Download Print this page

CP Plus ORANGE CP-UVK-711M User Manual

Villa indoor monitor

Advertisement

Quick Links

Villa Indoor Monitor
User Manual
Version 2.0.1

Advertisement

loading
Need help?

Need help?

Do you have a question about the ORANGE CP-UVK-711M and is the answer not in the manual?

Questions and answers

Summary of Contents for CP Plus ORANGE CP-UVK-711M

  • Page 1 Villa Indoor Monitor User Manual Version 2.0.1...
  • Page 2 Foreword General This Quick Start Guide (hereinafter referred to be "the Guide") introduces the functions, installation, and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the guide. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury.
  • Page 3 About this Guide • The Guide is for reference only. If there is inconsistency between the Guide and the actual product, the actual product shall prevail. • We are not liable for any loss caused by the operations that do not comply with the Guide. •...
  • Page 4 Important Safeguards and Warnings Electrical safety • All installation and operation should conform to your local electrical safety codes. • The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited power Source requirement according to IEC60950-1. Please note that the power supply requirement is subject to the device label.
  • Page 5 • Dome cover is an optical component, do not touch or wipe the cover with your hands directly during installation or operation. For removing dust, grease or fingerprints, wipe gently with moisten oil- free cotton with diethyl or moisten soft cloth. You can also air blower to remove dust. •...
  • Page 6 Cybersecurity Recommendations Cybersecurity is more than just a buzzword: it’s something that pertains to every device that is connected to the internet. IP video surveillance is not immune to cyber risks but taking basic steps toward protecting and strengthening networks and networked appliances will make them less susceptible to attacks.
  • Page 7 Enable HTTPS We suggest you to enable HTTPS, so that you visit Web service through a secure communication channel. Enable Whitelist We suggest you to enable whitelist function to prevent everyone, except those with specified IP addresses, from accessing the system. Therefore, please be sure to add your computer’s IP address and the accompanying equipment’s IP address to the whitelist.
  • Page 8 Establish the 802.1x access authentication system to reduce the risk of unauthorized ⚫ access to private networks. It is recommended that you enable your device's firewall or blacklist and whitelist feature ⚫ to reduce the risk that your device might be attacked.
  • Page 9 Table of Contents Cybersecurity Recommendations ......................II 1 Initialization ............................. 6 2 Login Interface .................... Error! Bookmark not defined. 2.1 Login ....................Error! Bookmark not defined. 2.2 Resetting Password ................ Error! Bookmark not defined. 3 Main Interface ....................Error! Bookmark not defined. 4 Local Setting ....................
  • Page 10 1 Product Overview 1.1 Introduction A digital VTH is device that can perform monitoring, voice/video call and door unlock. 1.2 Function Wi-Fi Networking Connect to Wi-Fi Networks. Video/Voice Call Make video or voice call to other VTOs and VTHs Monitoring Monitor fence station, VTO and IPC devices (Only supported by certain models) Make emergency call to the call centre.
  • Page 11 2 Network Diagram 2.1 2-wire system...
  • Page 12 Digital System There are two types of digital system network • The VTH powered through PoE from the floor switch.
  • Page 14 3. Preparation and Commissioning Carry out commissioning to ensure that the device can realize basic network access, call and monitoring functions. 3.1. Preparation Before commissioning: Power on the device only after there is no short or open circuit. ⚫ Plan IP addresses and numbers (works as phone numbers) for every VTO and VTH. ⚫...
  • Page 15 Set an email address Select Email and enter your email address for resetting password. Click Next. Initialization successful Click OK and the it jumps to the login interface.
  • Page 16 Login interface Enter username (admin by default) and password, and then click Login. 3.1.1.2. Network Parameters Change the IP address of the VTO to the one that you planned. Select Network Setting > Basic. TCP/IP Enter the parameters, and then click OK. The VTO automatically restarts.
  • Page 17 Wait for the device to automatically restart or restart it manually, and then the settings will take effect. 3.1.1.4. Server Type You can select the type of the server that manages all VTO devices. Select Network Setting > SIP Server. SIP server (1) Select a server type.
  • Page 18 Disable SIP Server, configure the parameters, and then click OK. The VTO automatically restarts, and it jumps to the login interface. 3.1.1.5.1.1.1.1.1 SIP server parameters when a VTO works as the SIP server Parameter Description IP Address IP address of the VTO that works as the SIP server. Port 5060 by default.
