Table of Contents
Advertisement
Quick Links
Register at www.Toro.com.
Original Instructions (EN)
TimeCutter
5475 Riding Mower
Model No. 75745—Serial No. 407700000 and Up
Model No. 75745TA—Serial No. 407530000 and Up
Model No. 75745W—Serial No. 407200000 and Up
Model No. 75754—Serial No. 407700000 and Up
Model No. 75755—Serial No. 407700000 and Up
Model No. 75755TA—Serial No. 407600000 and Up
Model No. 75755W—Serial No. 407200000 and Up
Form No. 3441-874 Rev A
®
MX 4275, 5075, or
*3441-874*
Advertisement
Table of Contents
Related Manuals for Toro 75745W
Summary of Contents for Toro 75745W
- Page 1 5475 Riding Mower Model No. 75745—Serial No. 407700000 and Up Model No. 75745TA—Serial No. 407530000 and Up Model No. 75745W—Serial No. 407200000 and Up Model No. 75754—Serial No. 407700000 and Up Model No. 75755—Serial No. 407700000 and Up Model No. 75755TA—Serial No. 407600000 and Up Model No.
- Page 2 California to cause cancer, birth defects, or other reproductive harm. Important: If you are using a machine with a Toro engine above 1500 m (5,000 ft) for a continuous period, ensure that the High Altitude Kit has been installed so that the engine meets CARB/EPA emission regulations.
-
Page 3: Table Of Contents
Whenever you need service, genuine Toro parts, or Figure 2 additional information, contact an Authorized Service 1. Safety-alert symbol Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. -
Page 4: Safety
Safety After Operation Safety ........24 Pushing the Machine by Hand ......25 Transporting the Machine ......... 25 This machine has been designed in accordance with Maintenance ............28 ANSI B71.1-2017. Maintenance Safety.......... 28 Recommended Maintenance Schedule(s) ... 28 Pre-Maintenance Procedures ......30 General Safety Raising the Machine ......... -
Page 5: Slope Indicator
Slope Indicator g011841 Figure 4 You may copy this page for personal use. 1. The maximum slope you can operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. -
Page 6: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. Decal 99-3943 is for models with 127 cm (50 inch) or 137 cm (54 inch) decks. - Page 7 decal132-0872 132-0872 decal112-9840 112-9840 1. Thrown object 3. Severing hazard of hand hazard—keep bystanders or foot—keep away from 1. Read the Operator's 3. Remove the ignition key away from the machine. moving parts. Manual. and read the instructions 2. Thrown object hazard, 4.
- Page 8 decal139-2388 139-2388 3. Fast 1. Slow 2. Hauling decal139-2392 139-2392 decal139-2391 decal139-2394 139-2391 139-2394 1. Fast 2. Slow 1. Traction controls 4. Neutral 2. Fast 5. Reverse 3. Slow 6. Parking brake...
- Page 9 decal139-2397 139-2397 decal139-2395 139-2395 1. Parking brake 4. Neutral 2. Fast 5. Reverse 3. Slow 6. Traction controls decal132-0869 132-0869 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal.
