Toro 75750W Operator's Manual
Hide thumbs Also See for 75750W:
Table of Contents

Advertisement

Register at www.Toro.com.
Original Instructions (EN)
TimeCutter
Riding Mower
Model No. 75750—Serial No. 407800000 and Up
Model No. 75750W—Serial No. 407150000 and Up
Model No. 75759—Serial No. 407700000 and Up
Form No. 3441-868 Rev A
®
5000 or MX 5000
*3441-868*

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 75750W and is the answer not in the manual?

Questions and answers

Summary of Contents for Toro 75750W

  • Page 1 Form No. 3441-868 Rev A TimeCutter ® 5000 or MX 5000 Riding Mower Model No. 75750—Serial No. 407800000 and Up Model No. 75750W—Serial No. 407150000 and Up Model No. 75759—Serial No. 407700000 and Up *3441-868* Register at www.Toro.com. Original Instructions (EN)
  • Page 2 Authorized Service requirements, the actual engine torque on this class Dealer or Toro Customer Service and have the model of mower will be significantly lower. Please refer to and serial numbers of your product ready.
  • Page 3: Table Of Contents

    Contents accidents. This symbol will appear with the word Danger, Warning, or Caution. • Danger indicates an imminently hazardous Safety ............... 4 situation which, if not avoided, will result in death General Safety ........... 4 or serious injury. Slope Indicator ........... 5 Safety and Instructional Decals ......
  • Page 4: Safety

    Safety Checking the Tire Pressure....... 39 Releasing the Electric Brake ......39 Adjusting the Tracking ........39 This machine has been designed in accordance with Belt Maintenance ..........40 ANSI B71.1-2017. Inspecting the Belts .......... 40 Replacing the Mower Belt ......... 40 Mower Maintenance..........
  • Page 5: Slope Indicator

    Slope Indicator g011841 Figure 3 You may copy this page for personal use. 1. The maximum slope you can operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope.
  • Page 6: Safety And Instructional Decals

    Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decalbatterysymbols Battery Symbols Some or all of these symbols are on your battery. 1.
  • Page 7 decal138-2456 138-2456 1. Read the Operator’s 3. Do not overfill the fuel Manual. tank. 2. Park the machine on a level surface when filling the fuel tank. decal121-2989b 121-2989 1. Bypass lever position for 2. Bypass lever position for pushing the machine operating the machine decal132-0872 132-0872...
  • Page 8 decal139-2395 139-2395 1. Parking brake 4. Neutral 2. Fast 5. Reverse 3. Slow 6. Traction controls decal139-2392 139-2392 decal139-2394 139-2394 1. Traction controls 4. Neutral 2. Fast 5. Reverse 3. Slow 6. Parking brake...
  • Page 9 Decal 132-0869 is for models with MyRide only. decal132-0869 132-0869 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operator’s Manual as well as the conditions in which you would operate the machine to determine whether you can operate the machine in the conditions on that day and at that site.
  • Page 10 Decal 135-3295 is for models without MyRide only. decal135-3295 135-3295 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operator’s Manual as well as the conditions in which you would operate the machine to determine whether you can operate the machine in the conditions on that day and at that site.
  • Page 11: Product Overview

    Product Overview g298516 Figure 4 Models with MyRide 1. Engine 4. Motion-control levers 7. Deck-lift pedal 10. Rear drive wheel 2. Operator seat 5. Front caster wheel 8. Height-of-cut lever 11. Control panel 3. Fuel-tank cap 6. Smart Speed™ lever 9.
  • Page 12 g299962 Figure 5 Models without MyRide 1. Deck-lift pedal 4. Motion-control levers 7. Fuel-tank cap 10. Deflector 2. Smart Speed™ lever 5. Control panel 8. Anti-scalp roller 6. Engine 9. Front caster wheel 3. Height-of-cut lever...
  • Page 13: Controls

    Controls Park Position Move the motion-control levers outward from the Become familiar with all the controls before you start center to the P position when exiting the machine the engine and operate the machine. to engage the electric brake (Figure 22).
  • Page 14: Before Operation

