NuWave ON-THE-GO, 28401 - Portable Blender Manual

NuWave ON-THE-GO, 28401 - Portable Blender Manual

Advertisement

NuWave ON-THE-GO, 28401 - Portable Blender Manual

IMPORTANT SAFEGUARDS

HOUSEHOLD USE ONLY
READ ALL INSTRUCTIONS BEFORE USE

Operating safety precautions

The following items are all designed to ensure the safe operation of the equipment, and to avoid accidents and undue losses. Please strictly abide by them. Use only with Listed/Certified ITE Power Supply.


Possibility of serious personal injury or death due to misuse.

  1. This blender is intended for household use only.
  2. This blender should be used on a safe, stable surface.
  3. If there are abnormal sounds, smells, or smoke during use, turn the blender off immediately and contact Customer Service.
  4. Before using, ensure that the USB-C cable is in good condition, and replace it at the first sign of damage. Contact Customer Service.
  5. Use the USB-C cable provided only as intended.
  6. Always handle the blender with care to avoid any damage.
  7. Avoid water leakage as it could cause external damage.
  8. Do not plug-in or unplug the USB-C cable with wet hands or towels.
  9. Plug-in the USB-C cable properly to avoid personal injury.
  10. Do not use the blender when there are gasoline fumes or natural gas in the air. Use in a ventilated area.
  11. Do not immerse the Power Base in any liquid. Use a warm wet towel to clean the inside, the blades, and exterior.
  12. To help avoid risk of thermal injury due to excessive pressure build-up in the container during use, do not blend hot liquids.
  13. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they are closely supervised and instructed concerning the use of the appliance by a person responsible for their safety. Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance.
  14. Avoid contact with any moving parts. Do not attempt to defeat any safety interlock mechanisms.
  15. Do not operate this, or any, appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Contact the manufacturer at their customer service telephone number for information on examination, repair, or adjustment.
  16. The use of attachments, including canning jars, is not recommended by the manufacturer as such use may cause a risk of injury to persons.
  17. Do not let the cord hang over the edge of any table or counter.
  18. Keep hands and utensils out of the container while blending to reduce the risk of severe injury to persons or damage to the blender. A scraper may be used, but only when the blender is not running.
  19. Do not use an extension cord. Plug the charger directly into an electric outlet.
  20. Only use with the charger provided with the appliance. Do not attempt to use this charger with any other product. Likewise, do not attempt to charge this appliance with any other charger.
  21. Do not incinerate this appliance even if it is severely damaged. The batteries can explode in a fire.
  22. This appliance is intended to be supplied by a Universal Serial Bus (USB).
  23. Choose the proper USB supply connection and do not use unapproved sources.

ADDITIONAL SAFEGUARDS


DO NOT attempt to use while charging.

  1. Please ensure that the Power Base is screwed onto the Jar properly to prevent injury and leakage.
  2. Do not overtighten the Jar to the Power Base.
  3. Make sure the USB cover on the Power Base is closed before use to prevent leakage.
  4. The blades are very sharp, use extreme caution.
  5. Before each use, please check that the sealing rings in the Power Base, the Lid, and Strainer are intact and completely installed.
  6. Do not put any accessories like the Jar, etc. in a microwave oven.
  7. Do not put your hands or other tools close to the blades while in use.
  8. Do not blend liquids over 120˚F/49˚C as this can damage the blender and cause leaks.
  9. Do not run without ingredients in the Jar, this could burn out the motor.
  10. Release any pressure before pouring blended ingredients.
  11. Sugars from mixed ingredients will start to ferment over time, which creates pressure inside a container. Avoid storing blends for long periods of time.
  12. This product is not a shaved ice machine. To make a delicious cold drink, it is recommended that you use frozen fruits and refrigerated beverages, or you can add crushed ice that accounts for 10% of the total capacity of the Jar and use water or other liquids to add 80% of the volume. Do not blend ice cubes or other hard objects without adding water or liquids, as this may damage the blades. Check the blades before each use.
  13. ALWAYS wait until the blending cycle has completed before detaching the Jar from the Power Base.
  14. The idling time of this product is about 5 seconds after starting up, and the longest blending time is 30 seconds. It needs to be fully cooled before being used again.
  15. For best results, your liquid and fruit mix should fill more than 20% of the Jar.
  16. This product contains a battery. When not in use, it should be stored in a clean, dry, ventilated room with an ambient temperature range of -23°F to + 95°F and a relative humidity of 25 to 75%.
  17. When not in use, store the Jar on the main unit.

