Download Print this page
NuWave 28202 Quick Start Manual
Hide thumbs Also See for 28202:

Advertisement

Quick Links

Troubleshooting Guide
The Infinity
Blender was engineered with an automatic shut-off feature to prevent overheating during use. If the Infinity
cool itself down, an odor may be detected. Unplug the Infinity
process at speeds not recommended.
The Infinity
Blender is not turning on or working.
1. Plug may not be in the outlet. Plug in the Infinity
Blender into
an appropriate power source.
2. The Red Power Switch on right side of Base may not be on.
Check to see if the Power Switch is on.
The Infinity
Blender does not work when plugged in and
Power button and Power Switch are both ON.
Make sure the unit is plugged correctly, try another wall power
outlet. If the problem persists, contact customer service.
The Infinity
Blender is not running at a high enough speed
for the recipe.
1. The Dial is not on the correct setting. Turn the Dial to proper
setting based on the recipe.
2. The Jar is overloaded. Reduce the amount of your
ingredients.
The Infinity
Blender becoming clogged and not operating
efficiently.
1. Certain ingredients can cause clogging. When using the
Plunger Lid, remove the Plunger Cap from the Lid and insert
the Plunger through hole. Press the ingredients down and
around until mixture loosens around the bottom of the Jar.
2. The ingredient amounts higher than specified are being used.
Do not fill the Jar above ¾ capacity (1.5 liters, 51 fl oz).
3. Large pieces of ice are not mixing properly. Use smaller pieces
of ice.
©2021 NuWave LLC • All Rights Reserved. • Customer Service: 1-877-689-2838• help@nuwavenow.com
Model No: 20902 • Item No: BQ20902 • Rev. 2-OG • 12-16-21
Blender and wait for it to completely cool down. To prevent overheating, do not
The blended mixture has lumps or the texture is not even.
Air pocket has formed (cavitation) and mixture is too cold or has
solidified in areas, and the blades are spinning in cavity. Increase
the temperature by reducing ice in the recipe.
Noises or motions unusual for the normal operation of the Infinity
Blender are detected.
1.
The Blade assembly may be loose, missing a part, or possibly
damaged. Turn the Infinity
Blender OFF and unplug immediately.
DO NOT disassemble the Blade assembly. Call Customer Service:
1-877-689-2838 or email help@nuwavenow.com.
2.
Foreign objects from ingredients may have been put into the Jar and
are making unusual sounds. Prior to adding your ingredients to the
Jar and blending, clean fruits/other ingredients and remove all debris
or any objects.
Error Message:
Solution(s)
The NTC Temperature Sensor has short circuited.
Contact NuWave Customer Service 1-877-689-2838
Er1
or help@nuwavenow.com.
The NTC Temperature Sensor is open. Contact
Er2
NuWave Customer Service 1-877-689-2838
or help@nuwavenow.com.
The NTC Sensor has overheated. Turn the Infinity
Blender off and allow it to cool. If the Infinity
Er3
Blender is not working after it cools down, Contact
NuWave Customer Service 1-877-689-2838 or
help@nuwavenow.com.
Blender shuts off to
I N F I N I T Y B L E N D E R
Model No: 28202
Getting Started
Button
Function
Turns the Infinity
Starts and pauses the cooking process,
Start/Pause
and allows you to clear any selections.
Set your time. Press the up and down
Time
arrows to increase or decrease the time on
the display.
Number
Use the numbered settings. Default time is
Settings
3 minutes
Icon settings are for specialized blending
Icons
tasks. Each icon setting has default time
and RPM built in.
The Infinity
Pulse
functions where the power settings are fully
adjustable.
Cleaning
For quick cleaning with soap and water.
TM
Use
Turn the red main Base Power Switch ON. Switch is located on the right side of Blender Base.
Press Power button once to turn your Infinity
Blender on and off.
press the red main Base Power Switch OFF to turn your Infinity Blender
Turn the dial to choose your appropriate blending function. Press Start/Pause to start
blending. Press Start/Pause again to stop blending. Note: Do not fill Jar above ¾ capacity.
For best results, do not fill more than 1.5 liters (51 fl oz) of liquid. Refer to "Instructions" in
the owner's manual.
Times are displayed in minutes and seconds. Adjustments can be made on all settings. Note:
When blending for a long period of time, liquids may become hot and steam may escape from
the Plunger Cap.
For standard blending you can select from one of the numbered speed settings between 1 and
10. Adjust to desired time, then press Start/Pause to begin blending. Note: The lowest setting
is #1 (5,000 RPM). The highest setting is #10 (17,000 RPM).
Turn the dial to desired icon setting and press Start/Pause to begin blending. Note: Always
start with cold liquids when blending. DO NOT add hot liquids to the Infinity
Up and Down buttons to move percentage points faster.
Blender offers two Pulse
Press Pulse 1 for short bursts of blending at low power (25% Power).Press Pulse 2 for short
bursts of blending at high power (100% Power).
Add water and 1-2 drops of liquid dish soap to your Jar, place on the Base, and close the
Lid. Turn the dial to Clean. 00:15 will be shown on the LED display. Adjust the time if desired,
and then press Start/Pause. Once finished, remove the Jar, rinse thoroughly, and dry before
using. Note: For detailed instructions on cleaning refer to "Cleaning & Maintenance."
Quick Start Guide
Refer to the Owner's Manual for more details
Blender on. Press the Power button again and
off.
Blender. Hold the

Advertisement

loading
Need help?

Need help?

Do you have a question about the 28202 and is the answer not in the manual?

Questions and answers

Summary of Contents for NuWave 28202

  • Page 1 Start/Pause. Once finished, remove the Jar, rinse thoroughly, and dry before using. Note: For detailed instructions on cleaning refer to “Cleaning & Maintenance.” ©2021 NuWave LLC • All Rights Reserved. • Customer Service: 1-877-689-2838• help@nuwavenow.com Model No: 20902 • Item No: BQ20902 • Rev. 2-OG • 12-16-21...
  • Page 2 Icon Settings 1-10 Settings For more specialized blending tasks you can select one of the preset icons with the dial. Each icon setting has a default time and RPM built For standard blending you can select your blending speed from one of the numbered settings from 1 to 10. Turn the dial to your desired settings from 1 to 10.