    Authorized Service Dealer or authorized Toro the operation of the machine or that the machine distributor or go to www.Toro.com for a list of all could throw. approved attachments and accessories.
  • Page 15: Adding Fuel

    Fuel Safety compartment to help prevent fires. Clean up oil or fuel spills. • Fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Adding Fuel – To prevent a static charge from igniting the fuel, place the container and/or machine directly on Recommended Fuel the ground before filling, not in a vehicle or on...
  • Page 16: Performing Daily Maintenance

    Understanding the Safety-Interlock System The safety-interlock system is designed to prevent the engine from starting unless: • The blade-control switch (PTO) is disengaged. • The motion-control levers are in the P position. The safety-interlock system also is designed to shut off the engine whenever the control levers are out of the P position and you rise from the seat.
  • Page 17: Positioning The Seat

    Positioning the Seat Adjusting the MyRide™ Suspension System The seat can move forward and backward. Position the seat where you have the best control of the Machines with MyRide Only machine and are most comfortable (Figure 9 Figure 10). The MyRide™ suspension system adjusts to provide a smooth and comfortable ride.
  • Page 18: Adjusting The Motion-Control Levers

    Adjusting the During Operation Motion-Control Levers During Operation Safety Adjusting the Height General Safety You can adjust the motion-control levers higher or • The owner/operator can prevent and is responsible lower for maximum comfort (Figure 12). for accidents that may cause personal injury or property damage.
  • Page 19 The operator is responsible for • Use only accessories and attachments approved safe slope operation. Operating the machine on by Toro. any slope requires extra caution. Before using the machine on a slope, do the following: •...
  • Page 20: Operating The Mower Blade-Control Switch (Pto)

    Operating the Mower These can change the stability of the machine and cause a loss of control. Follow directions for Blade-Control Switch (PTO) counterweights. • If possible, keep the deck lowered to the ground The blade-control switch (PTO) starts and stops the while operating on slopes.
  • Page 21: Operating The Throttle

    Operating the Throttle Starting the Engine You can move the throttle control between the F Note: A warm or hot engine may not require choking. and S positions (Figure 19). Important: Do not engage the starter for more Always use the F position when engaging the PTO.
  • Page 22: Shutting Off The Engine

    Shutting Off the Engine Driving the Machine Disengage the blades by moving the The drive wheels turn independently, powered by blade-control switch to the O position (Figure hydraulic motors on each axle. You can turn 1 side 18). in reverse while you turn the other forward, causing the machine to spin rather than turn.
  • Page 23: Using The Smart Speed Tm Control System

    Driving Backward Disengage the blade-control switch. Adjust the lever to the desired position. Move the levers to the center, unlocked position. To go backward, slowly pull the motion-control The following are only recommendations for use. levers rearward (Figure 24). Adjustments vary by grass type, moisture content, and the height of the grass.
  • Page 24: Using The Side Discharge

    Using the Side Discharge Adjusting the Height of Cut Note: The mower has a hinged grass deflector that The transport position is the highest disperses clippings to the side and down toward the height-of-cut position or cutting height at 114 mm turf.
  • Page 25: Adjusting The Anti-Scalp Rollers

    Adjusting the Anti-Scalp Operating Tips Rollers Using the Fast Throttle Setting Whenever you change the height of cut, adjust the For best mowing and maximum air circulation, operate height of the anti-scalp rollers. the engine at the F position. Air is required to thoroughly cut grass clippings, so do not set the Note: Adjust the anti-scalp rollers so that the rollers...
  • Page 26: After Operation

    Check the mower blades after each use for sharpness, and for any wear or damage. File down any nicks and sharpen the blades as necessary. If a blade is damaged or worn, replace it immediately with a genuine Toro replacement blade.
  • Page 27: Pushing The Machine By Hand

