Page 1
Operator Manual / Manual del operador Z 242F Zero Turn Mower / 967271801-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.
Page 2
CONFORMITY CERTIFICATES USA requirements Labels are placed on the engine and/or in the engine compartment stating that the machine will fulfill the requirements. This is also applicable to special requirements for any of the states, (California emission rules etc.). Do not remove these labels. Certificates can also be supplied with the machine at delivery or written in the Engine manual.
CONTENTS INTRODUCTION ............4 INTRODUCCIÓN ............. 39 Driving and Transport on Public Roads ....4 Conducción y transporte en vías públicas ..39 Towing ..............4 Remolque ............39 Operating ............. 4 Funcionamiento ..........39 SYMBOLS AND DECALS .......... 6 SÍMBOLOS Y RÓTULOS .........
INTRODUCTION Congratulations Towing Thank you for purchasing a Husqvarna ride- If machine is equipped with a tow hitch, use much on mower. This machine is built for superior more caution when towing. Do not let children or efficiency to rapidly mow primarily large areas.
Page 5
INTRODUCTION Good Service Husqvarna's products are sold throughout the world and only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by the retailer.
reader neglects to follow the instructions in the SYMBOLS AND DECALS manual. These symbols are found on the machine and in the operator manual. IMPORTANT INFORMATION Xxxx xxxxxx Study them carefully so that you know what they xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. mean.
• Do not let children to operate the machine. SAFETY • Use extreme care when going near blind Safety Instructions corners, shrubs, trees, or other objects that may These instructions are for your safety. Read them block your view of a child. carefully.
Personal Safety Equipment SAFETY • Make sure that first • Always turn off blades, move the steering aid equipment is control lever out to the park brake position, stop close at hand when engine and remove keys before dismounting. using the machine. •...
open device. SAFETY • If fuel is spilled on clothing, change clothing foot on the ground. immediately. • Do not mow near drop-offs, ditches, or • Do not start the engine near spilled fuel. embankments. The machine could suddenly • Do not use gasoline as a cleaning agent. roll over if a wheel is over the edge or the edge •...
Transport SAFETY • The machine is • Stop to inspect the equipment if you run over or heavy and can into anything. If necessary, make repairs before cause serious starting. crushing injuries. • Do not make adjustments or repairs with the Be extra cautious engine running.
A spark arrestor for the muffler is available Follow the manufacturer’s recommendation for through an authorized Husqvarna dealer. weight limits for towed equipment. Do not tow near ditches, canals, and other hazards.
CONTROLS This operator manual describes the Husqvarna belt-driven hydraulic pumps. Using the left and Zero Turn Rider. The rider is fitted with a four- right steering controls, the flow is regulated and stroke overhead valve engine. thereby the direction and speed.
CONTROLS WARNING! The machine can turn very Steering Control Levers rapidly if one steering control is moved much further forward than the other. Park Brake The machine’s speed and direction are continuously variable using the two steering controls. The steering controls can be moved The park brake is integrated with the steering forward or backward about a neutral position.
Service Meter CONTROLS Throttle Control The service meter displays the total operating time with the blade activated. The throttle control regulates the engine speed At 50 hour intervals of operation, an oil can and thereby the rate of rotation of the blades, icon shows and stays on for two hours before assuming the blade switch is pulled out.
Cutting Height Lever CONTROLS Fuse To set the deck cutting height, pull the cutting height lever inwards and move it to the desired The 20 amp primary fuse is located on the left height notch. hand side of the machine. It is accessed by tilting the seat forward.
CONTROLS IMPORTANT INFORMATION Experience indicates that alcohol blended fuels (called Fuel Tank gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.
To turn to the left OPERATION While moving in a forward direction pull the left Read the Safety section and following pages if lever back towards the neutral position while you are unfamiliar with the machine. maintaining the position of the right lever, this will slow the rotation of the left wheel and cause the Training machine to turn in that direction.
Page 18
Running OPERATION 1. Release the park brake by pulling the steering 3. Disengage the mower blades by pressing the / park brake controls inwards to the neutral blade switch downwards. position at the same time. NOTE: The mower is equipped with an operator presence system.
