Signal Key to test the Pump
Location considerations
Do not install your washer in areas where
water may freeze, since your washer will
always maintain some water in its water
valve, pump, and hose areas. This can cause
damage the belts, the pump, hoses and other
components. Operating temperature should
be above 60°F/16°C.
Fast Track Troubleshooting
IMPORTANT SAFETY NOTICE – "For Technicians Only" This service data sheet is
intended for use by persons having electrical, electronic, and mechanical experience
and knowledge at a level generally considered acceptable in the appliance repair trade.
Any attempt to repair a major appliance may result in personal injury and property
damage. The manufacturer or seller cannot be responsible, nor assume any liability for
injury or damage of any kind arising from the use of this data sheet.
:
Publication # tsWF219 Revision Date 1/15/2010
Service Mode:
This mode allows more detailed operation tests and trouble-
shooting, to enter press Signal & Extra Rinse
simultaneously with the power on.
While in Service Mode the following tests can be performed:
Quick Spin Test = Delay Start & Spin: This
the drum motor from 0 to maximum RPM over a few min-
utes.
Note: Stay with the washer during this test, out of bal-
ance detection is bypassed and the door may not lock.
Press the Start/Pause button during the test to hold its spinning
speed for 10 minutes before going back to Quick Spin Test
Mode.
Cycle Count = Press the Signal button to see how many times
the unit was used
Soft Ware # = Press the Soil button to see the software version
information
Fast Time Down = Press the Temp button to advance to the
next cycle
Fault Code Test = Press the Spin button to view the stored fault
codes – then turn Dial to view error codes (Push Start/Pause
while the code is displayed to view the number of cycles since
the error occurred)
Peripheral (Main PCB) input Tests
1. Select Extra Wash. Then turn the Dial so that the Normal is
turned on. Next, press the Start/Pause Key. The Water
Temperature will be displayed in Fahrenheit.
2. Select Extra Wash. Then turn the Dial so that the White is
turned on. Next, press the Start/Pause Key. The door status will
be displayed (OP if open, CL if closed).
3. Select Extra Wash. Then turn the Dial so that the Wool is
turned on. Next, press the Start/Pause Key. The door lock
Switch status will be displayed (UL if unlocked, Lo if locked).
4. Select Extra Wash. Then turn the Dial so that the Perm Press
is turned on. Next, press the Start/Pause Key. The Water
Frequency will be displayed.
accelerates
1
Advertisement
Related Manuals for Samsung WF219ANW/XAA
Summary of Contents for Samsung WF219ANW/XAA
- Page 1 Models: and knowledge at a level generally considered acceptable in the appliance repair trade. WF219ANW/XAA Any attempt to repair a major appliance may result in personal injury and property WF219ANB/XAA damage.
- Page 3 Washer Connector Checks WF219 CN10 1 Main Valve (Blu) 2 Hot Valve (Red) 4 Bleach Valve (Pnk) RY9 Washer Heater Relay 1 Motor Pwr U Phase (Blu) 6 Drain Pump (Blk) 1 Heater (Red) 2 Motor Pwr V Phase (Wht) 7 Door Lock Close (Sky) 2 (N) (White) 3 Motor Pwr W Phase (Red)
- Page 4 Door Lock Check Test 1 Test 2 Connector CN5 Pin 3 (Blue) and CN10 Pin 7 (S/ When Door is Locked or Unlocked With Power Off, the resistance Blue) there is a pulse of 120VAC for a few between these pins will be between milliseconds.
- Page 5 Error Type Error Mode Details Check for Foreign material entering the pump or hoses. Drain Error Check to make sure the wiring harness is connected properly. Check the water pump terminal . Check for freezing Make sure to check the operating voltage. (An error occurs when Power Error under or over voltage is supplied.) Check whether a plug recepta- cle is used.
- Page 6 Error Type Error Mode Details This can be a short or a wire disconnected to the heater circuit. This Heater Error can also be problem with the tub contacting the heater or if the wa- ter in the tub is frozen or there is no water. The error is triggered by temperatures above 145C.
- Page 7 Stacking Kit : (Model SK-3A1/XAA SK-4A/XAA Samsung washers and dryers can be stacked to maximize usable space. An optional stacking kit is available for purchase from your Samsung retailer When using non-HE detergents, or using too much detergent for the water hard-...