    Pushing the Machine by Hand Important: Always push the machine by hand. Do not tow the machine, because towing may damage it. This machine has an electric-brake mechanism, and to push the machine, the key must be in the position. The battery needs to be charged and functioning to disengage the electric brake.
  • Page 28 WARNING Driving on the street or roadway without turn signals, lights, reflective markings, or a slow-moving-vehicle emblem is dangerous and can lead to accidents, causing personal injury. Do not drive the machine on a public street or roadway. Selecting a Trailer WARNING Loading a machine onto a trailer or truck increases the possibility of tip-over and could...
  • Page 29 If using a trailer, connect it to the towing vehicle and connect the safety chains. If applicable, connect the trailer brakes and lights. Lower the ramp, ensuring that the angle between the ramp and the ground does not exceed 15 degrees (Figure 29).
  • Page 30: Maintenance

    • To ensure optimum performance, use only • Carefully release pressure from components with genuine Toro replacement parts and accessories. stored energy. Replacement parts and accessories made by • Check the parking brake operation frequently.
  • Page 31: Pre-Maintenance Procedures

    Maintenance Service Maintenance Procedure Interval • Check and adjust the valve clearance. Contact an Authorized Service Dealer. Every 300 hours • Charge the battery and disconnect the battery cables. • Perform all maintenance procedures listed above before storage. Before storage •...
  • Page 32: Engine Maintenance

    Engine Maintenance Servicing the Paper Air-Cleaner Element Engine Safety Service Interval: Every 100 hours or yearly, whichever comes first—Replace the • Keep your hands, feet, face, clothing, and other paper air-cleaner element (more body parts away from the muffler and other hot often in dirty or dusty conditions).
  • Page 33: Servicing The Engine Oil

    Servicing the Engine Oil Engine-Oil Specifications Oil Type: Detergent oil (API service SF, SG, SH, SJ, or SL) Crankcase Capacity: 1.8 L (61 fl oz); without filter; 2.1 L (70 fl oz) with filter Viscosity: See the table below. g331234 Figure 35 g194611 Figure 36...
  • Page 34 Changing the Engine-Oil Filter Service Interval: Every 200 hours—Change the engine-oil filter (more often in dirty or dusty conditions). Drain the oil from the engine; refer to Changing the Engine Oil (page 33). Change the engine-oil filter (Figure 39). g027539 Figure 37 Slowly pour approximately 80% of the specified oil into the filler tube and slowly add the...
  • Page 35: Servicing The Spark Plug

    Servicing the Spark Plug Service Interval: Every 100 hours Ensure that the air gap between the center and side electrodes is correct before installing the spark plug. Use a spark plug wrench for removing and installing the spark plug and a gapping tool or feeler gauge to check and adjust the air gap.
  • Page 36: Fuel System Maintenance

    Fuel System Maintenance DANGER g027590 In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Refer to Fuel Safety (page 15) for a complete list of fuel related precautions. Replacing the In-Line Fuel Filter Service Interval: Every 100 hours—Replace the...
  • Page 37: Electrical System Maintenance

    Electrical System WARNING Incorrectly removing the cables from Maintenance battery could damage the machine and cables, causing sparks. Sparks can cause the battery gasses to explode, Electrical System Safety resulting in personal injury. • Disconnect the battery before repairing the •...
  • Page 38: Servicing The Fuses

    Charging the Battery Servicing the Fuses Service Interval: Before storage—Charge the battery The electrical system is protected by fuses. It requires and disconnect the battery cables. no maintenance; however, if a fuse blows, check the component/circuit for a malfunction or short. Remove the battery from the chassis;...
  • Page 39: Drive System Maintenance

    Releasing the Electric Drive System Brake Maintenance You can manually release the electric brake by rotating the link arms forward. Once the electric brake Checking the Tire Pressure is energized, the brake resets. Service Interval: Every 25 hours—Check tire Turn the key to the position and remove pressure.
  • Page 40: Belt Maintenance

    Repeat the procedure as needed. g331652 Figure 50 1. Cover 2. Hairpin cotter Using a spring-removal tool (Toro Part No. 92-5771), remove the idler spring from the deck hook to remove tension on the idler pulley, and roll the belt off the pulleys (Figure...
  • Page 41: Mower Maintenance

