Table of Contents
Advertisement
Quick Links
Warning:
Please be advised that the installation manual for your carport is
subject to change without notice. As such, we strongly urge you to use the most
recent version of the manual before attempting to install your carport. This is
important to ensure that you have the latest and most accurate instructions to
guide you through the installation process. The latest version of the manual can
always be found on our website at the following link:
https://www.blikir.com/resources
Document Version: 08G4/2023/V02/ENG
Released on: August 1st, 2023
© BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc.
Date: 08G4/2023/V02/ENG. Subject to change without notice
RCP-2 G4 |
Solar Carport / Canopy
1
Advertisement
Table of Contents
Summary of Contents for BLIKIR RCP-2 G4
- Page 1 Document Version: 08G4/2023/V02/ENG Released on: August 1st, 2023 © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice...
-
Page 2: Table Of Contents
2.5 Slide Connector Sleeves on Beams 2.6 Connect Middle Beams 2.6 Connect Beams at the center © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 3: Disclaimer
Photovoltaic Modules and Panels. NOTE: Always check with the Authority Having Jurisdiction (AHJ) for additional requirements © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 4: Introduction
2015 International Building Code 2018 International Building Code 2021 International Building Code ASCE 7-10 ASCE 7-16 © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 5: Maintenance
By performing these routine inspections and tightening, you help ensure the continued stability and safety of your structure. © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 6: Required Tools
Qty 48 x #4 Rebar 30” ● Non-Shrink Grunt ● Qty 16 x Wire Mesh, 10 Gage min., 6” grid © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 7: Main Components
J - Middle Connector K - Base Plate L - Escutcheon Plate (base plate cover) © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 8: Standard Dimensions
RCP-2 G4 | Solar Carport / Canopy Standard Dimensions © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 9: Pier Location Diagram
RCP-2 G4 | Solar Carport / Canopy © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 10: Components List
HIT-HY 200 Adhesive ● Qty 16 x Wire Mesh, 10 Gage min., 6” grid ● Non-Shrink Grunt © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 11: Ironridge Racking Components
2 X Safety Column Solar 2 X 3M VHB tape for safety lights LED Light (optional) © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 12: Build Base
Before you dig any holes, contact all utilities in the area to locate any underground lines, pipes, and wiring. © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 13: Reinforcing And Concrete
If you choose to follow option B that is described in section 1.5 and install the base anchors lower than the surface, pour the concrete up to the desired height under the surface. © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 14: Align Base Plates
The use of gravel is necessary to facilitate proper water drainage. © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 15: Build Structure
Once the installation is complete, tighten all the bolts (2) to level the beams (12, 13) effectively. © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 16: Connect Corners
© BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 17: Connect Beams To Corner Connectors
Finally, tighten the set screws you installed on the corner sleeves in step 2.2 until the beams are appropriately leveled. SIDE VIEW: TOP VIEW: © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 18: Slide Connector Sleeves On Beams
Finally, tighten the set screws you installed on the sleeves in step 2.2 until the beams are appropriately leveled. © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 19: Connect Beams At The Center
(3). Finally, tighten the set screws from step 2.2 until the beams are appropriately leveled. © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 20: Connect Rails
(3). Torque to 250 in-lbs (21 ft-lbs). Vertical side of L feet faces this way © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 21: Cut Rails To Match Panel Size
You can cut the rails in step 3.2 in a way that avoids this situation, in case your panel dimensions result in such an occurrence. © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 22: Connect Rails To L-Feet
Feet. Level the rail at the desired height, and then tighten to a torque of 250 in-lbs. © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 23: Connect Grounding Lug To Rail
If you are using MLPE (microinverters, RSD or optimizers), you can install them at this step © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 24: Install Solar Panels
Ensure CAMO bonding pins are fully seated on top of module frame. © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 25: Connect First Column Of Panels
• In case of re-installation requirements, it is recommended to use new jumpers. • It effectively supports bottom flange thicknesses ranging from 1.2mm to 3.1mm. © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 26: Optional Add Ons
Repeat these steps for the remaining two corners, ensuring a uniform and attractive appearance for your installation. © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 27: Optional: Ev Chargers
To continue with the installation process, please refer to the Enel X installation manual for detailed instructions and guidance. © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice... -
Page 28: Optional: Columns Safety Solar Led Lights
Please ensure to follow these instructions for optimal use and performance of the Column Safety Solar LED lights. © BLIKIR.Inc, All rights reserved. BLIKIR and the BLIKIR logo are trademarks or registered trademarks of BLIKIR, Inc. Date: 08G4/2023/V02/ENG. Subject to change without notice...
Need help?
Do you have a question about the RCP-2 G4 and is the answer not in the manual?
Questions and answers