Shark S3300 Owner's Manual page 6

OPERATING INSTRUCTIONS
Components
On/Off Power Switch: The On/Off
switch has a light that will illuminate
when the unit is plugged into the 120V
wall outlet and the switch turned to the
"On" position.
Heating Light: The heating light located
on the handle will turn on when the unit
is turn "On" but will turn off when the
steam is ready.
CAUTION:
Read the instructions for
"Filling the Water Tank" before opening
the Safety Cap.
CAUTION:
Always unplug before
filling. ALLOW UNIT TO COOL FOR
FIFTEEN (15) MINUTES BEFORE
REFILLING.
IMPORTANT:
Do NOT add cleaning
solutions, scented perfumes, oils or any
other chemicals to the boiler in this
appliance. Use tap water or
distilled/purified water if the tap water
in your area is very hard.
Filling or Refilling Your Steam
Cleaner With Water
IMPORTANT:
Always insure that the unit
is "UNPLUGGED" from the wall receptacle
prior to initial filling or re-filling the water
tank and has been allowed to cool for 15
minutes. Never attempt to fill this unit
under a water tap, always use the filling
funnel provided.
1. Before filling or refilling the steam
cleaner, make sure that the unit is NOT
plugged in and has been allowed to cool
for fifteen (15) minutes.
2. Press the steam trigger on the hand grip
to vent any residual steam that is in the
boiler.
3. Place the unit on a flat, stable surface.
Push down firmly on the safety cap
and slowly turn the safety cap counter
clockwise until it is removed.
4. Place the funnel in the tank opening.
(Fig. 1) Fill with a maximum of one filling
flask or 2 cups (500 ml) of water. Do Not
Overfill. Turn the safety cap clockwise
to replace.
NOTE: To remove or replace the safety
cap, push down on it firmly and rotate it
clockwise to tighten or counter clock-wise to
loosen. If not depressed the cap will rotate
freely without advancing.
NOTE: Filling the unit with hot water will
shorten the heat up time.
Fig. 1
WARNING:
Extreme care should be
taken when refilling the unit. Allow
unit to cool for 15 minutes before
refilling. When refilling the steam
cleaner while the boiler is still hot, there
is a risk that water will squirt back
during filling and cause scalding.
Extreme care should be taken when
refilling the unit. Use caution when
opening the Safety Cap as cap may
become hot during use and escaping
steam can cause scalding.
5. Connect desired attachments
onto the Flexible Steam Hose.
6. Plug the unit into a standard (120
volt, grounded) wall receptacle and
switch the On/Off switch to the "On"
position. Allow approximately 8-10
minutes for vapor to reach its
working temperature and pressure.
When the unit is ready for use, the
red light will change to green. Always
point nozzle outlet in a safe direction.
At the start, some water will come
out from the nozzle. This is normal.
NOTE: When the steam cleaner has
run out of water, steam output will
cease.
7. When finished using the unit turn off
and unplug.
WARNING: This appliance is under
pressure. After every use, press steam
trigger button until all pressure has been
released before removing safety cap.
Allow unit to cool for fifteen (15) minutes
before refilling.
5
CONSIGNES D'UTILISATION
Pose de la Bandoulière
La bandoulière permet une plus grande
liberté de mouvements lorsque les deux
mains sont nécessaires au nettoyage.
Pour attacher la bandoulière au
nettoyeur à vapeur, pressez
simplement les crochets aux anneaux
de connexion sur l'appareil. Voir les
figures 8, 9 et 10.
Anneau de
connexion
Anneau
de
connexion
Fig. 8
Fig. 9
Fig. 10
IMPORTANT:
Lorsque vous utilisez
le nettoyeur à vapeur avec la
bandoulière, évitez de bercer ou
d'incliner l'appareil de façon
excessive, afin d'éviter que de l'eau
n'entre dans le tuyau et ne soit
éjectée avec la vapeur.
34