Related Manuals for Yamaha WaveRunner SuperJet 2015
Summary of Contents for Yamaha WaveRunner SuperJet 2015
- Page 1 2015 WaveRunner SuperJet OWNER’S/OPERATOR’S MANUAL Read this manual carefully before operating this watercraft. F4D-28199-70-E0...
- Page 2 IMPORTANT NOTICE This personal watercraft is intended solely for rac- ing. The use of this machine should be limited to designated areas or events. Read this manual carefully before operating this watercraft. This manual should stay with the WaveRunner if it is sold.
- Page 3 Important manual information EJU3008B Declaration of Conformity Name of PWC Manufacturer: YAMAHA MOTOR CO., LTD. Address: 2500 Shingai, Iwata, Shizuoka 438-8501, Japan Name of Authorised Representative: YAMAHA MOTOR EUROPE N.V. Address: Koolhovenlaan 101, 1119 NC Schiphol-Rijk, The Netherlands CONFORMITY Directives...
- Page 4 Important manual information EJU30193 EJU40411 To the owner/operator Thank you for choosing a Yamaha watercraft. Because Yamaha has a policy of continuing This owner’s/operator’s manual contains in- product improvement, this product may not formation you will need for proper operation, be exactly as described in this owner’s/oper-...
-
Page 5: Table Of Contents
Table of contents Equipment operation ...... 24 General and important labels... 1 Equipment........24 Identification numbers ....1 Hood..........24 Primary Identification (PRI-ID) Bow rope hole ........25 number..........1 Stern rope hole......... 25 Craft Identification Number (CIN) ..1 Storage pouch........ - Page 6 Table of contents Capsized watercraft ......48 Index..........70 Beaching the watercraft ....49 Operating in weeded areas ....49 After removing the watercraft from the water ........49 Care and storage......50 Post-operation care ...... 50 Flushing the cooling water passages........
-
Page 7: General And Important Labels
Craft Identification Number (CIN), and engine serial number in the spaces pro- vided for assistance when ordering spare parts from a Yamaha dealer. Also record and keep these ID numbers in a separate place in case your watercraft is stolen. -
Page 8: Manufactured Date Label
General and important labels EJU41742 Manufactured date label This label is attached to the muffler. (See page 24 for hood removal and installation procedures.) 1 Manufactured date label location... -
Page 9: Important Labels
General and important labels EJU30453 Important labels Read the following labels before using this watercraft. If have any questions, consult a Yamaha dealer. -
Page 10: Warning Labels
General and important labels EJU35914 Warning labels If any of these labels are damaged or missing, contact a Yamaha dealer for replacements. - Page 11 General and important labels...
- Page 12 General and important labels...
-
Page 13: Other Labels
General and important labels EJU35926 Other labels The following label indicates the correct direction to upright a capsized watercraft. F2F-6418F-00... -
Page 14: Safety Information
Limitations on who may The safe use and operation of this water- operate the watercraft craft is dependent upon the use of proper Yamaha recommends a minimum operator riding techniques, as well as upon the age of 16 years old. -
Page 15: Cruising Limitations
Safety information (paralysis), facial injuries, and broken legs, EJU30762 Cruising limitations ankles, and other bones. Do not jump Scan constantly for people, objects, and wakes or waves. other watercraft. Be alert for conditions Do not operate the watercraft in rough wa- ... -
Page 16: Operation Requirements
Safety information colliding with another boat, which could re- EJU30782 Operation requirements sult in severe injury or death. All riders must wear a personal flotation de- vice (PFD) that is approved by the appro- priate authorities and is suitable for personal watercraft use. - Page 17 Safety information in certain kinds of accidents and that it the chances of losing your balance or hit- could injure you in others. ting objects outside the watercraft with A helmet is designed to provide some head your feet. protection. Although helmets cannot pro- tect against all foreseeable impacts, a hel- met might reduce your injuries in a collision with a boat or other obstacle.
