Related Manuals for Videomitter MIT500
Summary of Contents for Videomitter MIT500
- Page 1 Instruction Manual MIT500 Wireless 2MP AHD Transmission © 2023 System Q Ltd VideoMitter.com...
-
Page 2: Table Of Contents
MIT500 Table of Contents Introduction User Information Connections and Powering Signal Transmission Pairing Multiple Pairs Troubleshooting Additional Antenna Quick Links Specifications Conditions General Company Disclaimer ..................14 WEEE Declaration ......................14 Copyright ........................14 © 2023 System Q Ltd VideoMitter.com... -
Page 3: Introduction
· Do not install or use the device if the power cable or video connections are damaged. · Do not use alcohol or solvents to clean the product, only clean using a damp cloth. © 2023 System Q Ltd VideoMitter.com... -
Page 4: Connections And Powering
MIT500 Connections and Powering Before installation it is recommended to connect the whole transmission setup on a bench or local to the DVR / monitor. To ensure compatibility, and that all parts are in working order. Both the transmitter and receiver require a regulated 12V DC power supply individually. - Page 5 To power a camera via power pass-through connect the power out cable (1) on the transmitter to your camera’s power in female lead. Note - If you press and hold the reset button you will need to re-pair the units, see Pairing © 2023 System Q Ltd VideoMitter.com...
-
Page 6: Signal Transmission
MIT500 Signal Transmission Different site conditions will affect the signal transmission, and therefore will affect; distance, range and performance of the MegaMitters. In modern buildings sometimes the structure is lined with “FOIL”. This can reflect or “ground” the wireless signal, avoid transmitting through such. -
Page 7: Pairing
3. Once pairing is complete both Link LEDs will display solid Green. If a monitor is connected to the RECEIVER it will display a signal strength bar at the top left hand corner of the display. © 2023 System Q Ltd VideoMitter.com... -
Page 8: Multiple Pairs
MIT500 Multiple Pairs When installing it is good practice to keep the MegaMitters away from another transmission devices including other MegaMitters. This is because interference can cause poor performance which may result in intermittent loss of signal or non operation. -
Page 9: Troubleshooting
AHD 720p / AHD 1080p. 3. If a camera is also being powered from the same power supply (at the TX), then the camera may require a separate power supply to drive the camera and the MegaMitter. © 2023 System Q Ltd VideoMitter.com... - Page 10 MIT500 Flashing green Link LED This means the MegaMitters units are not paired or there is no input video signal to the TX unit. 1. The wireless signal between the TX and RX is low, meaning something is impeding the signal, stopping the transmission - see Signal Transmission 2.
-
Page 11: Additional Antenna
This range can be extended up to 1Km. *Line of sight means no physical obstacles and the antennas can actually see each other. To see our full range of aerials please visit; https://systemq.com/store/Category/Wireless-CCTV-Video-Antennas © 2023 System Q Ltd VideoMitter.com... -
Page 12: Quick Links
MIT500 Quick Links http://www.videomitter.com/ https://voiceoff.com/ 10/08/2023 VideoMitter.com... -
Page 13: Specifications
-30 ~ 70ºC Delay 150mS Max Modulation 16QAM/QPSK/BPSK Transmission Channels 19 (FHSS – maximum 4 pairs per site Pair separation distance Minimum of 2m apart Dimensions 110mm x 95mm x 25mm (Not including aerials or wires) © 2023 System Q Ltd VideoMitter.com... -
Page 14: Conditions
WEE/CG0783SS collection point as defined by your local council. 11.3 Copyright © Copyright 2023 VideoMitter is a registered trademark of System Q Ltd, Chesterfield. Derbyshire. S40 2WB 10/08/2023 VideoMitter.com...
Need help?
Do you have a question about the MIT500 and is the answer not in the manual?
Questions and answers