  • Page 19 3.1.1.5.1.1.1.3 Add a VTO Configure the parameters. 3.1.1.5.1.1.1.3.1 Parameters of adding a VTO Parameter Description Rec No. VTO number. Register Password Keep it default. IP Address IP address of VTO. Username Web interface login username and password of this VTO. Password Click OK.
  • Page 20 3.1.1.7.1.1.1.2 Add a VTH Configure the parameters. 3.1.1.7.1.1.1.2.1 Parameters of adding a VTH Parameter Description First Name Last Name Information to distinguish each device. Nick Name VTH number consists of 1–6 numbers, which may include number ⚫ and #. It must be consistent with room number configured at the VTH.
  • Page 21 3.1.2. VTH Settings 3.1.2.1. Initialization Select a region and language. Select a region and language Select Apartment or Villa, and then tap OK. This section takes Villa as an example. Select apartment or villa Select First-time Config and tap OK.
  • Page 22 First-time configuration DHCP is selected by default, or select Static IP and configure the parameters as needed. DHCP...
  • Page 23 Static IP Set a password and an email address for the VTH, and then tap Next. The password is used to enter project setting. ⚫ If you select Apartment in Step 6, initialization is completed with this step. ⚫ Set a password an email address for the VTH Set a password and an email address for the VTO.
  • Page 24 Set a password an Email address for the VTO Click Initialize to initialize a single device or Batch Initialization to initialize all available devices, and then click Next. Initialize devices Click One-key Config to go to the main interface.
  • Page 25 Network configuration Main interface 3.1.2.2. Network Parameters IP addresses of all VTHs and VTOs must be in the same network segment. Otherwise, the VTH will fail to obtain VTO information. On the main interface, tap Setting for more than 6 seconds. Enter the password and tap OK.
  • Page 26 WLAN ⚫ Only certain models support WLAN function. The actual product shall prevail. ⚫ Use a router with secured encryption protocols. ⚫ Turn on the WLAN function. WLAN Connect to a network. The system has 2 access ways as follows. Tap Wireless IP and enter Local IP, Subnet Mask and Gateway, and then tap ◇...
  • Page 27 Enable the DHCP function 3.1.2.3. VTH Config On the main interface, tap Setting for more than 6 seconds. Enter password and tap OK. Tap VTH Config. VTH configuration Configure VTH information. As a main VTH. ⚫ Enter the room number (such as 9901 or 101#0) and other information, and then tap OK.
  • Page 28 When there are extension VTHs, room numbers must end with #0. Otherwise, it ⚫ will fail to connect to the VTO. As an extension VTH. ⚫ Switch Main to Extension. Enter the room number (such as 101#1), Main VTH IP (IP address of the main VTH) and other information, and then tap OK.
  • Page 29 Table 1-1 SIP server parameters Parameter Description When a platform works as the SIP server, it is the IP address of the platform. Server IP When a VTO works as the SIP server, it is the IP address of the VTO.
  • Page 30 Add sub VTO or fence station. ⚫ Enter the sub VTO or fence Station name, IP address, username and password. Turn on Enable Status. to turn page and add more sub VTO or fence stations. 3.1.2.6. Searching Device You can search for VTOs in the same network, and then add them or change their information. Tap Search Device.
  • Page 31 Add a VTO Click Change IP to change the information of the VTO, including IP, netmask, and ⚫ gateway. Username and password cannot be changed here. They are the same as the ones used to log in to the web interface of the VTO, and are used to log in to the VTO. Change the information of the VTO device 3.2.
  • Page 32 Calling interface 3.2.2. VTH Monitoring VTO VTH can monitor VTO, fence station or IPC. This section takes monitoring VTO as an example. On the main interface of the VTH, tap Monitor > Door, and then tap a VTO to enter monitoring image.
  • Page 33 Monitoring image SD card is needed for recording and snapshot; otherwise, the icons will be gray.
  • Page 34 4. Interface Operation Main Interface Main interface Main interface description Name Description Room Number of the room where the VTH is located. number View, delete and clear announcements or security alarm information. When the VTH does not have an SD card, and the video-audio message uploading function is enabled on the VTO, three tabs will be Info...
  • Page 35 Name Description : Not connected to the network. : Connected to the network through a cable. : Wirelessly connected to the network. : Failed to connect to the main VTO; when disappeared, the device has connected to the Status main VTO. : An SD card has been inserted into the device;...
  • Page 36 Clear: Clear all record in the current tab (All or Missed Call). If storage is full, the oldest records will be overwritten. Back up the records as needed. Contact Tap Call > Contact, and then add or edit the users. Contact Add a user.
