Troubleshooting; Warranty - Dometic Mobil AIR PRO 361 Installation And Operating Manual

Troubleshooting

I
NOTE
• During first exposure to water there may be some
moisture at the seams. Through this moisture the threads
will swell and fill the holes that are created in the sewing
process.
• A fully equipped spare parts kit should include:
– Waterproofer
– Repair tape and repair solution
– Silicone spray for the zippers
– Spare pegs
Problem Solution
➤ Check that the valve is fully screwed into the air
Awning tent only inflates
with difficulties
➤ Check if the inflation tube is twisted at the
➤ Check that the hand pump is working.
➤ Check that all isolation valves (fig. i, page 6
Part of the awning tent
does not inflate
➤ Check that all isolation valves (fig. i, page 6
Part of the awning tent
does not deflate
➤ Add more air (9 psi/0.62 bar).
Air poles are kinked
➤ Check that the valve is fully screwed into the air
Air leak
➤ Check that the cap of the valve is done up
➤ Check for punctures, see chapter "Repairing a
➤ Check for leaky seams, damaged tapings and
Water leak
➤ If you cannot find any leaks, see chapter "Con-
➤ If you find any leaks, apply seam sealant.
➤ Use repair tape to seal the fabric.
Rip in the fabric
➤ Have repairs carried out by an authorized
Condensation
All awning tents suffer from internal condensation if one or more of the
following conditions apply:
• High air humidity
• High ground moisture
• A drop in temperature
Severe condensation can run down the inside of the roof and drip off ties,
tapes and other internal fittings and can be mistaken for leaking.
➤ Increase ventilation by opening doors and/or windows.
➤ Install a waterproof groundsheet.
Repairing a puncture in the air pole
If the air pole loses air, proceed as follows:
1. Unzip the outer sleeve holding the air pole.
2. If installed, close isolation valves.
3. Remove the air pole.
4. Deflate the air pole.
5. Unzip the protective sleeve to expose the inflatable tube.
6. Blow some air into the inflatable tube.
7. Submerge the tube in water.
8. Locate the puncture.
9. Use repair tape and repair solution to seal the hole.
10
pole.
valve. This may be indicated by noise. Untwist
the inflation tube.
that connect the air poles are open.
that connect the air poles are open.
pole and the ring seal is in place.
tightly.
puncture in the air pole" on page 10.
moist areas.
densation" on page 10.
specialist.
10. Zip the inflatable tube back into the protective sleeve.
11. Zip the air pole back into the outer sleeve.
➤ Also observe the information given in fig. k, page 7.
Disposal
➤ Place the packaging material in the appropriate recycling
waste bins wherever possible.
➤ Consult a local recycling center or specialist dealer for
details about how to dispose of the product in accordance
with the applicable disposal regulations.

Warranty

The statutory warranty period applies. If the product is defective, please
contact your retailer or the manufacturer's branch in your country (see
dometic.com/dealer).
For repair and warranty processing, please include the following docu-
ments when you send in the product:
)
• A copy of the receipt with purchasing date
)
• A reason for the claim or description of the fault
Note that self-repair or non-professional repair can have safety conse-
quences and might void the warranty.
The warranty covers manufacturing defects, materials and parts. The
warranty does not cover fading of the cover and wear and tear due to
UV radiation, misuse, accidental damage, storm damage, or permanent,
semi-permanent or commercial use. It does not cover any resulting
damage. Please contact your dealer for claims. This does not affect your
statutory rights.
4445103307
EN