    (Figure 51). plugs. Using a spring-removal tool (Toro Part No. 92-5771), install the idler spring over the deck Inspecting the Blades hook and place tension on the idler pulley and the mower belt (Figure 51).
  • Page 42 g006530 Figure 52 1. Cutting edge 3. Wear/slot forming g014973 Figure 54 2. Curved area 4. Crack 1. Blade (in position for measuring) 2. Level surface Checking for Bent Blades 3. Measured distance between blade and the surface (A) Note: The machine must be on a level surface for Rotate the same blade 180 degrees so that the following procedure.
  • Page 43 g014973 Figure 56 g027833 1. Opposite blade edge (in position for measuring) Figure 57 2. Level surface 1. Sail area of the blade 3. Curved washer 3. Second measured distance between blade and surface (B) 2. Blade 4. Blade bolt If the difference between A and B is greater than 3 mm (1/8 inch), replace the blade with Sharpening the Blades...
  • Page 44: Leveling The Mower Deck

    Installing the Blades Install the blade onto the spindle shaft (Figure 57). Important: The curved part of the blade must be pointing upward toward the inside of the mower to ensure proper cutting. Install the curved washer (cupped side toward the blade) and the blade bolt (Figure 57).
  • Page 45 g296914 Figure 61 1. Blades front to rear 3. Measure from the tip of the blade to the flat surface g298028 here. Figure 62 2. Outside cutting edges 1. Wood block—6.6 cm 2. Wood block—7.3 cm (2-5/8 inches) thick (2-7/8 inches) thick Leveling from Side to Side Remove the hairpin cotter and washer from the lower lift-arm pin...
  • Page 46: Removing The Mower Deck

    To lower the front of the mower, loosen the adjustment nut. After adjustment, check the front-to-rear slope again, continue adjusting the nut until the front blade tip is 1.6 to 7.9 mm (1/16 to 5/16 inch) lower than the rear blade tip; refer to Checking the Front-to-Rear Blade Slope (page 44).
  • Page 47: Installing The Mower Deck

    Attach the front support rod to the mower deck with the clevis pin and hairpin cotter (Figure 66). Install the mower belt onto the engine pulley; refer to Replacing the Mower Belt (page 40). g295768 Figure 67 1. Lift arm 3.
  • Page 48: Cleaning

    Cleaning Disengage the blade-control switch, shut off the engine, remove the key, and wait for all moving parts to stop. Washing the Underside of Turn the water off and remove the coupling from the washout fitting. the Mower Deck Note: If the mower is not clean after 1 washing, Service Interval: After each use—Clean the soak it and let it stand for 30 minutes.
  • Page 49: Storage

    Storage Check the condition of the blades; refer to Servicing the Cutting Blades (page 41). Prepare the machine for storage for over Storage Safety 30 days as follows: • Shut off the engine, remove the key, and wait Add fuel stabilizer/conditioner to fresh fuel for all moving parts to stop before you leave the in the tank.
  • Page 50: Storing The Battery

    Storing the Battery Fully charge the battery. Let the battery rest for 24 hours, then check the battery voltage. Note: If the battery voltage is below 12.6 V, repeat steps and 2. Disconnect the cables from the battery. Check the voltage periodically to ensure that the voltage is 12.4 V or higher.
  • Page 51: Troubleshooting

    Troubleshooting Problem Possible Cause Corrective Action The fuel tank is showing signs of collapsing 1. The air-cleaner paper element clogged. 1. Clean the paper element. or the machine is frequently showing signs of running out of fuel. The engine overheats. 1.
  • Page 52 Problem Possible Cause Corrective Action The machine does not drive. 1. The bypass valves are open. 1. Close the tow valves. 2. The traction belts are worn, loose, or 2. Contact an Authorized Service Dealer. broken. 3. The traction belts are off the pulleys. 3.
  • Page 53: Schematics

    Schematics g307974 Electrical Diagram—139–2356 (Rev. A)
  • Page 54 Notes:...
  • Page 55 Notes:...
  • Page 56 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.

This manual is also suitable for:

Timecutter mx 500075750Timecutter 500075759

Table of Contents

Save PDF