-
Page 10: Product Overview
Product Overview g292025 Figure 5 1. Engine 4. Motion-control levers 7. Deck-lift pedal (certain 10. Rear drive wheel models only) 2. Operator seat 5. Front caster wheel 8. Height-of-cut lever 11. Control panel 3. Fuel-tank cap 6. Smart Speed™ lever 9. -
Page 11: Controls
Controls Park Position Move the motion-control levers outward from the Become familiar with all the controls before you start center to the P position when exiting the machine the engine and operate the machine. to engage the electric brake (Figure 21). -
Page 12: Before Operation
Contact your Authorized Service Dealer or authorized Toro • Become familiar with the safe operation of the distributor or go to www.Toro.com for a list of all equipment, operator controls, and safety signs. approved attachments and accessories. •... -
Page 13: Adding Fuel
Fuel Safety compartment to help prevent fires. Clean up oil or fuel spills. • Fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Adding Fuel – To prevent a static charge from igniting the fuel, place the container and/or machine directly on Recommended Fuel the ground before filling, not in a vehicle or on... -
Page 14: Performing Daily Maintenance
Understanding the Safety-Interlock System The safety-interlock system is designed to prevent the engine from starting unless: • The blade-control switch (PTO) is disengaged. • The motion-control levers are in the P position. The safety-interlock system also is designed to shut off the engine whenever the control levers are out of the P position and you rise from the seat. -
Page 15: Positioning The Seat
Positioning the Seat Adjusting the MyRide™ Suspension System The seat can move forward and backward. Position the seat where you have the best control of the The MyRide™ suspension system adjusts to provide a machine and are most comfortable (Figure smooth and comfortable ride. -
Page 16: Adjusting The Motion-Control Levers
Adjusting the During Operation Motion-Control Levers During Operation Safety Adjusting the Height General Safety You can adjust the motion-control levers higher or • The owner/operator can prevent and is responsible lower for maximum comfort (Figure 11). for accidents that may cause personal injury or property damage. - Page 17 The operator is responsible for • Use only accessories and attachments approved safe slope operation. Operating the machine on by Toro. any slope requires extra caution. Before using the machine on a slope, do the following: •...
-
Page 18: Operating The Mower Blade-Control Switch (Pto)
Operating the Mower These can change the stability of the machine and cause a loss of control. Follow directions for Blade-Control Switch (PTO) counterweights. • If possible, keep the deck lowered to the ground The blade-control switch (PTO) starts and stops the while operating on slopes. -
Page 19: Operating The Throttle
Operating the Throttle Starting the Engine You can move the throttle control between the F Note: A warm or hot engine may not require choking. and S positions (Figure 18). Important: Do not engage the starter for more Always use the F position when engaging the PTO. -
Page 20: Shutting Off The Engine
Shutting Off the Engine Driving the Machine Disengage the blades by moving the The drive wheels turn independently, powered by blade-control switch to the O position (Figure hydraulic motors on each axle. You can turn 1 side 20). in reverse while you turn the other forward, causing the machine to spin rather than turn. -
Page 21: Using The Smart Speed Control System
Driving Backward Disengage the blade-control switch. Adjust the lever to the desired position. Move the levers to the center, unlocked position. To go backward, slowly pull the motion-control The following are only recommendations for use. levers rearward (Figure 23). Adjustments vary by grass type, moisture content, and the height of the grass. -
Page 22: Using The Side Discharge
Using the Side Discharge Adjusting the Height of Cut Note: The mower has a hinged grass deflector that The transport position is the highest disperses clippings to the side and down toward the height-of-cut position or cutting height at 114 mm turf. -
Page 23: Operating Tips
motion-control levers outward to the P position. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Adjust the anti-scalp rollers to 1 of the following positions: • Upper hole—use this position with the mower deck in the 63 mm (2-1/2 inches) and below the height-of-cut positions (Figure... -
Page 24: After Operation
Check the mower blades after each use for sharpness, and for any wear or damage. File down any nicks and sharpen the blades as necessary. If a blade is damaged or worn, replace it immediately with a genuine Toro replacement blade. -
Page 25: Pushing The Machine By Hand
Pushing the Machine by Hand Important: Always push the machine by hand. Do not tow the machine, because towing may damage it. This machine has an electric-brake mechanism, and to push the machine, the key must be in the position. The battery needs to be charged and functioning to disengage the electric brake. - Page 26 WARNING Driving on the street or roadway without turn signals, lights, reflective markings, or a slow-moving-vehicle emblem is dangerous and can lead to accidents, causing personal injury. Do not drive the machine on a public street or roadway. Selecting a Trailer WARNING Loading a machine onto a trailer or truck increases the possibility of tip-over and could...
- Page 27 If using a trailer, connect it to the towing vehicle and connect the safety chains. If applicable, connect the trailer brakes and lights. Lower the ramp, ensuring that the angle between the ramp and the ground does not exceed 15 degrees (Figure 29).
