Contents Introduction..............2 Transportation, storage and disposal......15 Safety................3 Technical data.............. 15 Assembly..............10 Accessories..............17 Operation..............11 Registered trademarks..........17 Maintenance..............13 Declaration of Conformity..........18 Troubleshooting............14 Introduction Intended use Accessories on page 17 . Make sure to accessories in read this manual together with the approved accessory This power unit is a bare unit that only function...
Note: Other symbols/decals on the product refer to Rated voltage, V certification requirements for other commercial areas. Manufacturer Husqvarna AB Direct current. Drottninggatan 2, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500 The product has protection against splashing water.
Page 4
the adjacent area if the instructions in the • If operating a power tool in a damp location is manual are not obeyed. unavoidable, use a residual current device (RCD) protected supply. Use of a RCD reduces the risk of electric shock.
Page 5
tool or these instructions to operate the power tool. will ensure that the safety of the power tool is Power tools are dangerous in the hands of untrained maintained. users. • Never service damaged battery packs. Service of • Maintain power tools and accessories. Check for battery packs should only be performed by the misalignment or binding of moving parts, breakage manufacturer or authorized service providers.
Page 6
slipping and falling which may result in personal • Before using the product and after any impact, injury. check for signs of wear or damage and repair as necessary. • When working on slopes, always be sure of your footing, always work across the face of slopes, never •...
Page 7
• Keep hands and feet away from the cutting area inspect or repair the product and/or the cutting at all times and especially when switching on the equipment. motor. • Ensure that people, animals or other things can • Keep your hands and feet away from the cutting not affect your control of the product or that they attachment until it has stopped completely when the do not come in contact with the cutting attachment...
Page 8
occur. Let your dealer help you select the right carried out professionally. If you need further information equipment. please contact your nearest servicing dealer. • Use a protective helmet where there is a risk of WARNING: falling objects. Never use a product with defective safety components.
Page 9
5. Push the power trigger fully to apply full speed. 6. Release the power trigger and make sure that the cutting attachment stops and remains still. Safety instructions for assembly WARNING: Read this power unit manual together with approved accessory manual.
Assembly To assemble the loop handle 2. Align the tab (A) with the arrow (B) on the coupling. 1. Attach the loop handle onto the shaft between the arrows. Do not place loop handle or suspension ring on label. 3. Push the shaft into the coupling until it clicks into position.
Read and understand the safety chapter before you use the product. To connect the battery to the product WARNING: Only use Husqvarna original batteries with the product. 1. Make sure that the battery is fully charged. CAUTION: If the battery does not move easily into the battery holder, the battery is not installed correctly.
Page 12
Work position 1. Push the mode button to set a limit to the maximum speed. The white LEDs comes on to show that the • Hold the product with 2 hands. function is on. • Hold the product on the right side of your body. •...
Husqvarna Fleet Services is a cloud solution that your mobile device. gives the commercial fleet manager an overview of all ™ 2. Log on to the Husqvarna Fleet Services app. ™ products. Husqvarna Fleet Services can be added to 525iLK. For more information about Husqvarna Fleet 3.
Maintenance Daily Weekly Monthly Clean the external parts of the product with a dry cloth. Do not use water. Examine that the start and stop button works correctly and is not damaged. Make sure that the power trigger and the power trigger lockout function correctly from a safety point of view.
LED display Possible faults Possible action Red error LED flashes Overload. The cutting attachment is jammed. deacti- vate the product. Remove the battery. Clean the cutting attachment from unwanted mate- rials. Temperature deviation. Let the product cool down. The power trigger and the acti- Release the power trigger and the product is vate button are pressed at the active.
Page 16
525iLK together with approved accessories Motor type Husqvarna E-torq BLDC Speed of output shaft, 1/min 5800 Weight Weight (power unit only), kglb 2.9/6.4 Weight (power unit incl. battery BLi200) kg/lb 4.2/9.3 Noise emissions Sound power level, measured dB (A) 89-103...
Bluetooth SIG, inc. and any use trademarks owned by of such marks by Husqvarna is under license. This is a specific number of an approved attachment within in an attachment group. The approved attachments are divided into attachment groups. Each attachment group has similar features and decals.
Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated Power Unit Brand Husqvarna Type / Model 525iLK Identification Serial numbers dating from 2023 and onwards...
Page 19
UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated Power Unit Brand Husqvarna Type / Model 525iLK Identification Serial numbers dating from 2023 and onwards complies fully with the following UK regulations:...
Page 20
Original instructions 1143041-26 2023-03-03...