Mowing Tips OPERATION • Observe and flag rocks and other fixed objects to avoid collisions. IMPORTANT INFORMATION When stopping • Begin with a high cutting height and reduce it and leaving the machine, both steering / park until the desired mowing result is attained. The brake controls must be moved out to the locked average lawn must be cut to 2-1/2"...
OPERATION IMPORTANT INFORMATION To manually push the mower, engage the hydro bypass Moving Machine By Hand levers on both sides, pull both steering / park When pushing or pulling the mower, engage the brake controls inwards and push machine. EZT bypass linkages. The EZT bypass linkages are located on the rear of the frame, below the rear engine guard.
carried out by an authorized service workshop MAINTENANCE is recommended to maintain the machine in the Maintenance Schedule best possible condition and to make sure of safe operation. Following is a list of maintenance procedures that must be performed on the machine. For Read General Maintenance in the Safety those points not described in this manual, visit an section.
Page 22
MAINTENANCE MAINTENANCE INTERVAL AT LEAST DAILY IN HOURS ONCE EACH BEFORE AFTER MAINTENANCE YEAR CHECK ■ Throttle cable for adjustment ● ● Mower deck for adjustment ● ● Condition of belts, belt pulleys ● ● Caster wheels (at 200 hour intervals) ♦...
MAINTENANCE STATE APPROXIMATE CHARGING TIME* TO FULL CHARGE AT 80 BATTERY Battery Maximum Rate at: CHARGE If the battery is too weak to start the engine, it 50 Amps 30 Amps 20 Amps 10 Amps must be recharged. 12.6V 100% - FULL CHARGE - Jumper Cable Use 12.4V...
For any further adjust to the park brake, contact startup. the Husqvarna service workshop. NOTE: If the steering / park brake controls not holding in the full outboard position, the...
6. Push inward on the idler arm to release the MAINTENANCE tension on the belt. Caster Wheels 7. Slip the belt over the top of the cutter housing pulleys and remove the belt from the deck. Check at 200 hour intervals. Check that wheels turn freely.
Adjust IMPORTANT INFORMATION Special blade the nut until rear blade tip is 1/4" to 3/8" bolt is heat treated. Replace with a Husqvarna higher than the front blade tip. bolt if required. Do not use lower grade NOTE: This will position the mower deck in a hardware than specified.
MAINTENANCE Cleaning Regular cleaning, especially under the mower deck, will increase the machine’s life-span. Clean the machine directly after use (after it is cooled), before the debris sticks. Do not spray water on the top of the mower deck. Use compressed air to clean the top side of the mower deck.
LUBRICATION 12/12 Each year Lubricate with grease gun 1/52 Each Week Filter change 1/365 Each day Oil change Level check General Remove the ignition key to prevent unintentional Clean away unwanted grease after lubrication. movements during lubrication. It is important to avoid getting lubricant on the When lubricating with an oil can, it must be filled belts or the drive surfaces of the belt pulleys.
The transmission is maintenance free. It is not recommendations. necessary to do level checks or oil changes. If a leak occurs, replace the unit or contact any Husqvarna dealer. WARNING! The engine drain plug is located close to the muffler. To prevent burns, Wheel and Deck Zerks the engine should be shut off and allowed to Use only good quality bearing grease.
TROUBLESHOOTING Problem / Cause Engine will not start Engine overheats Blade switch is engaged Clogged air intake or cooling fins Steering controls are not locked in the outer Engine overloaded position Inadequate ventilation around engine Dead battery Defective engine speed regulator Contamination in the carburetor or fuel line Too little or no oil in the engine Fuel supply shutoff valve is closed or in the...
Drain the fuel purchase year, model, type, and serial number. into an approved container outdoors and Always use genuine Husqvarna spare parts. store far away from open flame or sources of An annual check-up at an authorized service ignition.
TECHNICAL DATA ENGINE Manufacturer Kawasaki Type FX651V Power 21.5 hp Lubrication Pressure with oil filter Fuel Min 87 octane unleaded (Max ethanol 10%, Max MTBE 15%) Fuel tank capacity 3-1/2 gallons (13.25 litres0 Cooling Air cooled Air filter Standard Alternator Starter Electric TRANSMISSION...