PARTS & ACCESSORIES

PARTS & ACCESSORIES

Before Use

Check to see that all the accessories are included and not damaged.

Wash the accessories prior to use. Wipe down the Power Base with a wet towel. Never pour water directly over the Power Base or wash it in the dishwasher.

The blender comes partially charged. Fully charge the blender using the USB-C cable. You can connect the cable to any mobile phone power bank or mobile power bank as long the other end has a USB-A input.
Before Use

The blender will light up red while it charges, it will turn blue once it is fully charged. The normal charge time is 4 to 5 hours.

Operations

After being fully charged, the blender will operate for up to 30 minutes or approximately 60 cycles before it needs to be charged again.

Notes

  • 1 cycle is 30 seconds with 2 minutes of wait time before the next cycle.
  • When the Jar is not attached, the blender flashes red-blue-red-blue.

Blending

Blending - Step 1

  1. Be sure the Jar is properly attached to the Power Base.
  2. Before blending, cut all solid foods into small chunks.
  3. First, add your liquid(s) to the Jar.
  4. Add your solids and/or ice.
  5. Once all ingredients have been added, secure the Strainer on the Jar, then the Lid.
  6. Press the Power button twice to begin blending.

Note
Blending with the Strainer is optional. Use the Strainer if you wish to filter out chucky pieces.

Tip: If the blades become jammed, turn off the blender. Turn the blender horizontally and gently shake. If the blades are still jammed, turn the blender upside down and gently shake.
Blending - Step 2

Strainer
Filters out any chunky pieces.

Hot Liquids

Do not add liquids over 120˚F/49˚C as this can damage the blender and cause leaks.

Note

  • ALWAYS make sure all parts are attached and secure.
  • Do not overload the blender with ingredients. ALWAYS leave room at the top.
  • Do not run the blender with an empty Jar. This could burn out the motor.


Never attempt to touch the blades with your fingers.

Safety Features
The blender is equipped with a safety sensor that prevents the blades from spinning when the jar is detached.

CLEANING & MAINTENANCE

Fast Cleaning
Add warm soapy water to the Jar, press the Power button two times and rinse.

Note
For deep cleaning, remove the Lid and Strainer, as well as the attached silicone rings. Wash them with warm, soapy water using a brush, sponge or wet towel. Allow to dry. Do not pour water onto the Power Base. Use a wet towel to clean.

Specifications

Model No: 28401
Voltage: DC7.4V
Power: 70W
USB Cable: Type-C
Charging Time: 4 - 5 hours

TROUBLESHOOTING GUIDE

The Jar is screwed into the Power Base, but machine does not work.
Make sure the cup is screwed on tightly enough.

The red light stays on during mixing.
Insufficient voltage. Fully charge the Power Base before use.

The red light flashes when the power is turned on, and the blades do not turn.

  1. The battery temperature in the Power Base is too hot. Power off the unit and let it cool before use.

Note
The above are common troubleshooting methods. For more information and assistance contact Customer Service at 1-877-689-2838 or email help@nuwavenow.com.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download NuWave ON-THE-GO, 28401 - Portable Blender Manual

Advertisement

Need help?

Need help?

Do you have a question about the ON-THE-GO and is the answer not in the manual?

Questions and answers

Table of Contents