Related Manuals for Original inside EUROTOP 701 A
Summary of Contents for Original inside EUROTOP 701 A
- Page 1 99 288.GB.80I.0 EUROTOP 701 A (Type SK 288 : + . . 01436) • Double Rotary Swather Ihre / Your / Votre • Masch.Nr. • Fgst.Ident.Nr.
- Page 2 Dear Farmer You have just made an excellent choice. Naturally we are very happy and wish to congratulate you for having chosen Pöttinger. As your agricultural partner, we offer you quality and efficiency combined with reliable servicing. In order to assess the spare-parts demand for our agricultural machines and to take these demands into consideration when developing new machines, we would ask you to provide us with some details.
- Page 3 INSTRUCTIONS FOR Dokument PRODUCT DELIVERY PÖTTINGER Landtechnik GmbH Industriegelände 1 A-4710 Grieskirchen Tel. 07248 / 600 -0 Telefax 07248 / 600-2511 According to the product liability please check the above mentioned items. Please check. Machine checked according to delivery note. All attached parts removed. All safety equipment, drive shaft and operating devices at hand.
-
Page 4: Table Of Contents
TABLE OF CONTENTS Observe Safety Hints in the supplement! Table of contents Meaning of warning signs............4 Technical Data ................19 CE sign ..................4 Necessary connections ............. 19 Hitching ..................5 Position of Vehicle Identification Plate ........19 Hydraulic connection ..............5 Optional equipment .............. -
Page 5: Hitching
HITCHING Hitching Hydraulic connection Safety hints: EUROTOP 771, 801, 881 There must be at least one double action and one single action see supplement-A1 points 8a. - 8h.) hydraulic connection available on the tractor (DW, EW). Single action hydraulic connection: If the tractor only has a single - Hitching the machine to the lifting gear of the tractor. -
Page 6: Lenght Of The Drive Shaft
HITCHING Lenght of the drive shaft - Before using for the first time, the length of the drive shaft must be checked and adjusted if necessary (see also supplement B „Drive shaft adaption“). 025-05-04 Procedure for cutting to length - To determine length required, set implement in closest working position (L2) to tractor, hold driveshaft halves side by side and mark off. -
Page 7: Lowering The Machine
HITCHING Should problems occur when disconnecting: Lowering the machine - Move servo-valve (ST) briefly to "lower" position (s). The machine can be lowered both from the working Doing this will reduce any possible pressure remaining in the position and from the transport position. connector and allows a trouble-free disconnection of the hydraulic Park machine stabily! lines. -
Page 8: Conversion From Working To Transport Position
TRANSPORT POSITION Conversion from working to transport position Attention! • For safety reasons, turn off drive shaft and 4. Make sure that swivel area is free and that Changing from wait for rotor to stop completely. nobody is standing in the danger area. working position •... -
Page 9: Driving On Public Roads
TRANSPORT POSITION Driving on public roads Only transport the machine in the transport position Attention! (H2)! Observe the following steps: • Swivel the rotary units completely up (H2) • Close stop cock (position A) TD44/94/8 Locking occurs hydraulically, the locking hooks (10) •... -
Page 10: Working Position
WORKING POSITION 4. Lower both rotor units into operating position. Working position • Stopcock epened (position E). • Move single action servo-valve (ST) briefly to "lift" position Stand clear of implement's swivel range. simultaneously pulling on rope (S). This releases locking hooks(10). -
Page 11: Preparing For Operation
WORKING POSITION Preparing for operation Adjustment of the working width Depending on the crop conditions and to adapt the machine to the following implements (chopper, self-loading forage waggon), Caution! it is possible to vary the machine working width between 6,3 and Do not enter rotor area while driving motor is 7,1 m. -
Page 12: Swather With „Multitast" System
THE SYSTEM "MULTITAST" Swather with „MULTITAST“ system Turning joint (1) The rotary units are not seated on rigid bearings, but in a turning joint (1). Feeler wheel (2) Using the feeler wheel enables the tines to attain optimum ground adaption (6°) even on extremely uneven surfaces. As the tines are located quite close to the feeler wheel they are able to follow the uneven ground optimumly. - Page 13 THE SYSTEM "MULTITAST" EUROTOP 701 A / 771 A / 881 A Fixing the rotary unit: • Remove axle • Remove 6 (M14x35) hexagonal screws • Swivel the axle bearer around 180° to the rear (4a) and refit • Refit the axle (pos. 4) •...
