Subscribe to Our Youtube Channel
Related Manuals for Elsner 70122
Summary of Contents for Elsner 70122
- Page 1 KNX W Wind Sensor KNX W 20...30 V DC No. 70123 KNX W 230 V AC No. 70122 Installation and Adjustment...
-
Page 3: Table Of Contents
7.4.2. OR Logic 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 ..............21 7.4.3. Linkage inputs of OR Logic ................ 21 Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany Wind Sensor KNX W • from software version 1.00, ETS programme version 1.1... - Page 4 The change status (software version and date) can be found in the contents footer. If you have a device with a later software version, please check www.elsner-elektronik.de in the menu area "Service" to find out whether a more up-to- date version of the manual is available.
-
Page 5: Description
The output of each gate may optionally be configured as 1 bit or 2 x 8 bits Configuration is made using the KNX software ETS. The product file can be down- loaded from the Elsner Elektronik website on www.elsner-elektronik.de in the “Ser- vice” menu. 1.1. Deliverables •... -
Page 6: Installation And Commissioning
Installation and commissioning Current 230 V AC version max. 20 mA. 20...30 V DC version: max. 30 mA., max. 0,4 W. Residual ripple 10% Data output KNX +/- bus terminal plug Group addresses max. 254 Allocations max. 255 Communication objects Measurement range Wind 0...35 m/s Resolution (wind) -
Page 7: Location
Elsner Elektronik is not liable for any changes in norms and standards which may occur after publication of these operating instructions. 2.1. Location Select an assembly location at the building where wind speed may be collected by the sensor unobstructedly. -
Page 8: Mounting The Sensor
Installation and commissioning Fig. 3 Horizontal The wind sensor must be mounted in the horizontal transverse direction (horizontally). 2.2. Mounting the sensor 2.2.1. Attaching the mount The sensor comes with a combination wall/pole mount. The mount comes adhered by adhesive strips to the rear side of the housing. Fasten the mount vertically onto the wall or pole. -
Page 9: View Of Rear Side And Drill Hole Plan
Installation and commissioning Fig. 6 Different mounting arms are available from Els- ner Elektronik as additional, optional accessories for flexible installation of the weather station on a wall, pole or beam. Example of the use of a mounting arm: Due to flexible ball joints, the sensor can be brought into ideal position. -
Page 10: Preparing The Sensor
Installation and commissioning 2.2.3. Preparing the sensor Unsnap cover and remove upwards Fig. 9 Screw-on cover (230V device) Cover Snaps Bottom part of housing The sensor cover snaps in on the left and right along the bottom edge (see Fig.). The cover of the 230V model is also screwed on top. -
Page 11: Pcb Layout
Installation and commissioning Lead the cable for the voltage supply and bus connection through the rubber seals on the bottom of the device and connect Voltage L/N and Bus +/- to the terminals provid- Fig. 10 Remove the cable shielding under the circuit board and only feed the connector cables up- wards through the openings in the circuit board. -
Page 12: Mounting The Weather Station
Installation and commissioning 20...30 V DC version Fig. 12 Tension clamp for voltage supply (20...30 V DC). Massive conductors of up to 1.5 mm² or conductors with fine wires. Terminal configu- ration independent from po- larity (+/- or -/+). Opening for the cable for the voltage supply and for bus ca- Slot for KNX clamp +/- Programming pushbutton for... -
Page 13: Notes On Mounting And Commissioning
Installation and commissioning Fig. 14 With the 230V model, screw the cover on to the underpart, to prevent unauthorised or ac- cidental opening. DANGER! There is a risk to life from the live voltage on a 230 V device! • The cover must be screwed on in operation. -
Page 14: Addressing Of The Device At The Bus
Addressing of the device at the bus The measured wind value and thus all other wind switching outputs may only be sup- plied 60 seconds after the supply voltage has been connected. After the auxiliary voltage has been applied, the device will enter an initialisation phase lasting a few seconds. - Page 15 Disposal Wind Sensor KNX W • Status: 11.11.2021 • Technical changes reserved. Errors reserved.
-
Page 16: Transmission Protocol
Transmission protocol 6. Transmission protocol Units of measurement: Wind in metre per second 6.1. List of all communication objects EIS types: Switching 1/0 Floating point value 8 bit value Abbreviations Flags: Communication Read W Write Transmit Name Function EIStype Flags Wind force measured value Output C R T... - Page 17 Transmission protocol Name Function EIStype Flags Wind threshold value 3 Increment C R W Wind threshold value3 Decrement C R W Wind threshold value 3 Switching output C R T Wind threshold value 3 Switching output C R W block AND Logic 1 Switching output C R T...
- Page 18 Transmission protocol Name Function EIStype Flags OR Logic 4 8 bit output B C R T OR Logic 5 Switching output C R T OR Logic 5 8 bit output A C R T OR Logic 5 8 bit output B C R T OR Logic 6 Switching output...
-
Page 19: Setting Of Parameters
Setting of parameters 7. Setting of parameters 7.1. General settings Maximum telegram quota 1 • 2 • 3 • 5 • 10 • 20 telegrams per second Wind force Measured value • do not send • send periodically • send in case of change •... - Page 20 Setting of parameters If the threshold value is set per Communication object: From the 1st communication onwards, the threshold value corresponds to the value of the communication object and is not multiplied by the factor 0.1. The value communicated last shall be •...
-
Page 21: Logic
Setting of parameters If block of the switching output is used: Use block of the switching output Evaluation of the blocking object • if value 1: block | if value 0: release • if value 0: block | if value 1: release Value of the blocking object before 0 •... -
Page 22: Linkage Inputs Of And Logic
Setting of parameters Communication object • in case of the change of logic AND Logic 1 sends • in case of the change of logic to 1 • in case of the change of logic to 0 • in case of the change of logic and cyclically •... -
Page 23: Or Logic 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8
Setting of parameters Communication object logic input 8 Communication object logic input 8 inverted Malfunction wind Malfunction wind inverted Wind threshold value 1 Wind threshold value 1 inverted Wind threshold value 2 Wind threshold value 2 inverted Wind threshold value 3 Wind threshold value 3 inverted 7.4.2. - Page 24 Elsner Elektronik GmbH Control and Automation Engineering Sohlengrund 16 75395 Ostelsheim Phone +49 (0) 70 33 / 30 945-0 info@elsner-elektronik.de Germany +49 (0) 70 33 / 30 945-20 www.elsner-elektronik.de Technical support: +49 (0) 70 33 / 30 945-250...
Need help?
Do you have a question about the 70122 and is the answer not in the manual?
Questions and answers