  • Page 37 Edit user information: Tap a user and tap Edit. Delete a user: Tap Edit, select a user, and then tap Delete. You can select multiple contacts at the same time. Call User Make sure that resident-to-resident call function has been enabled. See "0 QR Code" for details. Call function is used by VTH to call VTH.
  • Page 38 Calling Call in progress From Contact Add contacts first. See 0 Contact. Select Call > Contact. Select the one you want to call. to start. Call from User When receiving calls from other VTHs, the following interface will be displayed. Call interface (1)
  • Page 39 : Answer. : Hang up. Call interface (2) Call from VTO Dial VTH room no. (such as 9901) at VTO, to call VTH. On the VTH interface, tap Answer. Call from VTO...
  • Page 40 Interface description Description Remotely unlock the door where the VTO is installed. The system provides 2-channel unlock. If the icon is gray, it means that the unlock function of this channel is not available. Tap to talk to the VTO. Select an IPC in Favorite to monitor.
  • Page 41 Information in Security Alarm and Publish Info is stored in the device, and the one in Guest Message and Video Pictures is stored in the SD card, which means you need an SD card for these two functions. Only certain models support SD card. If the storage in the Device or SD card is full, the oldest records will be overwritten.
  • Page 42 Guest Message Select Info > Guest Message, and then you can view and manage all messages. Guest message Publish Info Select Info > Publish Info, and then you can view and manage all messages. Publish info...
  • Page 43 Video Pictures Select Info > Video Pictures, and then you can view and manage the pictures and videos. Records Monitor You can monitor VTO, fence station or IPC on the VTH. Monitoring VTO When adding VTOs, make sure that the username and password of each device is consistent with the web login username and password.
  • Page 44 Door Function description Icon Description Add the VTO or fence station to Favorite. Select an IPC, and when this VTO or fence station calls, you will see the monitoring image from this IPC. Add an IPC first. See 0 Adding IPC for details. Display the serial number of the VTO or fence station in QR code.
  • Page 45 Interface description Icon Description Remotely unlock the door where the VTO is located. The system provides 2-channel unlock function. If the icon is gray, it means that unlock function of this channel is not available. Take snapshot. An SD card is needed to use this function. Tap to start recording, and it will stop when the call is completed or by tapping If the SD card is full, the oldest videos will be overwritten.
  • Page 46 You can tap to add the IPC to Favorites. Tap Add. Add IPC Configure the parameters. Parameter description...
  • Page 47 Parameter Description Select IPC or NVR. IPC32 Name of the IPC/NVR. Name IP address of the IPC/NVR. User Name Web interface login username and password of the IPC/NVR. Password Port 554 by default. Main stream: High definition that needs large amount of bandwidth.
  • Page 48 Please monitor the VTO by reference to 0. Favorite Displays VTO, fence stations or IPC that have been added to favorites. To view favorite list, please ensure that VTO, fence station or IPC have been added to favorites. Otherwise, the list is empty. Select Monitor >...
  • Page 49 The system displays monitoring interface. In case of multiple devices in Favorite tab, tap to switch and monitor them. Please ensure that management center has been connected. Otherwise, it will fail to call. In emergency, press the SOS button on the device front panel, or tap SOS on the main interface to call management center.
  • Page 50 Tap text box to select rings, and tap to set the volume. VTH Ring Set the ring for this VTH. Tap Setting. The system pops up Password prompt box. Input login password and tap OK. Default login password is 123456. Please refer to 0 Password Setting for details. Select Ring >...
  • Page 51 Tap text box to select rings, and tap to set the volume. Alarm Ring Set the ring when the VTH gives an alarm. Tap Setting. Enter login password and tap OK. Default login password is 123456. Please refer to 0 Password Setting for details. Select Ring >...
  • Page 52 to set the time or volume. Tap to enable Ring Mute, and the icon becomes VTO ring time: ring time when a VTO calls this VTH. VTH ring time: ring time when another VTH calls this VTH. Card Information Issue and manage card information. This function is only available under Villa.
  • Page 53 Click Issue Card. Swipe the card on the corresponding VTO. The card information will be added to the VTH. Assign unlock permission by selecting Lock 1 and Lock 2 as needed. Click Confirm. Click Delete to delete the card information. Alarm Setting Set wire zone, wireless zone and alarm output.
