Titan TRS22TX - Wireless PIR Detector Quick Start Guide
OVERVIEW
Front Cover | Battery |
PIR Motion Sensor | Rear Cover |
Time-off Knob | Tamper Switch |
The PIR Detector is designed to detect movement in a protected area by detecting moving heat sources, for example, when a person moves within or across the devices field of vision. When movement is detected a radio signal will be emitted to the Receiver(s).
The recommended position for mounting the PIR Detector is approximately 1.8 to 2m from the floor. At this height, the detector will detect movement up to 8-12m depending on adjustment.
Before selecting a position for a PIR Detector the following points should be noted:
- Do not position the detector facing direct sunlight.
- Do not position the detector directly above or facing any source of heat, eg: fires, radiators, boiler etc.
- Where possible, mount the detector so that the logical path of an intruder would cut across the fan pattern rather than directly towards the detector.
- The PIR Detector can be used with all TRS receivers providing they are all coded with the same code.
LOADING THE BATTERY
- Using a Phillips screwdrivers to detach the rear cover.
- Insert 2 AAA-size 1.5V batteries to the battery compartment, ensuring correct polarity.
- Refit the rear cover, when any settings are completed and the unit has been fixed in place.
SETTING
- The units ID code is fixed ex-factory and cannot be adjusted.
- Emitting the ID code
- After inserting the batteries to the PIR Detector, it will have a 60-second warm up period before emitting the ID code.
- Set the Receiver to code learning mode. (refer to Receiver's instruction manual).
- Pressing the tamper switch for more than 3 seconds will emit the ID code to the Receiver.
- If the Receiver responds with a long bleep, the code learning is successful. If not, please repeat Step 2.
- If consecutive short bleeps have been heard from the Receiver, the code learning has failed.
- Start again from Step 1 to re-try.
OPERATION
TAMPER
- When removing the rear cover, the tamper switch will be triggered. The trigger command signal will be sent to the Receiver immediately.
- If coded TITAN Chime / Alarm Receivers will sound in alarm mode for approximately 30 seconds be silent for approximately 10 seconds, then sound again for approximately 30 seconds. This will repeat until cancelled on the receiver or for 10 cycles of 30 seconds.
NORMAL ACTIVATION
- When the PIR Detector is triggered by moving heat source a radio signal is transmitted to the Receiver to activate the receivers coded to it.
- The time control knob is designed to control the length of time that the receiver should is turned on. It is set from 5 seconds to 12 minutes. "T" means 5 seconds, while "+" is 12 minutes.
- An LED is mounted inside of the PIR Detector. The indication of LED represents the following status:
| Status | LED indication |
1 | PIR Detector is emitting radio signal | Illuminating steadily |
2 | Low battery | Flashing every 30 seconds |
INSTALLATION
As soon as the code learning procedure is completed, hold the rear cover in position and mark the two mounting holes. Drill the holes, insert the plastic wall plugs and screw the rear cover to the wall using the screws supplied. Offer the Detector up to the rear cover using screws as originally supplied.
NB: After removing the batteries, wait for 1 minute before refitting new batteries.
NB: After replacing the batteries wait 10 seconds for the detector to become stable.
TROUBLESHOOTING
Symptom | Possible Cause | Recommendation |
Device not working | Flat battery | Replace with new battery |
Check if mounting location of detector is correct | Adjust mounting location |
Radio interference | Remove interference source or change mounting location |
SPECIFICATIONS
Frequency Range | 433MHz |
Battery | 1.5V AAA x 2 |
Communication Range | 70 m (in an open space) |
Specifications subject to change without notice
Documents / ResourcesDownload manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Titan TRS22TX - Wireless PIR Detector Quick Start Guide
Need Assistance?
Do you have a question about the TRS22TX that isn't answered in the manual? Leave your question here.