Page 34
TECHNICAL DATA Torque Specifications Standard 1/4" fasteners 9 ft/lb Engine crankshaft bolt 50 ft/lb Standard 5/16" fasteners 18 ft/lb Deck pulley bolts 150 ft/lb Standard 3/8" fasteners 33 ft/lb Lug nuts 75 ft/lb Standard 7/16" fasteners 52 ft/lb Blade bolt 90 ft/lb Standard 1/2"...
SERVICE JOURNAL DELIVERY SERVICE Action Date, mtr reading, stamp, sign Charge and connect the battery Adjust the tire pressure of all wheels to 15 PSI (1 bar) Connect the contact box to the cable for the seat’s safety switch Check that the right quantity of oil is in the engine Adjust the position of the steering controls Fill with fuel and open the fuel shut off valve Start the engine...
Page 36
SERVICE JOURNAL AFTER 10 HOURS Action Date, mtr reading, stamp, sign Change the engine oil DAILY SERVICE Action Date, mtr reading, stamp, sign Clean debris from mower Check engine oil level Check the tire pressures Check underside of deck Check safety system Check fuel system for leaks Inspect safety guards and shields Check brake adjustment...
Page 37
SERVICE JOURNAL 100-HOUR SERVICE Action Date, mtr reading, stamp, sign Do the 25-hour service Do the 50-hour service Change the engine oil filter Clean/replace the spark plugs Replace the fuel filter Check V-belts Check / tighten caster wheel axle bolts (at 200 hour intervals) Change the air filter’s paper cartridge 300-HOUR SERVICE Action...
Page 38
CERTIFICADOS DE CONFORMIDAD Requisitos para EE.UU. En el motor y/o en el compartimiento del motor hay etiquetas que indican que la máquina cumple con los requisitos. Esto también es aplicable a requisitos especiales para cualquiera de los estados, (normas de emisiones de California, etc.). No retire ninguna de estas etiquetas. También es posible que se incluyan certificados con la máquina en el momento de su entrega o que estén escritos en el manual del motor.
Si la máquina está equipada con un sistema de Felicitaciones remolque, extreme las precauciones al remolcar. Gracias por adquirir un cortacésped Husqvarna. No lleve a niños ni otras personas dentro del Esta máquina se ha fabricado para lograr una equipo remolcado o sobre él. Realice giros eficiencia superior al cortar con rapidez áreas...
Page 40
INTRODUCTION Buen servicio Los productos Husqvarna se venden en todo el mundo y solo en tiendas minoristas especializadas con servicio completo. Esto asegura que como cliente, usted reciba solo el mejor nivel de asistencia y servicio. Antes de la entrega del producto, el distribuidor ha sometido la máquina, por ejemplo, a inspecciones y...
lector no sigue las instrucciones proporcionadas SÍMBOLOS Y RÓTULOS en el manual. Estos símbolos se encuentran en la máquina y en el manual del operador. IMPORTANT INFORMATION Xxxx xxxxxx Estúdielos atentamente para que sepa qué xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. significan.
• No permita que los niños operen la máquina. SEGURIDAD • Tenga cuidado extremo al acercarse a curvas Instrucciones de seguridad sin visibilidad, arbustos, árboles u otros objetos Estas instrucciones son para su propia seguridad. que puedan bloquear su visión e impedir que Léalas atentamente.
• Siga las recomendaciones del fabricante para SEGURIDAD los pesos de las ruedas o los contrapesos. • No maneje la máquina si no tiene el recogedor • Mantenga la máquina libre de cualquier de césped completo, la protección de descarga acumulación de césped, hojas u otra basura, u otros dispositivos de seguridad en su lugar y pues podrían entrar en contacto con el escape...
• No llene la máquina SEGURIDAD de combustible en • No corte el césped húmedo. Los neumáticos interiores. podrían perder tracción. • No almacene • Evite arrancar, parar o girar en una pendiente. la máquina o Si los neumáticos el recipiente de pierden tracción, combustible donde desacople las...
Page 45
• Pueden producirse chispas cuando se trabaja SEGURIDAD con la batería y los cables pesados del circuito del motor de arranque. Esto puede causar una de carbono, un gas inodoro, venenoso y letal. explosión de la batería, incendio o daños en •...
Se puede obtener un apagachispas para el silenciador a través de un distribuidor de Husqvarna autorizado. • No utilice esta máquina en vías públicas. • Consulte y respete las normas de tráfico locales antes de transportar la máquina en cualquier camino.
