PCE Health and Fitness MD360P PUCK Installation

433 mhz wireless magnetic field vehicle detector

Advertisement

Quick Links

433 MHz
Wireless Magnetic Field Vehicle Detector
Model – MD360P PUCK & MD360C CONTROLLER
The MD360P (Puck)
The Puck has been designed to be buried in the road surface underneath the vehicle path. It is suitable for
Installation in any stable surface (bitumen, concrete, compacted earth etc.) and can be easily installed into a
70mm core drilled hole.
The MD360C (Controller) is a wireless control unit which enables
configuration and output of the
configuration and LED's are used for visual indication of the operation of the
Puck. A relay output switches ON when a vehicle is detected.
The MD360 series has been designed for parking and access control
applications and is a cost-effective wireless solution for detecting vehicles in
order to facilitate the automatic opening of security gates. It requires a
minimal amount of cutting in the road surface to install.

Features

Wireless connectivity. ● Up to 50 meters range
Battery Life (MD360P only). Up to 5 years battery life @ 25℃
Reset Switch. ● Reset the Puck from Controller
● Easily pair Puck to Controller
Switch selectable Sensitivity. Two sensitivity settings are available on the switches to allow for flexibility in
configuration.
Filter Option. Prevent false detection of small or fast-moving objects.
Relay Mode. Configure the relay to operate in presence or pulse mode.
Pulse Relay Selection. Configure relay to pulse on vehicle detect or undetect.
Motion Filter. Only trigger output once the vehicle has stopped moving for at least 1 second.
Presence settings. While in detect, puck will reset after selected timeout: 5min, 30min, 2hr and no-timeout.
. DIP switches are used for
MD360P
● ETSI EN300-220 Compliant for use in Africa/Australia/Europe/NZ/UK
(Puck adjusts to the environment becoming ready for vehicle detection).
(Note: Only one puck can be paired to a controller at one time).
Combines a magneto resistive sensor with a low power
battery operated radio transceiver. This combination results in
a self-contained wireless vehicle detector that does not
require a loop or any cables to be run to it making installation
times quicker.
The Puck's sensor detects changes in the earth's magnetic
field due to the presence of a vehicle, which results in a
detect signal being output to the MD360 Controller.
(Line of Sight).
(Calculated @ 1 detect per minute).
1
V02

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MD360P PUCK and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for PCE Health and Fitness MD360P PUCK

  • Page 1 433 MHz Wireless Magnetic Field Vehicle Detector Model – MD360P PUCK & MD360C CONTROLLER The MD360P (Puck) Combines a magneto resistive sensor with a low power battery operated radio transceiver. This combination results in a self-contained wireless vehicle detector that does not require a loop or any cables to be run to it making installation times quicker.
  • Page 2 Technical Specifications – MD360C (Controller) Power supply 12 - 24VAC/DC 50/60Hz 45mA Radio Specifications Frequency: 433.92 MHz Power: 10 dBm Modulation: 2FSK Bandwidth: 250 kHz Antenna: 1.8 dB Dipole Antenna (Supplied with controller) Presence/Pulse Relay Change over contact 0.5A/220VAC Response time Approximately 1s after vehicle enters Puck area.
  • Page 3 Wiring Connections – MD360C Controller Screw Description Terminal Power Supply 0V Power Supply +V Relay Normally Closed N/C Relay Common COM Relay Normally Open N/O Technical Specifications – MD360P (Puck) Power 1x 3.6V 9000 mAh Li-SOCL2 Radio Specifications Frequency: 433.92 MHz Power: 10 dBm Modulation: 2FSK Bandwidth: 250 kHz...
  • Page 4 Installation The MD360 PUCK has a 1.5m sensing range, best detection results are obtained when the PUCK is mounted underneath and as close to the vehicles path as possible. The PUCK can be mounted as follows: Buried in the ground alongside the passage of the vehicle. Buried in the road beneath the vehicle.
  • Page 5 Diagnostics SYMPTOM POSSIBLE CAUSE SOLUTION The POWER LED is not No power supply voltage on Check that the power supply is correctly wired the input. to the controller. (Terminals 1 and 2) The POWER LED is The PUCKS battery voltage is Order replacement MD360P.

This manual is also suitable for:

Md360c

Table of Contents