-
Page 18: Recommended Equipment
14.) tainer on your watercraft. A mirror can also be used as an emergency signal. Contact a Yamaha dealer for more information. Watch A watch is helpful so you will know how long you have been operating the water- craft. -
Page 19: Hazard Information
Safety information EJU30851 EJU30881 Hazard information Watercraft characteristics When transporting or storing your water- Jet thrust turns the watercraft. Releasing craft, always turn the fuel cock knob to the throttle lever completely produces only “OFF”, otherwise gasoline may overflow minimum thrust. -
Page 20: Safe Boating Rules
EJU30971 Safe boating rules pump. Your Yamaha watercraft is legally considered a powerboat. Operation of the watercraft must be in accordance with the rules and regulations governing the waterway on which it is used. -
Page 21: Enjoy Your Watercraft Responsibly
Safety information When you ride responsibly, with respect and EJU30992 Enjoy your watercraft courtesy for others, you help ensure that our responsibly waterways stay open for the enjoyment of a You share the areas you enjoy when riding variety of recreational opportunities. your watercraft with others and with nature. -
Page 22: Description
Description EJU40653 Watercraft glossary Trolling speed “Trolling” is the lowest maneuvering speed. You are applying little or no throttle. The water- craft is down in the water, and there is no wake. Sub-planing speed “Sub-planing” is a medium speed. The bow of the watercraft is slightly up from the water sur- face, but you are still traveling through the water. -
Page 23: Location Of Main Components
Description EJU31012 Location of main components 15 16 1 Steering pole 2 Steering pole cover 3 Bow rope hole 4 Fuel filler cap 5 Cooling water pilot outlet 6 Hood 7 Hood latch 8 Handlebar 9 Storage pouch 10 Riding tray 11 Stern rope hole 12 Jet thrust nozzle 13 Ride plate... - Page 24 Description 1 Fire extinguisher container 2 Fuel cock knob 3 Choke knob 4 Clip 5 Start switch 6 Throttle lever 7 Engine shut-off cord (lanyard) 8 Engine stop switch 9 Engine shut-off switch 10 Fuel tank 11 Battery 12 Silencer 13 Spark plug/Spark plug cap 14 Water separator 15 Muffler...
-
Page 25: Control Function Operation
Control function operation vent accidental starting or unauthorized op- EJU31025 Watercraft control functions eration by children or others. EJU31153 Engine stop switch “ ” The engine stop switch (red button) stops the engine when the switch is pushed. EJU41051 Start switch “ ”... -
Page 26: Throttle Lever
Control function operation will not start. Also, the starter motor could zle is changed, and the direction of the water- be damaged. craft is changed accordingly. [ECJ01041] 1 Start switch 1 Handlebar 2 Jet thrust nozzle The engine will not start when the clip is re- Since the strength of the jet thrust determines moved from the engine shut-off switch. -
Page 27: Fuel Cock Knob
Control function operation fuel while operating the watercraft. When this EJU31124 Fuel cock knob occurs, refuel as soon as possible and be The fuel supply method can be switched by sure to turn the fuel cock knob back to “ON”. operating the fuel cock knob. -
Page 28: Water Separator
Control function operation proper operation of the cooling system, make If water has collected in the water separator, sure that water is being discharged from the drain it by loosening the drain screw. cooling water pilot outlet. If water is not being discharged from the outlet, stop the engine and check the jet intake for clogging. - Page 29 (See page 66 for information on the jet intake.) NOTICE: If you cannot locate and correct the cause of the overheating, con- sult a Yamaha dealer. Continuing to oper- ate at higher speeds could result in severe engine damage.
-
Page 30: Equipment Operation
Equipment operation (2) Turn the latch knob to the “OPEN” posi- EJU40334 Equipment tion, and then pull up on the hood latch EJU31057 to unlatch the hood. Hood The hood is removable. Remove the hood to access the engine com- partment. -
Page 31: Bow Rope Hole
Equipment operation To install the hood: towing it in an emergency. (See page 68 for (1) Position the hood on the deck so that the information on towing the watercraft.) two projections at the front of the hood fit under the two stays on the deck. 1 Bow rope hole EJU36012 Stern rope hole... -
Page 32: Fire Extinguisher Container
Equipment operation (2) Unfasten the bands, and then remove To open the fire extinguisher container: the storage pouch. (1) Lift the steering pole and support it with the lock pin. 1 Storage pouch 2 Band 1 Steering pole 2 Lock pin To install the storage pouch: (1) Bend the owner’s/operator’s manual (2) Grasp the tab, pull the band to the rear,... - Page 33 Equipment operation (4) Loosen the fire extinguisher container cap and remove it. 1 Fire extinguisher container cap To close the fire extinguisher container: (1) Insert the fire extinguisher into the con- tainer, and then securely install the fire extinguisher container cap by tightening it until it stops.