Este manual del operador corresponde al Utilizando los controles de la dirección izquierdo cortacésped Zero Turn de Husqvarna. El y derecho, el caudal regula el sentido de marcha cortacésped está equipado con un motor de y la velocidad.
CONTROLES Palancas de control de la dirección Hacia adelante Freno de Neutro estacionamiento Reversa ADVERTENCIA: La máquina puede girar La velocidad y la dirección de la máquina son de muy rápidamente si mueve un control de la tipo variable continua con los dos controles de la dirección mucho más que el otro.
manualmente el medidor, gire la llave a la CONTROLES posición de apagado cinco veces con intervalos Interruptor de encendido de un segundo. Para obtener información sobre el mantenimiento del motor y el cortacésped, consulte el Registro de servicio de este manual. Tenga en cuenta: El indicador de servicio funciona (horas de reloj) solo cuando el motor está...
Palanca de altura de corte CONTROLES Fusible Para ajustar la altura de corte del equipo, tire de la palanca de altura de corte hacia dentro y El fusible principal de 20 amperios está ubicado muévala a la muesca de la altura deseada. en el lado izquierdo de la máquina.
Desplazamiento CONTROLES Depósito de combustible Si el cortacésped no se mueve en línea recta, revise la presión de aire de los dos neumáticos Lea las instrucciones de seguridad antes de traseros. La presión de aire recomendada para cargar combustible. La máquina tiene un solo los neumáticos traseros es de 15 psi (1 bar).
Tire ligeramente hacia atrás las palancas de OPERACIÓN control para que el cortacésped se mueva hacia Lea la sección Seguridad y las páginas siguientes atrás. Empuje las palancas de control hacia si no está familiarizado con la máquina. delante, hasta la posición neutra y el cortacésped dejará...
Page 53
6. Presione y gire la llave de encendido a la OPERACIÓN posición de arranque. Arranque del motor INFORMACIÓN IMPORTANTE No haga 1. Siéntese en el asiento. funcionar el motor de arranque durante más 2. Levante el equipo de corte hasta la posición de cinco segundos cada vez.
Page 54
• El resultado del corte será mejor con un OPERACIÓN régimen del motor alto (cuando las cuchillas 4. Conecte el equipo de corte tirando el giran rápidamente) y a baja velocidad (el interruptor de cuchilla hacia arriba. cortacésped se mueve lentamente). Si el pasto no está...
OPERACIÓN Trabajo en pendientes Lea las instrucciones de seguridad de Conducción en pendientes en la sección Seguridad. • Se debe usar la velocidad más lenta posible antes de comenzar a bajar o subir colinas. • Evite detenerse o cambiar de velocidad en las colinas.
autorizado. Se recomienda enviar la máquina a MANTENIMIENTO revisión una vez al año en un taller de servicio Programa de mantenimiento autorizado para mantenerla en las mejores condiciones posibles y para garantizar un La siguiente es una lista de procedimientos funcionamiento seguro.
Page 57
MANTENIMIENTO INTERVALO DE DIARIO AL MENOS MANTENIMIENTO EN HORAS MANTENIMIENTO UNA VEZ AL ANTES DESPUÉS AÑO CHECK ■ Ajustar el cable del acelerador ● ● Ajustar el equipo de corte El estado de las correas, poleas de ● ● correa ●...
El cortacésped está equipado con una batería MANTENIMIENTO que no requiere mantenimiento. Sin embargo, Batería cargar periódicamente la batería con un cargador de batería automotriz prolongará su vida útil. Si la batería está demasiado baja como para • Mantenga la batería y las terminales limpias. arrancar el motor, se debe recargar.
Para realizar cualquier otro ajuste en el freno de pivote. (Consulte Freno de Estacionamiento en esta estacionamiento, póngase en contacto con el sección). taller de servicio de Husqvarna. INFORMACIÓN IMPORTANTE La máquina Realice inspecciones diarias para asegurarse de debe estar absolutamente detenida cuando se que el sistema de seguridad funcione intentando aplica el freno de estacionamiento.
tensora fija. Una vez que correa está MANTENIMIENTO correctamente instalada, suelte lentamente Correas en V del brazo guía para tensar la correa. Revíselas cada 100 horas de funcionamiento. 6. Revisar la ruta de la cinta para asegurarse de Revise si hay grietas profundas y mellas grandes. que coincida con la etiqueta sobre la ruta, y que la cinta no esté...