-
Page 28: Maintenance
• To ensure optimum performance, use only • Carefully release pressure from components with genuine Toro replacement parts and accessories. stored energy. Replacement parts and accessories made by • Check the parking brake operation frequently. - Page 29 Maintenance Service Maintenance Procedure Interval • Check and adjust the valve clearance. Contact an Authorized Service Dealer. Every 300 hours • Charge the battery and disconnect the battery cables. • Perform all maintenance procedures listed above before storage. Before storage •...
-
Page 30: Pre-Maintenance Procedures
Pre-Maintenance Lubrication Procedures Greasing the Bearings Raising the Machine Service Interval: Every 25 hours—Grease the caster wheel bearings. Use jackstands to support the machine when you Grease Type: No. 2 lithium grease raise it. Park the machine on a level surface, disengage the blade-control switch, and move the WARNING motion-control levers outward to the P... -
Page 31: Engine Maintenance
Engine Maintenance Engine Safety • Keep your hands, feet, face, clothing, and other body parts away from the muffler and other hot surfaces. Allow engine components to cool before performing maintenance. • Do not change the engine governor speed or overspeed the engine. - Page 32 Servicing the Foam Air-Cleaner Installing the Air Cleaner Element Install the foam element over the paper element. Service Interval: Every 25 hours/Monthly (whichever Note: Ensure that you do not damage the comes first)—Clean the air-cleaner elements. foam element (more often in dusty, Align the holes of the filter into the manifold dirty conditions).
-
Page 33: Servicing The Engine Oil
Servicing the Engine Oil Engine-Oil Specifications Oil Type: Detergent oil (API service SF, SG, SH, SJ, or SL) Crankcase Capacity: 2.4 L (81 fl oz) with oil filter Viscosity: See the table below. g029683 Figure 37 Checking the Engine-Oil Level Service Interval: Before each use or daily Note: Check the oil when the engine is cold. - Page 34 Change the engine-oil filter (Figure 40). Note: Ensure that the oil-filter gasket touches the engine and then turn the filter an extra 3/4 turn. g027799 g027477 Figure 40 Slowly pour approximately 80% of the specified oil into the filler tube and slowly add the additional oil to bring it to the Full mark (Figure 41).
-
Page 35: Servicing The Spark Plug
g027478 Figure 42 Checking the Spark Plug Important: Do not clean the spark plug(s). Always replace the spark plug(s) when it has a black coating, worn electrodes, an oily film, or cracks. If you see light brown or gray on the insulator, the engine is operating properly. -
Page 36: Cleaning The Cooling System
Cleaning the Cooling Fuel System System Maintenance Park the machine on a level surface, disengage the blade-control switch, and move the DANGER motion-control levers outward to the P In certain conditions, fuel is extremely position. flammable and highly explosive. A fire or Shut off the engine, remove the key, and wait explosion from fuel can burn you and others for all moving parts to stop before leaving the... -
Page 37: Electrical System Maintenance
Electrical System Maintenance Electrical System Safety • Disconnect the battery before repairing the g027939 machine. Disconnect the negative terminal first and the positive last. Connect the positive terminal first and the negative last. • Charge the battery in an open, well-ventilated area, away from sparks and flames. - Page 38 Charging the Battery WARNING Incorrectly removing the cables from Service Interval: Before storage—Charge the battery and disconnect the battery cables. battery could damage the machine and cables, causing sparks. Sparks can Remove the battery from the chassis; refer to cause the battery gasses to explode, Removing the Battery (page 37).
-
Page 39: Drive System Maintenance
Drive System Maintenance Checking the Tire Pressure Service Interval: Every 25 hours—Check tire pressure. Maintain the air pressure in the front and rear tires as g294417 specified. Uneven tire pressure can cause an uneven Figure 49 cut. Check the pressure at the valve stem (Figure 48). -
Page 40: Belt Maintenance
Figure 51 1. Cover 2. Hairpin cotter Using a spring-removal tool (Toro Part No. 92-5771), remove the idler spring from the deck hook to remove tension on the idler pulley, and roll the belt off the pulleys (Figure 52 Figure 53). - Page 41 1. Idler pulley 4. Spring 2. Mower belt 5. Engine pulley Using a spring-removal tool (Toro Part No. 3. Outside pulley 6. Spring-removal tool 92-5771), install the idler spring over the deck hook and place tension on the idler pulley and...