-
Page 14: General Guidelines For Working With The Machine
OPERATION General guidelines for working with the machine Safety hints - All work in the immediate area of the rotors may only be carried out when the p.t.o. is switched off. 1. Turn p.t.o. on. Turn the p.t.o. on only when all safety devices (coverings, protective Caution! aprons, casings, etc.) are in proper condition and attached to the implement in the correct protective positions. -
Page 15: Swathes With Only One Rotary Unit
OPERATION Swathes with only one rotary unit Caution! Note! Because of the double-jointed drive travelling with Do not enter rotor only one rotary unit over swathes already made or for Do not raise the rotary unit beyond the field area while driving reasons of space can also take place. -
Page 16: Take Care When Turning On Slopes
WORKING ON SLOPES Take care when turning on slopes! Safety advice • Reduce speed The tractor's travelling characteristics are in curves accor- influenced by the weight (G) of the rotor dingly. unit. This can lead to dangerous situations, especially on slopes. •... -
Page 17: Maintenance
MAINTENANCE Safety point Parking in the ope Safety points! • Turn engine off when adjustment, service and repair When parking in the open for work is to be done. long periods of time, clean • Turn engine off piston rods and then coat when adjustment, with grease. -
Page 18: Lubrication Chart
MAINTENANCE Lubrication chart after every 20 hours operation once a year FETT GREASE (IV) see supplement "Lubrificants" Liter Litre Transmission Quantity: 1 L SAE 90 Oil level check: The oil level is correct when the oil comes up to the level screw (1). Changing oil: after 500 ha at the latest. - Page 19 MAINTENANCE Tine arms • In normal operation the gap (A) should be approx. 1 • If the gap (A) is greater than 4 mm then change the mm. If shaft play (W) is greater then it can be corrected bushings (B) on the inner side of the tine arms. Otherwise Take Note! with washers consequent damage can occur to the machine.
-
Page 20: Technical Data
Transport height - rotors swivelled up Defined use of the Rotary Swather ab 44 kW (60 PS) Required power The "EUROTOP 701 A" Rotary Swather is 1500 kg Weight with drive shaft intended solely for normal use in agricultural work. -
Page 21: Supplement
SUPPLEMENT GB-Anhang Titelblatt _BA-Allgemein... - Page 22 The original cannot be copied ... Things will run better with genuine Pöttinger parts • Quality and precise fitting The decision must be made, ”original” or ”imitation”? The decision is often governed by price and a ”cheap buy” can sometimes be very expensive. - Operating safety.
-
Page 23: Recommendations For Work Safety
Recommendations for work safety SUPPLEMENT - A Recommendations for work safety 6.) Transport of persons prohibited All points refering to safety in this manual are indicated a. The transport of persons on the machine is not permitted. by this sign. b. -
Page 24: Driveshaft
DRIVESHAFT Supplement - B Matching driveshaft to tractor Rules for working To determine the actual length required, hold the two Never exceed the maximum p. t. o. speed when using halves of the driveshaft side by side. the implement. Important! - When the p.t.o. - Page 25 DRIVESHAFT Supplement - B How a cam type cut out safety clutch works This overload clutch switches the torque transmitted to zero if overloaded. To revert to normal operation, stop the p.t.o. drive briefly. The clutch reengages at a speed below 200 rpm. IMPORTANT! Re-engaging is also possible by decreasing the p.t.o.
-
Page 28: Important! Additional Information
IMPORTANT! ADDITIONAL INFORMATION Combination of tractor and mounted implement The mounting of implements on the front or rear three point linkage shall not result in exceeding the maximum permissible weight, the permissible axle loads and the tyre load carrying capacities ot the tractor. The front axle of the tractor must always to be loaded with at least 20 % of the unladen weight of the tractor. -
Page 29: Important! Additional Information
IMPORTANT! ADDITIONAL INFORMATION 3. CALCULATION OF THE REAL FRONT AXLE LOAD T V tat (If with the front mounted implement (G ) the required minimum front ballasting (G ) cannot be reached, the weight of the front mounted V min implement has to be increased to the weight of the minimum ballasting at the front!) Record the calculated real front axle load and the permissible front axle load of the tractor into the table. - Page 30 Yrityksen nimi ja valmistajan osoite:: PÖTTINGER Landtechnik GmbH Industriegelände 1 AT - 4710 Grieskirchen Kone (vaihdettava varuste): Karhotin EUROTOP 701 A Tyyppi Sarjanumero Valmistaja vakuuttaa, että puolivalmiste täyttää – niin pitkälle kuin se on toimituskokoonpanon osalta mahdollinen – seuraavien EY-direktiivien olennaiset vaatimukset.: Koneet 2006/42/EG Lisäksi vakuutetaan määräystenmukaisuus seuraavien muiden EY-direktiivien ja/tai asiaan...
- Page 31 Im Zuge der technischen Weiterentwicklung La société PÖTTINGER Landtechnik GmbH Following the policy of the PÖTTINGER arbeitet die PÖTTINGER Landtechnik améliore constamment ses produits grâce Landtechnik GmbH to improve their products GmbH ständig an der Verbesserung ihrer au progrès technique. as technical developments continue, Produkte.
- Page 32 PÖTTINGER Landtechnik GmbH A-4710 Grieskirchen Telefon: +43 7248 600-0 Telefax: +43 7248 600-2513 e-Mail: info@poettinger.at Internet: http://www.poettinger.at PÖTTINGER Deutschland GmbH Verkaufs- und Servicecenter Recke Steinbecker Strasse 15 D-49509 Recke Telefon: +49 5453 9114-0 Telefax: +49 5453 9114-14 e-Mail: recke@poettinger.at PÖTTINGER Deutschland GmbH Servicecenter Landsberg Spöttinger-Straße 24 Postfach 1561...