-
Page 34: Operation And Handling Requirements
Gasoline and gasoline vapors are ex- or engine performance problems. tremely flammable. To avoid fires and Yamaha does not recommend gasohol con- explosions and to reduce the risk of in- taining methanol because it can cause fuel jury when refueling, follow these in- system damage and engine performance structions. -
Page 35: Filling The Fuel Tank
Operation and handling requirements (2) To mix them thoroughly, shake the con- Fuel tank capacity: tainer from side to side. Total: 18 L (4.8 US gal, 4.0 Imp.gal) Reserve: 5.5 L (1.5 US gal, 1.2 Imp.gal) (6) Stop filling when the fuel level just reach- es the bottom of the filler tube. -
Page 36: Draining The Bilge Water
Operation and handling requirements engine, which can result in severe dam- EJU40022 Draining the bilge water age. [ECJ00554] ECJ01302 NOTICE Do not run the engine at full throttle when bilge water remains in the engine com- partment. The bilge water can splash into the engine, which can result in severe damage. -
Page 37: Transporting
Operation and handling requirements where they touch the body of the water- EJU33424 Transporting craft to avoid scratches or damage. [ECJ00633] EWJ00751 WARNING Always turn the fuel cock knob to “OFF” when transporting the watercraft, other- wise fuel could leak out into the engine or engine compartment, which would create a fire hazard. -
Page 38: First-Time Operation
First-time operation EJU32757 Engine break-in ECJ00432 NOTICE Failure to perform the engine break-in could result in reduced engine life or even severe engine damage. The engine break-in is essential to allow the various components of the engine to wear and polish themselves to the correct operat- ing clearances. -
Page 39: Pre-Operation Checks
Do not operate the watercraft if you find any prob- lem. If a problem cannot be corrected by the procedures provided in this manual, have the watercraft inspected by a Yamaha dealer. EJU41233 Pre-operation checklist Before using this watercraft, be sure to perform the checks in the following checklist. - Page 40 Pre-operation checks ITEM ROUTINE PAGE POST-LAUNCH CHECKS Check that water is discharged from the cooling Cooling water pilot outlet water pilot outlet while the engine is running. TIP: To ensure safety and reliability, pre-operation checks should be made each time the water- craft is used.
-
Page 41: Pre-Operation Check Points
Pre-operation checks If any fuel leakage is found, the fuel sys- EJU32282 Pre-operation check points tem must be repaired by a qualified me- EJU40686 chanic. Improper repairs can make the Pre-launch checks watercraft unsafe to operate. Perform the pre-launch checks in the pre-op- eration checklist while the watercraft is on Make sure that there is no damage, leakage, land. - Page 42 Pre-operation checks Add fuel if necessary. (See page 29 for infor- aged, obstructed, or not connected prop- mation on filling the fuel tank.) erly. [EWJ00452] EJU32424 Water separator check Make sure that no water has collected in the water separator. If water has collected in the water separator, drain it.
- Page 43 Pre-operation checks whole range, and that the free play is not ex- Difference between fully turned posi- cessive. tions of jet thrust nozzle (distances A and B): Maximum 5 mm (0.20 in) EJU32623 Steering pole check Move the steering pole up and down several times to make sure that operation is smooth and unrestricted throughout the whole range, and that the free play is not excessive.
- Page 44 Pre-operation checks Make sure that there is the proper amount of EJU41021 Switch checks throttle lever free play when the throttle lever ECJ01361 NOTICE is in the fully closed (idle) position. Do not run the engine for more than 15 seconds on land without supplying water, otherwise the engine could overheat.
-
Page 45: Post-Launch Checks
If you do not have one, Make sure that water is discharged from the contact a Yamaha dealer or a fire extinguish- cooling water pilot outlet while the engine is er dealer to obtain one meeting the proper running. -
Page 46: Operation
Operate defensively at safe speeds and keep familiar with all of the controls. Consult a a safe distance away from people, objects, Yamaha dealer about any control or func- and other watercraft. Select a wide area to tion that you do not fully understand. Fail-... -
Page 47: Launching The Watercraft
Operation wake, but the watercraft is moving through If the watercraft is launched from a trailer, the water rather than skimming on top of it.) someone should make sure that waves do not push the watercraft into the trailer. After the watercraft is in the water, turn it around so that the bow faces the direction you wish to go. - Page 48 Operation (2) Turn the fuel cock knob to “ON”. (4) Pull the choke knob all the way out to start a cold engine. (3) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip TIP: to the engine shut-off switch.