  • Page 54 Parameter Description Area The number cannot be modified. Select NO (normally open) or NC (normally closed) according NO/NC to detector type. It shall be the same as detector type. Select corresponding type according to detector type, Type including IR, gas, smoke, urgency btn, door, burglar alarm, perimeter and doorbell.
  • Page 55 Tap Add. Tap wireless code button of wireless device. See wireless device user’s manual for details. After successful coding, display area info. Tap corresponding positions to set alarm status, enter delay and exit delay. See 0 for details. Tap Edit to select a zone and Delete to delete the selected area. Alarm Output After enabling alarm output, when other devices call this VTH, the alarm output device will output alarm info.
  • Page 56 to enable alarm output function, and the icon becomes Mode Setting Set area on/off status under different modes. Area mode can be set only in disarm status. Tap Setting. Enter login password and tap OK. Default login password is 123456. Please refer to 0 Password Setting for details. Tap Mode.
  • Page 57 Select arm mode in every tab. in every area to add it into arm mode. Multiple areas can be added into one arm mode simultaneously, whereas one area can be added into different modes. Forward Setting Forward incoming calls. Parameters at this interface are set on main VTH only, and extension VTH synchronizes with main VTH.
  • Page 58 Parameter Description All incoming calls will be forwarded to preset number Always immediately. When the user is busy, incoming call from the third party will be forwarded to preset number. If No Answer is not set, when Busy the user refuses to answer, the incoming call will be deemed as busy forwarding.
  • Page 59 Set time parameter. Turn on NTP, the VTH will syncronize time with the NTP server automatically; turn it off to set time or time zone manually. Set DND period Turn on DND period, set start and end time or click Click to select week to select the day(s), and you will not receive any call or message during this period.
  • Page 60 Default login password is 123456. Please refer to 0 Password Setting for details. Select General > Display. Display Set parameters. ; set Brightness and Screensaver Time. Tap Clean and the screen will be locked for 30 seconds. During the period, clean the screen. It restores after 10 seconds.
  • Page 61 Enter New Password and Confirm Password. Tap OK to complete password modification. QR Code Download the app on your smartphone by scanning the QR code, register the VTH on the app, and then you can unlock the door, or talk to the VTH, and more directly on your smartphone. Tap Setting.
  • Page 62 Scan the QR code on the right to download the DSS Agile VDP on your smartphone. Scan the QR code on the left to register the VTH to the app. For detailed operations of the app, see "0 DSS Agile VDP". Other Settings Set monitor time, record time, VTO message time, VTO talk time, resident-to-resident call enable, resident-to-resident call time, auto capture and touch ring.
  • Page 63 Paramet Description Monitor Maximum time to monitor VTO, IPC and fence Time station. Maximum recording time of videos during call, talk, Record monitoring and speaking. The system stops Time recording at the end of recording time. When VTO Message Time(s) is not 0: If the VTH has an SD card and does not answer the VTO, it will enter message status according to prompt, and save the message in the SD card.
  • Page 64 Paramet Description Touch After enabling touch ring, there will be a ring when Ring touching the screen. Product Info Reboot the system and format SD card. If SD card isn’t inserted into the device, SD format function is invalid. Tap Setting. Input login password and tap OK.
  • Page 65 Restart: Restart the device. Language: Change the language of the device. Format SD Card: Clear all data in the SD card. Be careful with this operation. Eject SD card: Eject the SD card first to safely remove it. Project Settings Forget Password If you forget initialization password when entering project settings interface, reset password through Forget Password at the interface or in VDPconfig tool.
  • Page 66 Scan the QR code with any code-scanning APP, bind your email box, send it by email to support_gpwd@htmicrochip.com, and thus obtain security code. Tap Next. Enter Password, Confirm Password and obtained Security Code. Tap OK to complete resetting the password. Reset the Password in VDPconfig VDPconfig tool to export XML...
  • Page 67 The device restarts and proceeds to initialization. Reset MSG Modify the bonded Email. Tap Setting for over 6 seconds. Enter the password set during initialization, and tap OK. Tap Reset MSG. Reset MSG Enter a new email address, turn on Reset Pwd, and then tap OK. The email will obtain security code during password resetting.
  • Page 68 Select arm mode. Enter arm and disarm password; tap OK. The device beeps continuously, which represents successful arm. The key displays corresponding arm mode. Default password of arm and disarm is 123456. Please refer to 0 Password Setting for details. If delay alarm is set in the area, the device will beep continuously at the end of exit delay time.