-
Page 42: Mower Maintenance
Mower Maintenance Blade Safety • Inspect the blades periodically for wear or damage. • Use care when checking the blades. Wrap the blades or wear gloves, and use caution when servicing the blades. Only replace or sharpen the g006530 blades; never straighten or weld them. Figure 54 •... - Page 43 g014973 g014973 Figure 56 Figure 58 1. Blade (in position for measuring) 1. Opposite blade edge (in position for measuring) 2. Level surface 2. Level surface 3. Measured distance between blade and the surface (A) 3. Second measured distance between blade and surface (B) Rotate the same blade 180 degrees so that If the difference between A and B is greater the opposing cutting edge is now in the same...
-
Page 44: Leveling The Mower Deck
Installing the Blades Install the blade onto the spindle shaft (Figure 59). Important: The curved part of the blade must be pointing upward toward the inside of the mower to ensure proper cutting. Install the curved washer (cupped side toward the blade) and the blade bolt (Figure 59). - Page 45 Set the height of cut to 76 mm (3 inches). Carefully rotate the blades so they are facing front to rear (Figure 64). Measure from the tip of the front blade to the flat surface and the tip of the rear blade to the flat surface (Figure 64 Figure...
- Page 46 Leveling from Side to Side Move to the left side of the machine. Set the anti-scalp rollers to the top holes or remove them completely for this procedure; refer Adjusting the Anti-Scalp Rollers (page 22). Set the height-of-cut lever to the 76 mm (3 inch) position;...
-
Page 47: Removing The Mower Deck
To lower the front of the mower, loosen the adjustment nut. After adjustment, check the front-to-rear slope again, continue adjusting the nut until the front blade tip is 1.6 to 7.9 mm (1/16 to 5/16 inch) lower than the rear blade tip; refer to Checking the Front-to-Rear Blade Slope (page 45). -
Page 48: Installing The Mower Deck
Attach the front support rod to the mower deck with the clevis pin and hairpin cotter (Figure 71). Install the mower belt onto the engine pulley; refer to Replacing the Mower Belt (page 40). Replacing the Grass Deflector Service Interval: Before each use or daily—Inspect the grass deflector for damage. -
Page 49: Cleaning
Cleaning Slide the rod through the second grass-deflector bracket (Figure 73). Insert the rod at the front of the grass deflector Washing the Underside of into the short standoff on the deck. the Mower Deck Secure the rear end of the rod into the mower with a nut (3/8 inch) as shown in Figure Service Interval: After each use—Clean the... -
Page 50: Disposing Of Waste
Storage Disengage the blade-control switch, shut off the engine, remove the key, and wait for all moving parts to stop. Storage Safety Turn the water off and remove the coupling from the washout fitting. • Shut off the engine, remove the key, and wait for all moving parts to stop before you leave the Note: If the mower is not clean after 1 washing,... -
Page 51: Storing The Battery
Storing the Battery Check the condition of the blades; refer to Servicing the Cutting Blades (page 42). Fully charge the battery. Prepare the machine for storage for over Let the battery rest for 24 hours, then check the 30 days as follows: battery voltage. -
Page 52: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The fuel tank is showing signs of collapsing 1. The air-cleaner paper element clogged. 1. Clean the paper element. or the machine is frequently showing signs of running out of fuel. The engine overheats. 1. - Page 53 Problem Possible Cause Corrective Action The machine does not drive. 1. The bypass valves are open. 1. Close the tow valves. 2. The traction belts are worn, loose, or 2. Contact an Authorized Service Dealer. broken. 3. The traction belts are off the pulleys. 3.
-
Page 54: Schematics
Schematics g307974 Electrical Diagram 139-2356 (Rev. A) - Page 55 Notes:...
- Page 56 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.