-
Page 49: Stopping The Engine
Operation throttle lever is in the fully closed (idle) posi- EJU32863 Stopping the engine tion. Release the throttle lever, and then push the engine stop switch (red button) to stop the engine. WARNING! You need throttle to steer. Shutting the engine off can cause you to hit an obstacle you are attempting to avoid. - Page 50 Operation A. More throttle produces higher thrust, so alone using just the amount of thrust the watercraft will turn more sharply. available at idle. B. Less throttle produces lower thrust, so D. If the engine is stopped while riding, the watercraft will turn more gradually. there is no thrust.
-
Page 51: Stopping The Watercraft
Operation general, the higher the speed or the sharper hitting an obstacle, apply throttle and turn in the turn, the more you lean. another direction. EWJ00723 WARNING Allow adequate stopping distance. Take early action to avoid collisions. Re- member, watercraft and other boats do not have brakes. - Page 52 Operation sharp turns or other maneuvers that gravity by operating it in the kneeling posi- make it hard for others to avoid you or tion. understand where you are going. Avoid Even though it is easier to start in shallow wa- areas with submerged objects or shal- ter, you must learn deep-water boarding first.
- Page 53 Operation (5) Pull your other knee up onto the riding left wrist, and then attach the clip to the tray as the watercraft speed increases. engine shut-off switch. (6) Move as far forward as possible without (2) Grip the handlebars with both hands. interfering with the movement of the han- Pull your body up onto the riding tray and dlebars.
-
Page 54: Capsized Watercraft
Operation (5) Bring your knees up onto the riding tray If the watercraft capsizes, turn it over imme- and change to a kneeling position as diately. soon as you can do so. To upright the watercraft: (1) Remove the clip from the engine shut-off switch. -
Page 55: Beaching The Watercraft
Operation see “Towing the watercraft” on page 68 area, clean the jet intake. (See page 66 for in- or “Submerged watercraft” on page 69.) formation on the jet intake.) NOTICE: Do not run the engine at full EJU41061 After removing the watercraft from throttle for at least 1 minute after the the water engine has been restarted. -
Page 56: Care And Storage
Care and storage (3) Connect the garden hose adapter to a EJU41192 Post-operation care garden hose. EWJ00321 WARNING Always turn the fuel cock knob to “OFF” when storing the watercraft, otherwise fuel could leak out into the engine or en- gine compartment, which would create a fire hazard. -
Page 57: Cleaning The Watercraft
Care and storage water flows out continually from the water when rinsing the engine or en- cooling water pilot outlet. gine compartment as severe engine damage could result. [ECJ00572] (3) Wipe the engine and engine compart- ment with a dry cloth. (4) Wash down the hull, deck, and jet pump with fresh water. - Page 58 2 Minimum level mark If distilled water was added, check the bat- tery voltage. It is recommended to have a Yamaha dealer check the battery voltage and charge the bat- tery. If you charge the battery yourself, be sure to read and follow the instructions pro-...
- Page 59 1 Battery terminal (3) Apply Yamaha Marine Grease Yamaha Grease A to the battery termi- nals. Recommended water-resistant grease: Yamaha Marine Grease/Yamaha Grease A (4) Store the battery in a cool, dry place. NOTICE: Storing the battery in an un- charged condition can cause perma- nent battery damage.
-
Page 60: Long-Term Storage
Storage for long periods of time, such as win- ter storage, requires preventive maintenance to ensure against deterioration. It is advisable to have the watercraft serviced by a Yamaha dealer prior to storage. However, the following procedures can be Throttle cable (throttle lever end) ... -
Page 61: Rustproofing
Care and storage Steering cable ball joint (handlebar end) Spray metallic parts of the hull and engine and steering cable inner wire (handlebar with a rust inhibitor. end) To rustproof the internal engine components: To access the steering cable ball joint (han- (1) Remove the hood. -
Page 62: Maintenance
1 Tool bag See a Yamaha dealer for genuine Yamaha re- 2 Screwdriver 3 10/12 mm box wrench placement parts and optional accessories 4 Garden hose adapter designed for your watercraft. -
Page 63: Adjusting The Jet Thrust Nozzle Angle
Maintenance (2) Remove the four screws, and then re- (8) While holding the steering pole, move move the handlebar cover. the lock pin to the stowed position, and then lower the steering pole. EJU31289 Adjusting the jet thrust nozzle angle The angle of the jet thrust nozzle can be ad- justed to two settings to suit operator prefer- ence. - Page 64 Maintenance (3) Remove the steering cable pivot bolt. TIP: The outermost hole in the steering column cannot be used. 1 Steering cable pivot bolt 2 Steering column (4) Select the nozzle angle, install the steer- 1 Nozzle angles ing cable pivot bolt with the lock washer in the desired position (P1 or P2) on the steering column, and then tighten the bolt to the specified torque.