  • Page 69 DSS Agile VDP You can download DSS Agile VDP (hereinafter referred to as the "app") and link your VTH to the app to unlock the door, talk to connected VTO devices, call the management center, and view call records and messages. Interfaces and operations might vary between iOS and Android OS.
  • Page 70 Registration and Login on your smartphone, read the Software license agreement and Privacy policy, and then tap Agree (only for first-time login). Registration interface , and then scan the Register code on the VTH. See 0 in "0 Downloading the App". Confirm IP address and port number...
  • Page 71 Verify the IP address and port number, and then tap Confirm. Enter the username and password, and then tap Registration. You can add 5 users to one VTH at most. Login Tap the Login tab, enter the username and password you have set, and then tap Login. Call Functions You can receive the forwarded calls, remotely unlock the door, view live video of the VTO, and more.
  • Page 72 To receive push notifications of call messages on the mobile phone, make sure that notifications of the app are enabled on your smartphone, and you are logged in to the app. Forwarding Calls Confirm your SIP ID, and then configure call forwarding on the VTH. If any device calls the VTH, you will receive the call on your smartphone.
  • Page 73 Enter the password you configured, and then tap Forward. Forward Select forwarding type as needed: Always: All calls to this VTH will be forwarded. Busy: If the VTH is busy, the call will be forwarded. No Answer: Any call that is not answered within the defined ring time will be forwarded. See "0 Other Ring Settings"...
  • Page 74 to enable the forwarding type you selected, and then tap OK. Calling Operations After call forwarding is configured, you can receive and answer phone calls from the VTO or the management center. For example, when a VTO is calling, you can answer the call, view live video, and remotely unlock the door if the VTO is connected to a lock.
  • Page 75 , select the VTO from the channel list as needed. Live video...
  • Page 76 : Switch to another VTO. : Unlock the door remotely. : Have a two-way audio talk with the VTO. : Call management center. Call Records View the incoming and outgoing call records. Log in to the APP, and then tap Records. Call records...
  • Page 77 Red phone icon: The call is missed or not answered. Green phone icon: The call is answered. Not Opened/Opened: Indicates whether the door is unlocked. Edit: Delete the record one by one, or tap Edit > Empty to delete all records.
  • Page 78 Message You can view the unlocking records and alarm messages, and search for history messages. You need to enable Event Subscription in Setting of the App first. See "0 Setting" for details. To receive messages on your smartphone, make sure that notifications of the app are enabled on your smartphone and the you are logged in to the app.
  • Page 79 Searching for History Messages Tap History, set the start and end time, and then tap SEARCH. You search for messages within up to 7 days. History messages...
  • Page 81 Visitor You can create a pass for a visitor to have access permission. The pass is invalid after it is manually invalidated, the visiting period expires, or the visit is ended. You can also view visit records. Creating Pass Log in to the APP, and then tap Visitor. Visitor information Enter the information of the visitor, and then tap Generate Pass.
  • Page 82 Tap Send to Visitor to send the QR code to the visitor. Tap Save to save the QR code to your smartphone. (Optional) Tap Invalidate to cancel the appointment, and then the QR code will not have access permissions. Tap Invite Again to generate a new pass for the visitor. Invalidate the pass...
  • Page 83 Visit Records You can view visitor status such as having an appointment, on a visit, ending the visit, and cancelling the appointment. You can also view and modify the pass. View visitor status: Log in to the APP, tap Visitor > Record. View and modify a pass: Tap a visitor in the list, and then you can view detailed information of the pass, invalidate the appointment, invite the visitor again, and more.
  • Page 84 Setting You can view SIP ID, and enable message subscription, stream encryption, message sound, login by pattern, and more. Log in to the app, and then tap Setting. Setting...
  • Page 85 Event Subscription: Enable it, and then you can receive unlocking messages and alarm messages. See "0 Message" for details. Stream Encryption: Enable it to enhance security, but stream acquisition speed might slow down. Gesture: Draw a pattern, and then you can log in by that pattern. About: View app version, software license and privacy policy, help document, or log out of the current account.
  • Page 86 Thanks for Choosing CP Plus! Website: - www.cpplusworld.comEmail id: - sales@cpplusworld.com; support@cpplusworld.com...