INFORMACIÓN IMPORTANTE El perno de la cuchilla especial está tratado con calor. Reemplácelo por un perno Husqvarna si es necesario. No utilice tornillería de grado inferior al especificado.
Limpieza MANTENIMIENTO La limpieza regular, especialmente por debajo Presión de los neumáticos del equipo de corte, aumenta la vida útil de la máquina. Limpiar la máquina directamente Todos los neumáticos deben tener una presión después de cada uso (una vez que se haya de 15 psi / 103 kPa / 1 bar.
Para el uso diario, la máquina debe lubricarse Si se produce una fuga, reemplace la unidad dos veces por semana. o póngase en contacto con su distribuidor Husqvarna. Limpie el exceso de grasa después de la lubricación. Es importante evitar que quede lubricante en las correas o las superficies de avance de las poleas de correa.
Engrasadores de rueda y equipo LUBRICACIÓN Utilice únicamente grasa para cojinetes de buena Cambio de aceite del motor calidad. La grasa de marcas reconocidas (empresas NOTA: Cambie el aceite del motor cuando petroquímicas, etc.) generalmente mantiene una el motor esté caliente. Consulte el manual buena calidad.
SOLUCIÓN DE PROBLEMAS Problema / Causa El motor se sobrecalienta El motor no arranca Obstrucción en la entrada de aire o las aletas de El interruptor de la cuchilla está activado refrigeración Los controles de dirección no están bloqueados Sobrecarga del motor en la posición externa Ventilación deficiente alrededor del motor La batería está...
Utilice siempre piezas de repuesto Husqvarna fuentes de ignición. No utilice gasolina para la originales. limpieza. Utilice un desengrasador y agua tibia.
DATOS TÉCNICOS MOTOR Fabricante Kawasaki Tipo FR651 Electricidad 21.5 hp Lubricación Presión con filtro de aceite Mínimo sin plomo de 87 octanos Combustible (máx. etanol al 10%, máx. MTBE al 15%) Capacidad del depósito de combustible 13,25 litros Refrigeración Refrigerado por aire Filtro de aire Estándar Alternador...
Page 69
DATOS TÉCNICOS Especificaciones de par Perno del cigüeñal del motor 75 pies/lb (102 Nm) Sujetadores estándar 1/4" 9 pies/lb (12 Nm) Tornillos de polea de corte 75 pies/lb (102 Nm) Sujetadores estándar 5/16" 18 pies/lb (25 Nm) Tuercas del asa 75 pies/lb (102 Nm) Sujetadores estándar 3/8"...
REGISTRO DE SERVICIO SERVICIO DE ENTREGA Fecha, Lectura De Medidor, Acción Sello, Firma Cargar y conecte la batería Ajustar la presión de los neumáticos de todas las ruedas a 15 psi (1 bar) Conectar la caja de contacto al cable para el interruptor de seguridad del asiento Verificar que el motor tenga la cantidad correcta de aceite Ajustar la posición de los controles de la dirección...
Page 71
REGISTRO DE SERVICIO DESPUÉS DE 10 HORAS Fecha, Lectura De Medidor, Acción Sello, Firma Cambiar el aceite del motor MANTENIMIENTO DIARIO Fecha, Lectura De Medidor, Acción Sello, Firma Limpiar los residuos del cortacésped Revisar el nivel del aceite del motor Comprobar la presión de los neumáticos Revisar la parte inferior del equipo Comprobar el sistema de seguridad...
Page 72
REGISTRO DE SERVICIO SERVICIO DE 100 HORAS Fecha, Lectura De Medidor, Acción Sello, Firma Realizar el mantenimiento después de 25 horas Realizar el mantenimiento después de 50 horas Change the engine oil filter Clean/replace the spark plugs Reemplazar el filtro de combustible Revisar las correas en V Comprobar/apretar los pernos de los ejes de las ruedecillas (cada 200 horas...
Page 73
REGISTRO DE SERVICIO SERVICIO DE 100 HORAS Fecha, Lectura De Medidor, Acción Sello, Firma...