-
Page 65: Periodic Maintenance Chart
If you have any questions, consult a Yamaha dealer. This “ ” mark indicates maintenance that you may do yourself. This “ ” mark indicates items to be checked and serviced by a Yamaha dealer. Initial Thereafter every... -
Page 66: Checking The Spark Plugs
1 Insulator 2 Electrode leak or carburetion problem in that cylinder. 3 Spark plug gap Do not attempt to diagnose any problems yourself. Have a Yamaha dealer service the Specified spark plug: watercraft. BR7HS To remove a spark plug: Spark plug gap: 0.6–0.7 mm (0.024–0.028 in) -
Page 67: Lubrication Points
Maintenance (3) Wipe off any water or dirt inside the Have a Yamaha dealer replace the fuel filter if spark plug cap. necessary. (4) Install the spark plug cap by pushing it down until it is securely installed in its original position. - Page 68 The carburetor is a vital part of the engine and requires very sophisticated adjustments. Most adjustments should be left to a Yamaha dealer who has the professional knowledge and experience to make them. However, the operator may adjust the engine idling speed as part of the usual maintenance routine.
-
Page 69: Specifications
Specifications Charging system: EJU34543 Specifications Flywheel magneto Watercraft capacity: Drive unit: Maximum people on board: Propulsion system: 1 person Jet pump Dimensions: Jet pump type: Axial flow, single stage Length: Impeller rotation: 2240 mm (88.2 in) Counterclockwise Width: Jet thrust nozzle angle: 680 mm (26.8 in) P1: 14.4+14.4°... -
Page 70: Trouble Recovery
Trouble recovery EJU34562 Troubleshooting If you have any trouble with your watercraft, use the troubleshooting chart to check for the possible cause. If you cannot find the cause, consult a Yamaha dealer. EJU34576 Troubleshooting chart TROUBLE POSSIBLE CAUSE REMEDY PAGE... - Page 71 Empty Refill as soon as pos- larly or stalls sible Stale or contaminat- Have serviced by — Yamaha dealer Too much oil in fuel Correct fuel-to-oil ra- mixing ratio tio to 50:1 Choke Knob is left pulled Push fully in...
-
Page 72: Emergency Procedures
Trouble recovery ways stop the engine before beaching the EJU34624 Emergency procedures watercraft. EJU34635 Cleaning the jet intake and impeller EWJ00783 WARNING Before attempting to remove weeds or de- bris from the jet intake or impeller area, shut the engine off and remove the clip from the engine shut-off switch. -
Page 73: Jumping The Battery
If debris is difficult to remove, consult a Yamaha dealer. EJU34642 Jumping the battery If the watercraft battery has run down, the en- gine can be started using a 12-volt booster battery and jumper cables. -
Page 74: Towing The Watercraft
Trouble recovery (4) Open the fuse holder and replace the The towline should be long enough so fuse with one of the correct amperage. that the watercraft will not collide with WARNING! Do not use fuses of a dif- the towing boat when slowing down. -
Page 75: Submerged Watercraft
[ECJ00702] (4) Turn the watercraft upright again. (5) Have the watercraft serviced by a Yamaha dealer as soon as possible. NOTICE: Be sure to have a Yamaha dealer inspect the watercraft. Other- wise, serious engine damage could result. [ECJ00792]... - Page 76 Index 2-stroke engine oil ........28 Fuel and engine oil requirements ..... 28 Fuel cock knob......... 21 After removing the watercraft from the Fuel filter, checking ........61 water............. 49 Fuel level check........35 Fuel system checks ......... 35 Battery care..........51 Fuel tank, filling ........
- Page 77 Index Periodic maintenance chart ..... 59 Post-launch checks ......... 39 Post-operation care ......... 50 Pre-launch checks ........35 Pre-operation check points ..... 35 Pre-operation checklist......33 Primary Identification (PRI-ID) number ..1 Recommended equipment ...... 12 Rustproofing ..........55 Safe boating rules ........14 Safety equipment check ......
- Page 78 Printed in Japan June 2014–0.1 × 1 CR Printed on recycled paper...